HA-2546

CT RODU T LETE P TE PRODUC OBSO TITU BS LE S U - 2556 HA POSSIBData Sheet ® HA-2546 November 19, 2004 FN2861.6 30MHz, Voltage Output, Two Quadrant Analog Multiplier The HA-2546 is a monolithic, high speed, two quadrant, analog multiplier constructed in the Intersil Dielectrically Isolated High Frequency Process. The HA-2546 has a voltage output with a 30MHz signal bandwidth, 300V/µs slew rate and a 17MHz control bandwidth. High bandwidth and slew rate make this part an ideal component for use in video systems. The suitability for precision video applications is demonstrated further by the 0.1dB gain flatness to 5MHz, 1.6% multiplication error, -52dB feedthrough and differential inputs with 1.2µA bias currents. The HA-2546 also has low differential gain (0.1%) and phase (0.1 degree) errors. The HA-2546 is well suited for AGC circuits as well as mixer applications for sonar, radar, and medical imaging equipment. The voltage output simplifies many designs by eliminating the current to voltage conversion stage required for current output multipliers. For MIL-STD-883 compliant product, consult the HA-2546/883 datasheet. Features • High Speed Voltage Output . . . . . . . . . . . . . . . . . 300V/µs • Low Multiplication error . . . . . . . . . . . . . . . . . . . . . . . 1.6% • Input Bias Currents . . . . . . . . . . . . . . . . . . . . . . . . . 1.2µA • Signal Input Feedthrough . . . . . . . . . . . . . . . . . . . . . -52dB • Wide Signal Bandwidth . . . . . . . . . . . . . . . . . . . . . 30MHz • Wide Control Bandwidth. . . . . . . . . . . . . . . . . . . . . 17MHz • Gain Flatness to 5MHz. . . . . . . . . . . . . . . . . . . . . . 0.10dB Applications • Military Avionics • Missile Guidance Systems • Medical Imaging Displays • Video Mixers • Sonar AGC Processors • Radar Signal Conditioning Pinout HA-2546 (SOIC) TOP VIEW • Voltage Controlled Amplifier • Vector Generator 16 GA A GND VREF VYIOB VYIOA VY + VY VVOUT 1 REF 2 3 4 X 5 6 7 Σ 8 Y Part Number Information PART NUMBER TEMP. RANGE (oC) 0 to 65 PACKAGE 16 Ld SOIC PKG. DWG. # M16.3 15 GA C 14 GA B 13 VX + 12 VX 11 V+ 10 VZ Z 9 VZ + HA9P2546-5 + 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003, 2004. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. HA-2546 Simplified Schematic V+ VBIAS VBIAS VX + + + - VX - VZ + VZ - GA A GA C OUT GA B VY + REF 1.67kΩ VY - GND VVYIO A VYIO B 2 FN2861.6 November 19, 2004 HA-2546 Absolute Maximum Ratings Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60mA Thermal Information Thermal Resistance (Typical, Note 1) θJA (oC/W) θJC (oC/W) SOIC Package . . . . . . . . . . . . . . . . . . . 