5962D9569401VEC

HS-0548RH, HS-0549RH TM Data Sheet August 2001 File Number 3543.4 Radiation Hardened Single 8/Differential 4 Channel CMOS Analog Multiplexers with Active Overvoltage Protection tle 8R S9R iadle ifn4 nOS tiThe HS-0548RH and HS-0549RH are radiation hardened analog multiplexers with Active Overvoltage Protection and guaranteed rON matching. Analog input levels may greatly exceed either power supply without damaging the device or disturbing the signal path of other channels. Active protection circuitry assures that signal fidelity is maintained even under fault conditions that would destroy other multiplexers. Analog inputs can withstand constant 70V peak-to-peak levels with ±15V supplies and digital inputs will sustain continuous faults up to 4V greater than either supply. In addition, signal sources are protected from short circuiting should multiplexer supply loss occur: each input presents 1kΩ of resistance under this condition. These features make the HS-0548RH and HS-0549RH ideal for use in systems where the analog inputs originate from external equipment or separately powered circuitry. Both devices are fabricated with 44V dielectrically isolated CMOS technology. The HS-0548 is an 8 channel device and the HS-0549 is a 4 channel differential version. If input overvoltage protection is not needed, the HS-0508 and HS-509 multiplexers are recommended. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. Detailed Electrical Specifications for these devices are contained in SMD 5962-95694. A “hot-link” is provided on our homepage for downloading. http://www.intersil.com Features • Electrically Screened to SMD # 5962-95694 • QML Qualified per MIL-PRF-38535 Requirements • Gamma Dose . . . . . . . . . . . . . . . . . . . . . . 1 x 104RAD(Si) • No Latch-Up • No Channel Interaction During Overvoltage • Guaranteed rON Matching • Maximum Power Supply . . . . . . . . . . . . . . . . . . . . . . 44V • Break-Before-Make Switching • Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . ±15V • Access Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0µs Applications • Data Acquisition Systems • Control Systems • Telemetry Pinouts HS-0548RH GDIP1-T16 (CERDIP) OR CDIP2-T16 (SBDIP) TOP VIEW AO 1 ENABLE 2 -VSUPPLY 3 IN 1 4 IN 2 5 IN 3 6 IN 4 7 16 A1 15 A2 14 GND 13 +VSUPPLY 12 IN 5 11 IN 6 10 IN 7 9 IN 8 ve rec) tho Ordering Information ORDERING NUMBER 5962D9569401VEA 5962D9569401VEC 5962D9569402VEA 5962D9569402VEC INTERNAL MKT. NUMBER HS1-0548RH-Q HS1B-0548RH-Q HS1-0549RH-Q HS1B-0549RH-Q TEMP. RANGE (oC) -55 to 125 -55 to 125 -55 to 125 -55 to 125 OUT 8 HS-0549RH GDIP1-T16 (CERDIP) OR CDIP2-T16 (SBDIP) TOP VIEW A0 1 ENABLE 2 -VSUPPLY 3 IN 1A IN 2A IN 3A IN 4A OUTA 4 5 6 7 8 16 A1 15 GND 14 +VSUPPLY 13 IN 1B 12 IN 2B 11 IN 3B 10 IN 4B 9 OUT B 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2001, All Rights Reserved HS-0548RH, HS-0549RH Functional Diagrams HS-0548 HS-0549 IN1 1K IN2 1K DECODER/ DRIVER OUT IN1A 1K IN4A 1K IN1B 1K IN4B DECODER/ DRIVER OUT A OUT B 1K IN8 OVERVOLTAGE CLAMP AND SIGNAL ISOLATION 5V REF LEVEL SHIFT OVERVOLTAGE CLAMP AND SIGNAL ISOLATION 5V REF LEVEL SHIFT † DIGITAL INPUT PROTECTION †††† † DIGITAL INPUT PROTECTION †† † A0 A1 A2 EN A0 A1 EN HS-0548 TRUTH TABLE A2 X L L L L H H H H A1 X L L H H L L H H A0 X L H L H L H L H EN L H H H H H H H H “ON” CHANNEL NONE 1 2 3 4 5 6 7 8 A1 X L L H H A0 X L H L H HS-0549 TRUTH TABLE “ON” CHANNEL PAIR NONE 1 2 3 4 EN L H H H H Switching Waveforms ±10V IN 1 IN 2 THRU IN 7 IN 8 GND -10V VAH OUT VOUT 10K CH 8 ON 200ns/DIV. ± 