HA-5033_06

® HA-5033 Data Sheet February 6, 2006 FN2924.8 250MHz Video Buffer The HA-5033 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 250MHz and outstanding differential phase/ gain characteristics, this high performance voltage follower is an excellent choice for video circuit design. Other features, which include a minimum slew rate of 1000V/µs and high output drive capability, make the HA-5033 applicable for line driver and high speed data conversion circuits. The high performance of this product is a result of the Intersil Dielectric Isolation process. A major feature of this process is that it produces both PNP and NPN high frequency transistors which makes wide bandwidth designs, such as the HA-5033, practical. Alternative process methods typically produce a lower AC performance. Features • Differential Phase Error . . . . . . . . . . . . . . . . 0.02 Degrees • Differential Gain Error . . . . . . . . . . . . . . . . . . . . . . 0.03% • High Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . 1100V/µs • Wide Bandwidth (Small Signal) . . . . . . . . . . . . . . 250MHz • Wide Power Bandwidth . . . . . . . . . . . . . . DC to 17.5MHz • Fast Rise Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3ns • High Output Drive. . . . . . . . . . . . . . ±10V With 100Ω Load • Wide Power Supply Range . . . . . . . . . . . . . ±5V to ±16V • Replace Costly Hybrids Applications • Video Buffer • High Frequency Buffer Ordering Information PART NUMBER PART MARKING TEMP. RANGE (°C) -55 to 125 0 to 75 PACKAGE PKG. DWG. # • Isolation Buffer • High Speed Line Driver • Impedance Matching • Current Boosters HA2-5033-2 HA2-5033-2 HA3-5033-5 HA3-5033-5 12 Pin Metal Can T12.C 8 Ld PDIP E8.3 Pinouts HA-5033 (PDIP) TOP VIEW V+ 1 NC NC IN 2 3 4 8 7 6 5 OUT NC SUBSTRATE V- • High Speed A/D Input Buffers • Related Literature - AN548, Designer’s Guide for HA-5033 HA-5033 (METAL CAN) TOP VIEW V+ NC CASE 2 NC NC 3 4 5 6 +IN NC NC 7 8 NC 1 12 11 10 9 VNC OUT 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003, 2005, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HA-5033 Absolute Maximum Ratings Voltage Between V+ and V- Pins. . . . . . . . . . . . . . . . . . . . . . . . 40V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current (Peak) (50ms On/1 Second Off) . . . . . . . . . ±200mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 2000V Thermal Information Thermal Resistance (Typical, Note 2) θJA (°C/W) θJC (°C/W) Metal Can Package . . . . . . . . . . . . . . . 65 34 PDIP Package . . . . . . . . . . . . . . . . . . . 120 N/A Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C Maximum Junction Temperature (Plastic Packages) . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C Operating Conditions Temperature Ranges (Note 3) HA-5033-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to 125°C HA-5033-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 75°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including load conditions, must be designed to maintain the maximum junction temperature below 175°C for the metal can package, and below 150°C for the plastic packages (See Figure 5.). 2. θJA is measured with the component mounted on an evaluation PC board in free air. 3. The maximum operating temperature may have to be derated depending on the output load condition. See Figure 5 for more information. Electrical Specifications PARAMETER INPUT CHARACTERISTICS Offset Voltage VSUPPLY = ±12V, RS = 50Ω , RL = 100Ω, CL = 10pF, Unless Otherwise Specified TEST CONDITIONS TEMP. (°C) HA-5033-2 MIN TYP MAX MIN HA-5033-5 TYP MAX UNITS 25 Full - 5 6 33 20 30 3 1.6 20 15 25 35 50 - - 5 6 33 20 30 3 1.6 20 15 25 35 50 - mV mV µV/°C µA µA MΩ pF µVP-P Average Offset Voltage Drift Bias Current Full 25 Full Input Resistance Input Capacitance Input Noise Voltage TRANSFER CHARACTERISTICS Voltage Gain RL = 100Ω R L = 1k Ω RL = 100Ω -3dB Bandwidth OUTPUT CHARACTERISTICS Output Voltage Swing RL = 100Ω RL = 1kΩ , VS = ±15V Output Current Output Resistance Full Power Bandwidth Full Power Bandwidth (Note 4) TRANSIENT RESPONSE Rise Time Propagation Delay VOUT = 500mV VOUT = 1VRMS , RL = 1kΩ 10Hz to 100MHz 25 25 25 25 25 Full 25 0.93 0.93 0.92 - 0.99 250 - 0.93 0.93 0.92 - 0.99 250 - V/V V/V V/V MHz Full Full 25 25 25 25 ±8 ±11 ±80 15.9 ±10 ±12 ±100 8 146 17.5 - ±8 ±11 ±80 15.9 ±10 ±12 ±100 8 146 17.5 - V V mA Ω MHz MHz 25 25 - 4.6 1 - - 4.6 1 - ns ns 2 FN2924.8 HA-5033 Electrical Specifications PARAMETER Overshoot Slew Rate (Note 4) Settling Time to 0.1% Differential Phase Error (Note 5) Differential Gain Error (Note 5) POWER SUPPLY CHARACTERISTICS Supply Current 25 Full Power Supply Rejection Ratio Harmonic Distortion NOTES: 4. VSUPPLY = ±15V, VOUT = ±10V, RL = 1kΩ. 5. Differential gain and phase error are nonlinear signal distortions found in video systems and are defined as follows: Differential gain error is defined as the change in amplitude at the color subcarrier frequency as the picture signal is varied from blanking to white level. Differential phase error is defined as the change in the phase of the color subcarrier as the picture signal is varied from blanking to white level. RL = 300Ω. VIN = 1VRMS at 100kHz Full 25 54 21 21