96 N/A Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (Lead Tips Only) Operating Conditions Temperature Range HA9P2546-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 65oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications PARAMETER MULTIPLIER PERFORMANCE Multiplication Error (Note 2) VSUPPLY = ±15V, RL = 1kW, CL = 50pF, Unless Otherwise Specified TEST CONDITIONS TEMP (oC) MIN TYP MAX UNITS 25 Full - 1.6 3.0 0.003 0.1 0.1 0.1 0.18 0.7 6 260 0.03 400 150 75 ±9 3 7 0.2 0.3 0.2 0.3 5.0 - % % %/oC % Degrees dB dB % MHz kHz % nV/√Hz nV/√Hz nV/√Hz V Multiplication Error Drift Differential Gain (Notes 3, 9) Differential Phase (Notes 3, 9) Gain Flatness (Note 9) DC to 5MHz, VX = 2V 5 MHz to 8MHz, VX = 2V Scale Factor Error 1% Amplitude Bandwidth Error 1% Vector Bandwidth Error THD + N (Note 4) Voltage Noise fO = 10Hz, VX = VY = 0V fO = 100Hz, VX = VY = 0V fO = 1kHz, VX = VY = 0V Common Mode Range SIGNAL INPUT, VY Input Offset Voltage Full 25 25 25 25 Full 25 25 25 25 25 25 25 25 Full - 3 8 45 7 10 10 20 15 15 mV mV µV/oC µA µA Average Offset Voltage Drift Input Bias Current Full 25 Full 3 FN2861.6 November 19, 2004 HA-2546 Electrical Specifications PARAMETER Input Offset Current VSUPPLY = ±15V, RL = 1kW, CL = 50pF, Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (oC) 25 Full Input Capacitance Differential Input Resistance Small Signal Bandwidth (-3dB) Full Power Bandwidth (Note 5) Feedthrough CMRR VY TRANSIENT RESPONSE (Note 10) Slew Rate Rise Time Overshoot Propagation Delay Settling Time (To 0.1%) CONTROL INPUT, VX Input Offset Voltage 25 Full Average Offset Voltage Drift Input Bias Current Full 25 Full Input Offset Current 25 Full Input Capacitance Differential Input Resistance Small Signal Bandwidth (-3dB) Feedthrough Common Mode Rejection Ratio VY = 5V, VX - = -1V Note 12 Note 13 25 25 25 25 25 0.3 3 10 1.2 1.8 0.3 0.4 2.5 360 17 -40 80 2 20 2 5 2 3 mV mV µV/oC µA µA µA µA pF kΩ MHz dB dB VOUT = ±5V, VX = 2V VOUT = ±5V, VX = 2V Note 7 Note 7 25 25 25 25 25 300 11 17 25 200 V/µs ns % ns ns VX = 2V V X = 2V Note 11 Note 6 25 25 25 25 25 Full MIN 60 TYP 0.7 1.0 2.5 720 30 9.5 -52 78 MAX 2 3 UNITS µA µA pF kΩ MHz MHz dB dB 4 FN2861.6 November 19, 2004 HA-2546 Electrical Specifications PARAMETER VX TRANSIENT RESPONSE (Note 10) Slew Rate Rise Time Overshoot Propagation Delay Settling Time (To 0.1%) VZ CHARACTERISTICS Input Offset Voltage V X = V Y = 0V 25 Full Open Loop Gain Differential Input Resistance OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Output Resistance POWER SUPPLY PSRR Supply Current NOTES: 2. Error is percent of full scale, 1% = 50mV. 3. fO = 3.58MHz/4.43MHz, VY = 300mVP-P, 0 to 1VDC offset, VX = 2V. 4. fO = 10kHz, VY = 1VRMS, VX = 2V. Slew Rate 5. Full Power Bandwidth calculated by equation: FPBW = -------------------------- , V PEAK = 5V . 6. VY = 0 to ±5V, VX = 2V. 7. VOUT = 0 to ±100mV, VX = 2V. 8. VS = ±12V to ±15V, VY = 5V, VX = 2V. 9. Guaranteed by characterization and not 100% tested. 10. See Test Circuit. 11. fO = 5MHz, VX = 0, VY = 200mVRMS. 