HA4344B

® HA4344B Data Sheet June 1, 2006 FN3956.4 350MHz, 4x1 Video Crosspoint Switch with Synchronous Controls The HA4344B is a very wide bandwidth 4x1 crosspoint switch ideal for professional video switching, HDTV, computer display routing, and other high performance applications. This circuit features very low power dissipation, excellent differential gain and phase, high off isolation, symmetric slew rates, fast switching, and latched control signals. When disabled, the output is switched to a high impedance state, making the HA4344B ideal for matrix routers. The latched control signals allow for synchronized channel switching. When CK1 is low, the master control latch loads the next switching address (A0, A1, CS), while the closed (assuming CK2 is the inverse of CK1) slave control latch maintains the crosspoint in its current state. CK2 switching low closes the master latch (with previous assumption), loads the now open slave latch, and switches the crosspoint to the newly selected channel. Channel selection is asynchronous (changes with any control signal change) if both CK1 and CK2 are low. Features • Low Power Dissipation . . . . . . . . . . . . . . . . . . . . . .105mW • Symmetrical Slew Rates . . . . . . . . . . . . . . . . . . 1400V/μs • 0.1dB Gain Flatness. . . . . . . . . . . . . . . . . . . . . . . 100MHz • -3dB Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . 350MHz • Off Isolation (100MHz) . . . . . . . . . . . . . . . . . . . . . . . .70dB • Crosstalk Rejection (30MHz) . . . . . . . . . . . . . . . . . . .80dB • Differential Gain and Phase . . . . . . . . . . . . . . 0.01%/0.01° • High ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . .>2000V • TTL Compatible Control Signals • Latched Control Lines for Synchronous Switching • Pb-Free Plus Anneal Available (RoHS Compliant) Applications • Professional Video Switching and Routing • RGB Video Distribution Systems • Computer Graphics • RF Switching and Routing Ordering Information PART NUMBER HA4344BCB HA4344BCBZ (Note) PART TEMP. RANGE PKG. MARKING (°C) PACKAGE DWG. # HA4344BCB 4344BCBZ 0 to 70 0 to 70 0 to 70 16 Ld SOIC M16.15 16 Ld SOIC M16.15 (Pb-free) 16 Ld SOIC M16.15 Tape & Reel (Pb-free) Pinout IN0 GND IN1 GND HA4344B (SOIC) TOP VIEW 1 2 3 4 5 6 7 8 16 V+ 15 A0 14 A1 13 CS 12 OUT 11 CK2 10 CK1 9 V- HA4344BCBZ96 4344BCBZ (Note) NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. IN2 GND IN3 GND Functional Diagram EN0 DL Q C DL Q C DECODE EN2 DL Q C DL Q C DL Q C DL Q C DL Q C DL Q C IN0 IN1 IN2 IN3 OUT Timing Diagram CK1 CK2 A0, A1, CS OUT CHX CHY CHZ CHX CHZ EN1 A0 A1 CS EN3 CK1 CK2 100kΩ CHX CHY CHX CHZ 100kΩ 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HA4344B Absolute Maximum Ratings Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY Digital Input Current (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . ±25mA Analog Input Current (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . ±5mA Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . .2000V Thermal Information Thermal Resistance (Typical, Note 1) θJA (°C/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . . 175°C Maximum Junction Temperature (Plastic Package) . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief 379 for details. 2. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values. Electrical Specifications PARAMETER VSUPPLY = ±5V, RL = 10kΩ, VCS = 0.8V, Unless Otherwise Specified TEST CONDITIONS (NOTE 4) TEMP. (°C) MIN TYP MAX UNITS DC SUPPLY CHARACTERISTICS Supply Voltage Supply Current (VOUT = 0V) VCS = 0.8V VCS = 0.8V VCS = 2.0V VCS = 2.0V ANALOG DC CHARACTERISTICS Output Voltage Swing Without Clipping VOUT = VIN ±VIO ±20mV 25, 70 0 Output Current Input Bias Current Output Offset Voltage Output Offset Voltage Drift (Note 3) SWITCHING CHARACTERISTICS Turn-On Time Turn-Off Time Output Glitch During Switching DIGITAL DC CHARACTERISTICS Input Logic High Voltage Input Logic Low Voltage CLK1, CLK2 Input Current CS, A0, A1 Input Current AC CHARACTERISTICS Insertion Loss 1VP-P 25 Full Channel-to-Channel Insertion Loss Match Full 0.055 0.07 ±0.004 0.063 0.08 ±0.006 dB dB dB 0 to 4V 0 to 4V Full Full Full Full 2 -2 40 0.8 50 2 V V μA μA 25 25 25 160 320 ±10 ns ns mV Full Full Full Full ±2.7 ±2.4 15 -10 ±2.8 ±2.5 20 30 25 50 10 50 V V mA μA mV μV/°C Full 25, 70 0 25, 70 0 ±4.5 ±5.0 10.5 400 400 ±5.5 13 15.5 450 580 V mA mA μA μA 2 FN3956.4 June 1, 2006 HA4344B Electrical Specifications PARAMETER -3dB Bandwidth VSUPPLY = ±5V, RL = 10kΩ, VCS = 0.8V, Unless Otherwise Specified (Continued) TEST CONDITIONS RS = 47Ω, CL = 10pF RS = 29Ω, CL = 20pF RS = 16Ω, CL = 33pF RS = 9Ω, CL = 52pF ±0.1dB Flat Bandwidth RS = 47Ω, CL = 10pF RS = 29Ω, CL = 20pF RS = 16Ω, CL = 33pF RS = 9Ω, CL = 52pF Input Resistance Input Capacitance Enabled Output Resistance Disabled Output Capacitance Differential Gain Differential Phase Off Isolation Crosstalk Rejection Slew Rate (1.5VP-P, +SR/-SR) VCS = 2.0V 4.43MHz (Note 3) 4.43MHz (Note 3) 1VP-P , 100MHz, VCS = 2.0V 1VP-P, 30MHz RS = 47Ω, CL = 10pF RS = 29Ω, CL = 20pF RS = 16Ω, CL = 33pF RS = 9Ω, CL = 52pF Total Harmonic Distortion (Note 3) Disabled Output Resistance NOTES: 3. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation. 4. Units are 100% tested at 25°C; guaranteed, but not tested at 0°C and 70°C. VCS = 2.0V (NOTE 4) TEMP. (°C) 25 25 25 25 25 25 25 25 Full Full Full Full 25 25 Full Full 25 25 25 25 Full Full MIN 200 TYP 350 300 220 160 150 110 100 70 400 1.5 15 2.5 0.01 0.01 70 80 1400/1490 1200/1260 870/940 750/710 0.01 12 MAX 0.02 0.02 0.1 UNITS MHz MHz MHz MHz MHz MHz MHz MHz kΩ pF Ω pF % ° dB dB V/μs V/μs V/μs V/μs % MΩ AC Test Circuit 500Ω 400Ω 510Ω HA4344B VIN 75Ω RS CX 10kΩ + HFA1100 75Ω VOUT NOTE: CL = CX + Test Fixture Capacitance. 3 FN3956.4 June 1, 2006 HA4344B Small Outline Plastic Packages (SOIC) N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45° H 0.25(0.010) M BM M16.15 (JEDEC MS-012-AC ISSUE C) 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A L MILLIMETERS MIN 1.35 0.10 0.33 0.19 9.80 3.80 MAX 1.75 0.25 0.51 0.25 10.00 4.00 NOTES 9 3 4 5 6 7 8° Rev. 1 6/05 MIN 0.0532 0.0040 0.013 0.0075 0.3859 0.1497 MAX 0.0688 0.0098 0.020 0.0098 0.3937 0.1574 A1 B C D E α A1 0.10(0.004) C e H h L N 0.050 BSC 0.2284 0.0099 0.016 16 0° 8° 0.2440 0.0196 0.050 1.27 BSC 5.80 0.25 0.40 16 0° 6.20 0.50 1.27 e B 0.25(0.010) M C AM BS NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. α All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 4 FN3956.4 June 1, 2006