HA2-5033-2

HA-5033 Data Sheet September 1998 File Number 2924.4 250MHz Video Buffer The HA-5033 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 250MHz and outstanding differential phase/ gain characteristics, this high performance voltage follower is an excellent choice for video circuit design. Other features, which include a minimum slew rate of 1000V/µs and high output drive capability, make the HA-5033 applicable for line driver and high speed data conversion circuits. The high performance of this product is a result of the Intersil Dielectric Isolation process. A major feature of this process is that it produces both PNP and NPN high frequency transistors which makes wide bandwidth designs, such as the HA-5033, practical. Alternative process methods typically produce a lower AC performance. Features • Differential Phase Error . . . . . . . . . . . . . . . 0.02 Degrees • Differential Gain Error. . . . . . . . . . . . . . . . . . . . . . . 0.03% • High Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . 1100V/µs • Wide Bandwidth (Small Signal) . . . . . . . . . . . . . . 250MHz • Wide Power Bandwidth . . . . . . . . . . . . . . DC to 17.5MHz • Fast Rise Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3ns • High Output Drive. . . . . . . . . . . . . . ±10V With 100Ω Load • Wide Power Supply Range. . . . . . . . . . . . . . ±5V to ±16V • Replace Costly Hybrids Applications • Video Buffer • High Frequency Buffer Ordering Information PART NUMBER (BRAND) HA2-5033-2 HA2-5033-5 HA3-5033-5 HA4P5033-5 HA9P5033-5 (H50335) TEMP. RANGE (oC) -55 to 125 0 to 75 0 to 75 0 to 75 0 to 60 (Note 3) PACKAGE 12 Pin Metal Can 12 Pin Metal Can 8 Ld PDIP 20 Ld PLCC 8 Ld PSOP PKG. NO. T12.C T12.C E8.3 N20.35 M8.15A • Isolation Buffer • High Speed Line Driver • Impedance Matching • Current Boosters • High Speed A/D Input Buffers • Related Literature - AN548, Designer’s Guide for HA-5033 Pinouts HA-5033 (PDIP, PSOP) TOP VIEW NC HA-5033 (PLCC) TOP VIEW OUT NC NC V+ HA-5033 (METAL CAN) TOP VIEW V+ NC CASE 1 2 NC NC 3 4 5 6 +IN NC NC 7 8 NC 12 11 10 9 VNC OUT V+ 1 NC NC IN 2 3 4 8 7 6 5 OUT NC NC 4 SUBSTRATE VNC 5 NC 6 NC 7 NC 8 3 2 1 20 19 18 NC 17 NC 16 NC 15 SUBSTRATE 14 NC 9 NC 10 IN 11 NC 12 V- 13 NC 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 HA-5033 Absolute Maximum Ratings Voltage Between V+ and V- Pins . . . . . . . . . . . . . . . . . . . . . . . . 40V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current (Peak) (50ms On/1 Second Off) . . . . . . . . . ±200mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 2000V Thermal Information Thermal Resistance (Typical, Note 2) θJA (oC/W) θJC (oC/W) Metal Can Package . . . . . . . . . . . . . . . 65 34 PDIP Package . . . . . . . . . . . . . . . . . . . 96 N/A PSOP Package (Note 4) . . . . . . . . . . . 129 N/A PLCC Package. . . . . . . . . . . . . . . . . . . 80 N/A Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . .175oC Maximum Junction Temperature (Plastic Packages) . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (PSOP and PLCC - Lead Tips Only) Operating Conditions Temperature Ranges HA-5033-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC HA-5033-5 (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC HA9P5033-5 (Notes 1, 3) . . . . . . . . . . . . . . . . . . . . -40oC to 60oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including load conditions, must be designed to maintain the maximum junction temperature below 175oC for the metal can package, and below 150oC for the plastic packages (See Figure 5.). 2. θJA is measured with the component mounted on an evaluation PC board in free air. 3. Maximum operating temperature in the PSOP package is limited to 60oC, for VSUPPLY = ±12V to prevent the junction temperature from exceeding 150oC. The maximum operating temperature may have to be derated further, depending on the output load condition. The operating temperature may be increased if the HA9P5033 is operated at lower VSUPPLY. For example, the quiescent operating temperature may be increased to 75oC by operating at VSUPPLY ≤ ±9.7V. See Figure 5 for more information. 4. Direct attach of the PSOP copper slug to copper area on the PCB can reduce the θJA value to