12. fO = 100kHz, VY = 0, VX+ = 200mVRMS, VX- = -0.5V. 13. VX = 0 to 2V, VY = 5V. 14. VX = 0 to 200mV, VY = 5V. 2 π V PEAK VSUPPLY = ±15V, RL = 1kW, CL = 50pF, Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (oC) MIN TYP MAX UNITS Note 13 Note 14 Note 14 25 25 25 25 - 95 20 17 50 200 - V/µs ns % ns ns Note 13 25 - 4 8 70 900 15 20 - mV mV dB kΩ 25 25 VX = 2.5V, VY = ±5V Full Full 25 ±20 - ±6.25 ±45 1 - V mA Ω Note 8 Full Full 58 - 63 23 29 dB mA 5 FN2861.6 November 19, 2004 HA-2546 Test Circuits and Waveforms 1 REF NC NC NC VY + 2 3 4 X 5 + 6 V7 8 + 15 14 13 VX + 12 11 V+ + 10 Z 16 NC - - Y Σ- + 9 VOUT 1kΩ 50pF 50Ω FIGURE 1. LARGE AND SMALL SIGNAL RESPONSE TEST CIRCUIT +5V IN 0 100mV IN 0 -5V -100mV +5V OUT 0 -5V 100mV OUT 0 -100mV VERTICAL SCALE: 5V/DIV HORIZONTAL SCALE: 50ns/DIV VY LARGE SIGNAL RESPONSE VERTICAL SCALE: 100mV/DIV HORIZONTAL SCALE: 50ns/DIV VY SMALL SIGNAL RESPONSE 2V IN 0 IN 200mV 0 5V OUT 500mV OUT 0 0 VERTICAL SCALE: 2V/DIV HORIZONTAL SCALE: 50ns/DIV VX LARGE SIGNAL RESPONSE VERTICAL SCALE: 200mV/DIV HORIZONTAL SCALE:50ns//DIV VX SMALL SIGNAL RESPONSE 6 FN2861.6 November 19, 2004 HA-2546 Application Information 1 Theory Of Operation The HA-2546 is a two quadrant multiplier with the following three differential inputs; the signal channel, VY+ and VY-, the control channel, VX+ and VX-, and the summed channel, VZ+ and VZ-, to complete the feedback of the output amplifier. The differential voltages of channel X and Y are converted to differential currents. These currents are then multiplied in a circuit similar to a Gilbert Cell multiplier, producing a differential current product. The differential voltage of the Z channel is converted into a differential current which then sums with the products currents. The differential “product/sum” currents are converted to a singleended current and then converted to a voltage output by a transimpedance amplifier. The open loop transfer equation for the HA-2546 is: (VX+ - VX-) (VY+ - VY-) VOUT = A where; SF - (VZ+ - VZ-) NC NC NC VY + 2 3 4 16 NC REF 15 14 13 VX + 12 11 V+ + 10 9 VOUT 50Ω 1kΩ 50pF X 5 + 6 V7 8 + - - Y Σ- Z+ - FIGURE 2. A = Output Amplifier Open Loop Gain SF = Scale Factor VX, VY, VZ = Differential Inputs The scale factor is used to maintain the output of the multiplier within the normal operating range of ±5V. The scale factor can be defined by the user by way of an optional external resistor, REXT, and the Gain Adjust pins, Gain Adjust A (GA A), Gain Adjust B (GA B), and Gain Adjust C (GA C). The scale factor is determined as follows: SF = 2, when GA B is shorted to GA C SF ≅ 1.2 REXT, when REXT is connected between GA A and GA C (REXT is in kΩ) SF ≅ 1.2 (REXT + 1.667kΩ), when REXT is connected to GA B and GA C (REXT is in kΩ) The scale factor can be adjusted from 2 to 5. It should be noted that any adjustments to the scale factor will affect the AC performance of the control channel, VX. The normal input operating range of VX is equal