HA7210

® NOT D MMEN RECO S ESIGN N EW D R ED F O HA7210 August 5, 2005 FN3389.11 Data Sheet 10kHz to 10MHz, Low Power Crystal Oscillator The HA7210 is a very low power crystal-controlled oscillators that can be externally programmed to operate between 10kHz and 10MHz. For normal operation it requires only the addition of a crystal. The part exhibits very high stability over a wide operating voltage and temperature range. The HA7210 also features a disable mode that switches the output to a high impedance state. This feature is useful for minimizing power dissipation during standby and when multiple oscillator circuits are employed. Features • Single Supply Operation at 32kHz . . . . . . . . . . . . 2V to 7V • Operating Frequency Range . . . . . . . . . .10kHz to 10MHz • Supply Current at 32kHz . . . . . . . . . . . . . . . . . . . . . . .5µA • Supply Current at 1MHz. . . . . . . . . . . . . . . . . . . . . .130µA • Drives 2 CMOS Loads • Only Requires an External Crystal for Operation • Pb-Free Plus Anneal Available (RoHS Compliant) Ordering Information PART NUMBER (BRAND) HA7210IP HA7210IB (H7210I) HA7210IBZ (7210IBZ) (Note) HA7210IBZ96 (7210IBZ) (Note) TEMP. RANGE (°C) -40 to 85 -40 to 85 -40 to 85 -40 to 85 PACKAGE 8 Ld PDIP 8 Ld SOIC 8 Ld SOIC (Pb-free) 8 Ld SOIC (Pb-free) Tape and Reel PKG. DWG. # E8.3 M8.15 M8.15 M8.15 Applications • Battery Powered Circuits • Remote Metering • Embedded Microprocessors • Palm Top/Notebook PC • Related Literature - AN9334, Improving HA7210 Start-Up Time Typical Application Circuit 0.1µF VDD NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 2 32.768kHz CRYSTAL HA7210 3 4 8 7 6 5 32.768kHz CLOCK (NOTE 1) Pinout HA7210 (PDIP, SOIC) TOP VIEW NOTE: VDD OSC IN OSC OUT VSS 1 2 3 4 8 7 6 5 ENABLE FREQ 2 FREQ 1 OUTPUT 32.768kHz MICROPOWER CLOCK OSCILLATOR 1. Internal pull-up resistors provided on EN, FREQ1, and FREQ2 inputs. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 1999-2005. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. HA7210 Simplified Block Diagram 1 8 ENABLE EXTERNAL CRYSTAL VDD (NOTE 2) OSC IN 2 RF 3 OSC OUT VDD 15pF S1B VDD S1C 15pF VDD VDD VDD - 1.4V VDD - 2.2V VDD - 3.0V VDD - 3.8V IBIAS VDD (NOTE 2) 6 FREQ 1 VDD (NOTE 2) 7 FREQ 2 S1A S2 S3 S4 BUFFER AMP 1 OF 4 DECODE VRN + OUTPUT LEVEL SHIFTER VRN 4 VSS 5 BUFFER - VDD P IN RF P N VRN OSCILLATOR OUT FREQUENCY SELECTION TRUTH TABLE ENABLE 1 1 1 1 0 NOTE: 2. Logic input pull-up resistors are constant current source of 0.4µA. FREQ 1 1 1 0 0 X FREQ 2 1 0 1 0 X SWITCH S1A, S1B, S1C S2 S3 S4 X OUTPUT RANGE 10kHz - 100kHz 100kHz - 1MHz 1MHz - 5MHz 5MHz - 10MHz+ High Impedance 2 HA7210 Absolute Maximum Ratings Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V Voltage (Any Pin) . . . . . . . . . . . . . . . . . . . . VSS -0.3V to VDD +0.3V ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . .4000V Thermal Information Thermal Resistance (Typical, Note 4) θJA (oC/W) Operating Conditions Temperature Range (Note 3). . . . . . . . . . . . . . . . . . . -40oC to 85oC PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 3. This product is production tested at 25oC only. 4. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications PARAMETER VDD Supply Range IDD Supply Current VSS = GND, TA = 25oC, Unless Otherwise Specified VDD = 5V TEST CONDITIONS fOSC = 32kHz fOSC = 32kHz, EN = 0 (Standby) fOSC = 32kHz, CL = 10pF (Note 5), EN = 1, Freq1 = 1, Freq2 = 1 fOSC = 32kHz, CL = 40pF, EN = 1, Freq1 = 1, Freq2 = 1 fOSC = 1MHz, CL = 10pF (Note 5), EN = 1, Freq1 = 0, Freq2 = 1 fOSC = 1MHz, CL = 40pF, EN = 1, Freq1 = 0, Freq2 = 1 MIN 2 4.0 5.0 2.0 CL = 18pF, RL = 1kΩ CL = 18pF, RL = 1kΩ 10% - 90%, fOSC = 32kHz, CL = 40pF 10% - 90%, fOSC = 32kHz, CL = 40pF CL = 40pF, fOSC = 1MHz CL = 40pF, fOSC = 32kHz fOSC = 32kHz, VDD = 5V, CL = 10pF fOSC = 32kHz, VDD = 5V, CL = 10pF fOSC = 32kHz, VDD = 5V, CL = 10pF 40 TYP 5 5.0 5.2 10 130 270 4.9 0.07 -10 10.0 0.1 10 0.4 800 90 12 12 54 41 1 0.1 0.01 MAX 7 9.0 10.2 15 200 350 0.4 -5 1.0 0.8 25 25 60 MIN VDD = 3V TYP 3.6 6.5 90 180 2.8 0.1 12 14 44 MAX 6.1 9 180 270 UNITS V µA µA µA µA µA V V mA mA nA nA µA V V ns ns ns ns % % ppm/V ppm/oC ppm/pF VOH Output High Voltage VOL Output Low Voltage IOH Output High Current IOL Output Low Current Three-State Leakage Current IOUT = -1mA IOUT = 1mA VOUT ≥ 4V VOUT ≤ 0.4V VOUT = 0V, 5V, TA = 25oC, -40oC VOUT = 0V, 5V, TA = 85oC VIN = VSS to VDD IIN Enable, Freq1, Freq2 Input Current VIH Input High Voltage Enable, Freq1, Freq2 VIL Input Low Voltage Enable, Freq1, Freq2 Enable Time Disable Time tr Output Rise Time tf Output Fall Time Duty Cycle, Packaged Part Only (Note 6) Duty Cycle, (See Typical Curves) Frequency Stability vs Supply Voltage Frequency Stability vs Temperature Frequency Stability vs Load NOTES: 5. Calculated using the equation IDD = IDD (No Load) + (VDD) (fOSC)(CL) 6. Duty cycle will vary with supply voltage, oscillation frequency, and parasitic capacitance on the crystal pins. 3 HA7210 Test Circuit 0.1µF 1VP-P +5V 1 2 50Ω 1000pF 3 4 HA7210 8 ENABLE 7 FREQ 2 6 FREQ 1 5 CL VOUT 18pF voltage of the oscillator section reduces power consumption and limits transconductance and bandwidth to the frequency range selected. For frequencies at the edge of a range, the higher range may provide better performance. The OSC OUT waveform on pin 3 is squared up through a series of inverters to the output drive stage. The Enable function is implemented with a NAND gate in the inverter string, gating the signal to the level shifter and output stage. Also during Disable the output is set to a high impedance state useful for minimizing power during standby and when multiple oscillators are OR’ed to a single node. FIGURE 1. In production the HA7210 is tested with a 32kHz and a 1MHz crystal. However for characterization purposes data was taken using a sinewave generator as the frequency determining element, as shown in Figure 1. The 1VP-P input is a smaller amplitude than what a typical crystal would generate so the transitions are slower. In general the Generator data will show a “worst case” number for IDD , duty cycle, and rise/fall time. The Generator test method is useful for testing a variety of frequencies quickly and provides curves which can be used for understanding performance trends. Data for the HA7210 using crystals has also been taken. This data has been overlaid onto the generator data to provide a reference for comparison. Design Considerations The low power CMOS transistors are designed to consume power mostly during transitions. Keeping these transitions short requires a good decoupling capacitor as close as possible to the supply pins 1 and 4. A ceramic 0.1µF is recommended. Additional supply decoupling on the circuit board with 1µF to 10µF will further reduce overshoot, ringing and power consumption. The HA7210, when compared to a crystal and inverter alone, will speed clock transition times, reducing power consumption of all CMOS circuitry run from that clock. Power consumption may be further reduced by minimizing the capacitance on moving nodes. The majority of the power will be used in the output stage driving the load. Minimizing the load and parasitic capacitance on the output, pin 5, will play the major role in minimizing supply current. A secondary source of wasted supply current is parasitic or crystal load capacitance on pins 2 and 3. The HA7210 is designed to work with most available crystals in its frequency range with no external components required. Two 