10V VA I NPUT 2V/DIV. CH 1 ON OUTPUT A 5V/DIV. VAH = 4.0 ADDRESS DRIVE (VA) 1/2VAH +10V -8V tA VAL = 0V OUTPUT A A2 VA A1 A0 EN FIGURE 1. ACCESS TIME 2 HS-0548RH, HS-0549RH Switching Waveforms VAH = 4.0 ADDRESS DRIVE (VA) VA A2 A1 A0 50% 50% OUTPUT EN GND VAH 1K OUTPUT 1V/DIV. +5V IN 1 IN 2 THRU IN 7 IN 8 OUT VA INPUT 2V/DIV. CH 1 ON CH8 ON (Continued) 0V VOUT tOPEN 100ns/DIV. FIGURE 2. BREAK-BEFORE-MAKE DELAY (tOPEN) VAH = 4.0 50% 0V OUTPUT 90% 90% tON(EN) tOFF (EN) A2 A1 IN 1 IN 2 THRU IN 8 +10V ENABLE DRIVE 2V/DIV. A0 EN VA GND OUT 1K CH 1 OFF CH 1 ON OUTPUT 4V/DIV. 100ns/DIV. FIGURE 3. ENABLE DELAY tON(EN) , t OFF(EN) Schematic Diagrams V+ R9 Q1 Q4 D3 LEVEL SHIFTER V+ P P P P P P P P P LEVEL SHIFTED ADDRESS TO DECODE LEVEL SHIFTED ADDRESS TO DECODE R10 TTL REFERENCE CIRCUIT P OVERVOLTAGE PROTECTION V+ ADD IN. D2 R1 200Ω D1 VN N R2 R5 R3 N R4 N N N N R6 R8 N N N R7 V- FIGURE 4. ADDRESS INPUT BUFFER AND LEVEL SHIFTER 3 HS-0548RH, HS-0549RH Schematic Diagrams (Continued) FROM DECODE +V P P P P P P OVERVOLTAGE V+ P PROTECTION N N A0 OR A0 A1 OR A1 A2 OR A2 N N N R11 IN 1K D6 D7 Q5 D4 D5 N N Q6 OUT N N V VP FROM DECODE ENABLE TO N-CHANNEL DEVICE OF THE SWITCH PAIR TO P-CHANNEL DEVICE OF THE SWITCH PAIR FIGURE 5. ADDRESS DECODER FIGURE 6. MULTIPLEX SWITCH Burn-In/Life Test Circuits V1 F0 F3 V1 D1 C1 1 2 3 4 5 6 R1 7 8 16 15 14 13 12 11 10 9 D2 C2 V2 F1 F2 V2 D1 C1 1 2 3 4 5 6 R1 7 8 16 15 14 13 12 11 10 9 D2 C2 V3 HS-0548RH DYNAMIC BURN-IN AND LIFE TEST CIRCUIT V1 V2 R1 C1 D1 F0 F1 F2 F3 = = = = = = = = = -15V maximum, -16V minimum +15V minimum, +16V maximum 10kΩ ±5% 1/4W C 2 = 0.01µF minimum (per socket) or 0.1µ F minimum (per row) D 2 = 1N4002 (or equivalent) 100kHz 50% duty cycle; VIL = 0.8V Max; VIH = 4.0V Min. F0/2 F1/2 F2/2 V1 V2 V3 R1 C1 = = = = = HS-0548RH STATIC BURN-IN TEST CIRCUIT 5V minimum, 6V maximum -15V maximum, -16V minimum +15V minimum, +16V maximum 10kΩ ±5% 1/4W C2 = 0.01µF minimum (per socket) or 0.1µF minimum (per row) D1 = D2 = 1N4002 (or equivalent) 4 HS-0548RH, HS-0549RH Burn-In/Life Test Circuits (Continued) F0 F2 V3 D1 C1 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 F1 1 2 V2 V3 D1 C1 3 4 16 15 14 13 12 11 10 9 V1 V2 D1 C1 D1 C1 5 6 7 8 R1 R1 R1 R1 HS-0549RH DYNAMIC BURN-IN AND LIFE TEST CIRCUIT V2 V3 R1 C1 D1 F0 = = = = = = +15.5V, ±.0.5V -15.5V, ±0.5V 10kΩ, ±5% 0.01µF minimum (per socket) 1N4002 or equivalent (per board) 100kHz, ±10%; F1 = F0/2; F2 = F1/2 , 50% duty cycle, VIL = 0.8V Max; VIH = 4.0V Min V1 V2 V3 R1 C1 D1 = = = = = = HS-0549RH STATIC BURN-IN TEST CIRCUIT +5.5V, ±0.5V +15.5V, ±0.5V -15.5V, ±0.5V 10kΩ, ±10% 0.01µ F minimum (per socket) 1N4002 or equivalent (per board) Irradiation Circuits +5V 1 2 16 15 14 13 12 11 10 9 R2 +15V +1V +5V 1 2 16 15 14 13 12 11 10 9 +15V +1V -15V +1V 3 4 5 6 7 8 R1 -15V +1V 3 4 5 6 7 8 R1 HS-0549RH R1 = R2 = 10kΩ ±5% HS-0548RH R1 = 10kΩ ±5% 5 HS-0548RH, HS-0549RH Die Characteristics DIE DIMENSIONS: 83 mils x 108 mils x 19 mils INTERFACE MATERIALS: Glassivation: Type: Nitride Thickness: 7kÅ ±0.7kÅ Top Metallization: Type: Al Thickness: 16kÅ ±2kÅ Substrate: CMOS, DI ASSEMBLY RELATED INFORMATION: Substrate Potential: Floating ADDITIONAL INFORMATION: Worst Case Current Density: 1.4 x 105 A/cm 2 Transistor Count: 253 Metallization Mask Layout HS-0548RH HS-0549RH IN 6 IN 7 IN 8 OUT IN 4 IN 3 IN3B IN4B OUT B OUT A IN4A IN3A IN 5 +V GND IN 2 IN 1 -V IN2B IN1B +V IN2A IN1A V- A2 A1 A0 EN GND A1 A0 EN NOTE: Pad Numbers Correspond to DIP Pin Numbers Only All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 6