to the scale factor voltage. The typical multiplier configuration is shown in Figure 2. The ideal transfer function for this configuration is: VOUT = (VX+ - VX-) (VY+ - VY-) 2 0 + VZ-, when VX ≥ 0V , when VX < 0V The VY- terminal is usually grounded allowing the VY+ to swing ±5V. The VZ+ terminal is usually connected directly to VOUT to complete the feedback loop of the output amplifier while VZ- is grounded. The scale factor is normally set to 2 by connecting GA B to GA C. Therefore the transfer equation simplifies to VOUT = (VX VY) / 2. Offset Adjustment The signal channel offset voltage may be nulled by using a 20kΩ potentiometer between VYIO Adjust pins A and B and connecting the wiper to V-. Reducing the signal channel offset will reduce VX AC feedthrough. Output offset voltage can also be nulled by connecting VZ- to the wiper of a 20kΩ potentiometer which is tied between V+ and V-. Capacitive Drive Capability When driving capacitive loads >20pF, a 50Ω resistor is recommended between VOUT and VZ+, using VZ+ as the output (see Figure 2). This will prevent the multiplier from going unstable. Power Supply Decoupling Power supply decoupling is essential for high frequency circuits. A 0.01µF high quality ceramic capacitor at each supply pin in parallel with a 1µF tantalum capacitor will provide excellent decoupling. Chip capacitors produce the best results due to the close spacing with which they may be placed to the supply pins minimizing lead inductance. Adjusting Scale Factor Adjusting the scale factor will tailor the control signal, VX, input voltage range to match your needs. Referring to the simplified schematic on the front page and looking for the VX input stage, you will notice the unusual design. The internal reference sets up a 1.2mA current sink for the VX differential pair. The control signal applied to this input will be forced across the scale factor setting resistor and set the current flowing in the VX+ side of the differential pair. When the FN2861.6 November 19, 2004 The VX- pin is usually connected to ground so that when VX+ is negative there is no signal at the output, i.e. two quadrant operation. If the VX input is a negative going signal the VX+ pin maybe grounded and the VX- pin used as the control input. 7 HA-2546 current through this resistor reaches 1.2mA, all the current available is flowing in the one side and full scale has been reached. Normally the 1.67kΩ internal resistor sets the scale factor to 2V when the Gain Adjust pins B and C are connected together, but you may set this resistor to any convenient value using pins 16 (GA A) and 15 (GA C) (See Figure 3). provides stability and a response time adjustment for the gain control circuit. This multiplier has the advantage over other AGC circuits, in that the signal bandwidth is not affected by the control signal gain adjustment. 