HA5002

HA-5002 Data Sheet November 1998 File Number 2921.4 110MHz, High Slew Rate, High Output Current Buffer The HA-5002 is a monolithic, wideband, high slew rate, high output current, buffer amplifier. Utilizing the advantages of the Intersil D.I. technologies, the HA-5002 current buffer offers 1300V/µs slew rate with 110MHz of bandwidth. The ±200mA output current capability is enhanced by a 3Ω output impedance. The monolithic HA-5002 will replace the hybrid LH0002 with corresponding performance increases. These characteristics range from the 3000kΩ input impedance to the increased output voltage swing. Monolithic design technologies have allowed a more precise buffer to be developed with more than an order of magnitude smaller gain error. The HA-5002 will provide many present hybrid users with a higher degree of reliability and at the same time increase overall circuit performance. For the military grade product, refer to the HA-5002/883 datasheet, AnswerFAX document #3705. Features • • • • • • • • Voltage Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.995 High Input Impedance . . . . . . . . . . . . . . . . . . . . . 3000kΩ Low Output Impedance . . . . . . . . . . . . . . . . . . . . . . . . 3Ω Very High Slew Rate . . . . . . . . . . . . . . . . . . . . . 1300V/µs Very Wide Bandwidth . . . . . . . . . . . . . . . . . . . . . . 110MHz High Output Current . . . . . . . . . . . . . . . . . . . . . . . ±200mA Pulsed Output Current . . . . . . . . . . . . . . . . . . . . . . 400mA Monolithic Construction Applications • • • • Line Driver Data Acquisition 110MHz Buffer Radar Cable Driver • • • • High Power Current Booster High Power Current Source Sample and Holds Video Products Ordering Information PART NUMBER (BRAND) HA2-5002-2 HA2-5002-5 HA3-5002-5 HA4P5002-5 HA7-5002-2 HA7-5002-5 HA9P5002-5 (H50025) HA9P5002-9 (H50029) TEMP. RANGE (oC) -55 to 125 0 to 75 0 to 75 0 to 75 -55 to 125 0 to 75 0 to 75 -40 to 85 PACKAGE 8 Pin Metal Can 8 Pin Metal Can 8 Ld PDIP 20 Ld PLCC 8 Ld CERDIP 8 Ld CERDIP 8 Ld SOIC 8 Ld SOIC PKG. NO. T8.C T8.C E8.3 N20.35 F8.3A F8.3A M8.15 M8.15 Pinouts HA-5002 (PDIP, CERDIP, SOIC) TOP VIEW HA-5002 (PLCC) TOP VIEW OUT V1+ NC NC NC HA-5002 (METAL CAN) TOP VIEW IN 8 V1+ 1 7 V1- V1+ V2NC IN 1 2 3 4 8 7 6 5 OUT V2+ NC 4 NC V1V2- 5 NC 6 NC 7 NC 8 3 2 1 20 19 18 NC 17 V2+ 16 NC 15 NC 14 NC 9 NC 10 IN 11 NC 12 V113 NC NC 3 4 OUT 5 NC V2+ 2 6 V2- NOTE: Case Voltage = Floating 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 HA-5002 Absolute Maximum Ratings Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 44V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V1+ to V1Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . ±200mA Output Current (50ms On, 1s Off) . . . . . . . . . . . . . . . . . . . . ±400mA Thermal Information Thermal Resistance (Typical, Note 2) θJA (oC/W)θJC (oC/W) CERDIP Package. . . . . . . . . . . . . . . . . 115 28 PDIP Package . . . . . . . . . . . . . . . . . . . 92 N/A Metal Can Package . . . . . . . . . . . . . . . 155 67 PLCC Package. . . . . . . . . . . . . . . . . . . 74 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 157 N/A Max Junction Temperature (Hermetic Packages, Note 1) . . . . . . 175oC Max Junction Temperature (Plastic Packages, Note 1) . . . . . . . . 150oC Max Storage Temperature Range . . . . . . . . . . . . . . -65oC to 150oC Max Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . 300oC (PLCC and SOIC - Lead Tips Only) Operating Conditions Temperature Range HA-5002-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC HA-5002-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC HA-5002-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including load conditions, must be designed to maintain the maximum junction temperature below 175oC for the ceramic and can packages, and below 150oC for the plastic packages. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications PARAMETER INPUT CHARACTERISTICS Offset Voltage VSUPPLY = ±12V to ±15V, RS = 50Ω, RL = 1kΩ, CL = 10pF, Unless Otherwise Specified TEST CONDITIONS TEMP (oC) HA-5002-2 MIN TYP MAX MIN HA-5002-5, -9 TYP MAX UNITS 25 Full 1.5 - 5 10 30 2 3.4 3 18 20 30 7 10 - 1.5 - 5 10 30 2 2.4 3 18 20 30 7 10 - mV mV µV/οC µA µA MΩ µVP-P V/V V/V V/V V/V MHz A/mA Average Offset Voltage Drift Bias Current Full 25 Full Input Resistance Input Noise Voltage TRANSFER CHARACTERISTICS Voltage Gain (VOUT = ±10V) RL = 50Ω RL = 100Ω RL = 1kΩ RL = 1kΩ -3dB Bandwidth AC Current Gain OUTPUT CHARACTERISTICS Output Voltage Swing RL = 100Ω RL = 1kΩ, VS = ±15V RL = 1kΩ, VS = ±12V Output Current Output Resistance Harmonic Distortion TRANSIENT RESPONSE Full Power Bandwidth (Note 3) Rise Time Propagation Delay Overshoot Slew Rate Settling Time Differential Gain Differential Phase To 0.1% RL = 500Ω RL = 500Ω VIN = 1VRMS, f = 10kHz VIN = ±10V, RL = 40Ω VIN = 1VP-P 10Hz-1MHz Full 25 25 25 25 Full 25 25 0.980 ±10 ±10 ±10 - 0.900 0.971 0.995 110 40 ±10.7 ±13.5 ±10.5 220 3