1 1 REF NC 2 NC 3 NC 4 X VY + 5 6 V- 7 8 + 15 NC 3 14 NC 4 + 13 VX + 12 6 11 V+ V- 7 + + 10 8 9 VOUT 1N914 MULTIPLIER, VOUT = VXVY / 2V SCALE FACTOR = 2V 5kΩ 1 REF NC 2 NC 3 NC 4 X VY + 5 6 V- 7 8 + 15 14 NC 16 4.167K 20kΩ 0.1µF 1K 10kΩ +15V 10kΩ 0.1µF 0.01µF 50Ω X VY + 5 + 13 + 14 16 NC REF NC 2 15 16 NC - 12 11 V+ 10 9 VOUT - - Y - Y Σ- Z + Σ- Z + + HA-5127 3.3V FIGURE 4. AUTOMATIC GAIN CONTROL + 13 VX + - Voltage Controlled Amplifier 12 11 V+ - Y + Σ- Z + 10 9 VOUT A wide range of gain adjustment is available with the Voltage Controlled Amplifier configuration shown in Figure 5. Here the gain of the HFA0002 is swept from 20V/V at a control voltage of 0.902V to a gain of almost 1000V/V with a control voltage of 0.03V. Video Fader The Video Fader circuit provides a unique function. Here Ch B is applied to the minus Z input in addition to the minus Y input. In this way, the function in Figure 6 is generated. VMIX will control the percentage of Ch A and Ch B that are mixed together to produce a resulting video image or other signal. Many other applications are possible including division, squaring, square-root, percentage calculations, etc. Please refer to the HA-2556 four quadrant multiplier data sheet for additional applications. MULTIPLIER, VOUT = VXVY / 5V SCALE FACTOR = 5V 1K FIGURE 3. SETTING THE SCALE FACTOR Typical Applications Automatic Gain Control In Figure 4 the HA-2546 is configured in a true Automatic Gain Control or AGC application. The HA-5127, low noise op amp, provides the gain control level to the X input. This level will set the peak output voltage of the multiplier to match the reference level. The feedback network around the HA-5127 8 FN2861.6 November 19, 2004 HA-2546 1 REF NC 2 NC 3 NC 4 X 5 + 6 V- 7 8 16 NC 15 100 80 60 VGAIN = 0.030V 0.126V 0.4V 14 13 12 11 V+ + 10 9 VOLTAGE GAIN (dB) 40 20 0 -20 -40 -60 0.902V 180 135 90 45 0 10K 100K 1M 10M 100M PHASE (DEGREES) + - - Y Σ- Z + -80 -100 1K FREQUENCY (Hz) 5kΩ 500Ω VIN VOUT + HFA0002 FIGURE 5. VOLTAGE CONTROLLED AMPLIFIER 1 REF NC NC NC Ch A 2 3 4 X 5 + 6 Ch B V7 8 + + 16 NC 15 14 13 VMIX (0V to 2V) 12 11 V+ 10 9 VOUT 50Ω - - Y Σ- Z + VOUT = Ch B + (Ch A - Ch B) VMIX / Scale Factor Scale Factor = 2 VOUT = All Ch B; if VMIX = 0V VOUT = All Ch A; if VMIX = 2V (Full Scale) VOUT = Mix of Ch A and Ch B; if 0V < VMIX < 2V FIGURE 6. VIDEO FADER 9 FN2861.6 November 19, 2004 HA-2546 Typical Performance Curves 9 6 GAIN (dB) 3 0 -3 -6 CL = 0pF 0 45 90 CL = 50pF 135 180 100M GAIN (dB) CL = 0pF PHASE SHIFT (DEGREES) RL = 1K, VX = 2VDC, VY = 200mVRMS CL = 50pF 15 RL = 1K, VX+ = 200mVRMS, VY = 5VDC, VX- = -1VDC 10 5 PHASE SHIFT (DEGREES) 0 -5 -10 0 45 90 135 10K 100K 1M FREQUENCY (Hz) 10M 180 100M VS = ±15V, TA = 25oC, See Test Circuit For Multiplier Configuration 10K 100K 1M FREQUENCY (Hz) 10M FIGURE 7. VY GAIN AND PHASE vs FREQUENCY FIGURE 8. VX GAIN AND PHASE vs FREQUENCY -10 -20 -30 GAIN (dB) -40 GAIN (dB) -50 -60 -70 -80 -90 VX = 0V, RL = 1K, VY = 200mVRMS 0 -10 -20 -30 -40 -50 VX = -0.5VDC VX = -1.0VDC VX = -2.0VDC RL = 1K, VX+ = 200mVRMS, VY = 0V 10K 100K 1M FREQUENCY (Hz) 10M 100M 10K 100K 1M FREQUENCY (Hz) 10M 100M FIGURE 9. VY FEEDTHROUGH vs FREQUENCY FIGURE 10. VX FEEDTHROUGH vs FREQUENCY 9 6 3 GAIN (dB) 0 -3 -6 -9 -12 -15 VX = 0.5VDC GAIN (dB) VX = 1.0VDC RL = 1K, CL = 50pF, VY = 200mVRMS VX = 2.0VDC 15 10 5 0 -5 -10 -15 -20 VX+ = 200mVRMS, RL = 1K, VX- = -1VDC VY = 5VDC VY = 2VDC VY = 1VDC VY = 0.5VDC 10K 100K 1M FREQUENCY (Hz) 10M 100M 10K 100K 1M FREQUENCY (Hz) 10M 100M FIGURE 11. VARIOUS VY FREQUENCY RESPONSES FIGURE 12. VARIOUS VX FREQUENCY RESPONSES 10 FN2861.6 November 19, 2004 HA-2546 Typical Performance Curves 975 900 825 750 675 600 525 450 375 300 225 150 75 0 1 10 100 1K 10K 100K FREQUENCY (Hz) VS = ±15V, TA = 25oC, See Test Circuit For Multiplier Configuration (Continued) 14 12 10 CURRENT (µA) 8 6 4 2 0 OFFSET CURRENT -2 -4 -55 BIAS CURRENT VOLTAGE NOISE (nV/√Hz) -25 0 25 50 75 100 125 TEMPERATURE (oC) FIGURE 13. VOLTAGE NOISE DENSITY FIGURE 14. VY OFFSET AND BIAS CURRENT vs TEMPERATURE 10 8 OFFSET VOLTAGE (mV) 6 4 2 0 -2 -4 -6 -8 -10 -55 -25 0 25 50 75 100 125 VZ CURRENT (µA) VY VX 3 2 BIAS CURRENT 1 OFFSET CURRENT 0 -1 -55 -25 0 25 50 75 100 125 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 15. OFFSET VOLTAGE vs TEMPERATURE FIGURE 16. VX OFFSET AND BIAS CURRENT vs TEMPERATURE 120 7 6 -VOUT 5 |VOUT| 4 3 2 1 0 ±17 ±15 ±12 VSUPPLY ±8 ±7 ±5 +VOUT CMRR (dB) 100 80 60 40 20 0 VYcm = 200mVRMS V X = 0V V X = 2V 100 1K 10K 100K 1M 10M 100M FREQUENCY (Hz) FIGURE 17. VOUT vs VSUPPLY FIGURE 18. VY CMRR vs FREQUENCY 11 FN2861.6 November 19, 2004 HA-2546 Typical Performance Curves 120 100 CMRR (dB) 80 60 40 20 0 V Y = 2V VY = 0V VX = 200mVRMS PSRR (dB) 100 80 60 40 20 0 -PSSR VS = ±15V, TA = 25oC, See Test Circuit For Multiplier Configuration (Continued) V Y = V X = 0V +PSSR 100 1K 10K 100K 1M 10M 100M 100 1K 10K 100K 1M 10M 100M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 19. VX COMMON MODE REJECTION RATIO vs FREQUENCY FIGURE 20. PSRR vs FREQUENCY 25 -ICC SUPPLY CURRENT (mA) 14 12 10 |CMR| +ICC 8 6 4 2 CMR(+) CMR(-) 20 15 -55 0 -25 0 25 50 75 100 125 TEMPERATURE (oC) ±17 ±15 ±12 VSUPPLY ±8 ±7 ±5 FIGURE 21. SUPPLY CURRENT vs TEMPERATURE FIGURE 22. CMR vs VSUPPLY 100 +PSRR 80 -PSRR PSRR (dB) 60 MULTIPLIER ERROR (%FS) 1.5 X=1 X = 1.2 1 X = 1.4 0.5 0 40 -0.5 X = 1.6 X = 1.8 X=2 -6 -4 -2 0 Y INPUT (V) 2 4 6 20 -1 0 -55 -1.5 -25 0 25 50 75 100 125 TEMPERATURE (oC) FIGURE 23. PSRR vs TEMPERATURE FIGURE 24. MULTIPLICATION ERROR vs VY 12 FN2861.6 November 19, 2004 HA-2546 Typical Performance Curves 2 1.5 MULTIPLIER ERROR (%FS) 1 X = 0.2 0.5 X=1 0 X=0 -0.5 -1 -1.5 -2 -6 -4 -2 0 Y INPUT (V) 2 4 6 X = 0.8 X = 0.4, 0.6 MULTIPLIER ERROR (%FS) VS = ±15V, TA = 25oC, See Test Circuit For Multiplier Configuration (Continued) 2 1.5 1 0.5 0 -0.5 -1 -1.5 0 0.5 1 1.5 2 2.5 X INPUT (V) Y = -2 Y = -1 Y=0 Y = -5 Y = -4 Y = -3 FIGURE 25. FIGURE 26. 1 0.5 0 -0.5 -1 -1.5 -2 Y=0 Y=1 MULTIPLICATION ERROR (%) 2 2.5 Y=2 Y=3 Y=4 Y=5 0 0.5 1 1.5 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 -55 MULTIPLIER ERROR (%FS) -25 0 25 50 75 100 125 X INPUT (V) TEMPERATURE (oC) FIGURE 27. FIGURE 28. WORST CASE MULTIPLICATION ERROR vs TEMPERATURE 0.5 0.6 MULTIPLICATION ERROR (%) 0.4 0.4 GAIN (dB) 0.3 CL = 50pF 0.2 RL = 1K, VX = 2VDC, VY = 200mVRMS 0.2 0 0.1 -0.2 0.0 -55 -25 0 25 50 75 100 125 10K 100K 1M FREQUENCY (Hz) 10M 100M CL = 0pF TEMPERATURE (oC) FIGURE 29. MULTIPLICATION ERROR vs TEMPERATURE FIGURE 30. GAIN VARIATION vs FREQUENCY 13 FN2861.6 November 19, 2004 HA-2546 Typical Performance Curves 2.010 7.0 2.008 PEAK OUTPUT VOLTAGE (V) 2.006 SCALE FACTOR 2.004 2.002 2.000 1.998 1.996 1.994 1.992 1.990 -55 -25 0 25 50 75 100 125 6.0 5.0 4.0 3.0 2.0 1.0 0.0 10 100 1K LOAD RESISTANCE (Ω) 10K 100K TEMPERATURE (oC) VS = ±8 fO = 10kHz, VX = 2VDC, THD < 0.1% VS = ±15 VS = ±12 VS = ±10 VS = ±15V, TA = 25oC, See Test Circuit For Multiplier Configuration (Continued) FIGURE 31. SCALE FACTOR vs TEMPERATURE FIGURE 32. OUTPUT VOLTAGE SWING vs LOAD RESISTANCE 500 24 22 20 18 16 14 12 10 8 6 4 2 0 -60 VY CHANNEL 400 SLEW RATE (V/µs) VY CHANNEL RISE TIME (ns) VX CHANNEL 300 200 VX CHANNEL 100 0 -60 -40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 33. SLEW RATE vs TEMPERATURE FIGURE 34. RISE TIME vs TEMPERATURE 28 26 24 SUPPLY CURRENT (mA) 22 20 18 16 14 12 10 8 6 4 2 0 2 4 6 8 10 12 14 16 18 20 SUPPLY VOLTAGE (±V) +ICC -ICC FIGURE 35. SUPPLY CURRENT vs SUPPLY VOLTAGE 14 FN2861.6 November 19, 2004 HA-2546 Die Characteristics DIE DIMENSIONS: 79.9 mils x 119.7 mils x 19 mils METALLIZATION: Type: Al, 1% Cul Thickness: 16kÅ ±2kÅ PASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos) Silox Thickness: 12kÅ ±2kÅ Nitride Thickness: 3.5kÅ ±2kÅ TRANSISTOR COUNT: 87 Metallization Mask Layout HA-2546 VREF GND 2 1 GA A GA C 16 15 VYIOB 3 14 GA B VYIOA 4 13 VX+ VY+ 5 12 VX- VY- 6 11 V+ 7 V- 8 VOUT 9 VZ+ 10 VZ- 15 FN2861.6 November 19, 2004 HA-2546 Small Outline Plastic Packages (SOIC) N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM M16.3 (JEDEC MS-013-AA ISSUE C) 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A L MILLIMETERS MIN 2.35 0.10 0.33 0.23 10.10 7.40 MAX 2.65 0.30 0.51 0.32 10.50 7.60 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93 MIN 0.0926 0.0040 0.013 0.0091 0.3977 0.2914 MAX 0.1043 0.0118 0.0200 0.0125 0.4133 0.2992 A1 B C D E α µ A1 0.10(0.004) C e H h L N 0.050 BSC 0.394 0.010 0.016 16 0o 8o 0.419 0.029 0.050 1.27 BSC 10.00 0.25 0.40 16 0o 10.65 0.75 1.27 e B 0.25(0.010) M C AM BS NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. α All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 FN2861.6 November 19, 2004