15pF capacitors are internally switched onto crystal pins 2 and 3 on the HA7210 to compensate the oscillator in the 10kHz to 100kHz frequency range. The supply current of the HA7210 may be approximately calculated from the equation: IDD = IDD(Disabled) + VDD × fOSC × CL where: IDD = Total supply current VDD = Total voltage from VDD (pin 1) to VSS (pin 4) fOSC = Frequency of Oscillation CL = Output (pin 5) load capacitance EXAMPLE #1: VDD = 5V, fOSC = 100kHz, CL = 30pF IDD(Disabled) = 4.5µA (Figure 10) IDD = 4.5µA + (5V)(100kHz)(30pF) = 19.5µA Measured IDD = 20.3µA EXAMPLE #2: VDD = 5V, fOSC = 5MHz, CL = 30pF IDD (Disabled) = 75µA (Figure 9) IDD = 75µA + (5V)(5MHz)(30pF) = 825µA Measured IDD = 809µA Application Information Theory Of Operation The HA7210 is a Pierce Oscillator optimized for low power consumption, requiring no external components except for a bypass capacitor and a Parallel Mode Crystal. The Simplified Block Diagram shows the Crystal attached to pins 2 and 3, the Oscillator input and output. The crystal drive circuitry is detailed showing the simple CMOS inverter stage and the P-channel device being used as biasing resistor RF . The inverter will operate mostly in its linear region increasing the amplitude of the oscillation until limited by its transconductance and voltage rails, VDD and VRN. The inverter is self biasing using RF to center the oscillating waveform at the input threshold. Do not interfere with this bias function with external loads or excessive leakage on pin 2. Nominal value for RF is 17MΩ in the lowest frequency range to 7MΩ in the highest frequency range. The HA7210 optimizes its power for 4 frequency ranges selected by digital inputs Freq1 and Freq2 as shown in the Block Diagram. Internal pull up resistors (constant current 0.4µA) on Enable, Freq1 and Freq2 allow the user simply to leave one or all digital inputs not connected for a corresponding “1” state. All digital inputs may be left open for 10kHz to 100kHz operation. A current source develops 4 selectable reference voltages through series resistors. The selected voltage, VRN , is buffered and used as the negative supply rail for the oscillator section of the circuit. The use of a current source in the reference string allows for wide supply variation with minimal effect on performance. The reduced operating 4 HA7210 Crystal Selection For general purpose applications, a Parallel Mode Crystal is a good choice for use with the HA7210. However for applications where a precision frequency is required, the designer needs to consider other factors. Crystals are available in two types or modes of oscillation, Series and Parallel. Series Mode crystals are manufactured to operate at a specified frequency with zero load capacitance and appear as a near resistive impedance when oscillating. Parallel Mode crystals are manufactured to operate with a specific capacitive load in series, causing the crystal to operate at a more inductive impedance to cancel the load capacitor. Loading a crystal with a different capacitance will “pull” the frequency off its value. The HA7210 has 4 operating frequency ranges. The higher three ranges do not add any loading capacitance to the oscillator circuit. The lowest range, 10kHz to 100kHz, automatically switches in two 15pF capacitors onto OSC IN and OSC OUT to eliminate potential start-up problems. These capacitors create an effective crystal loading capacitor equal to the series combination of these two capacitors. For the HA7210 in the lowest range, the effective loading capacitance is 7.5pF. Therefore the choice for a crystal, in this range, should be a Parallel Mode crystal that requires a 7.5pF load. In the higher 3 frequency ranges, the capacitance on OSC IN and OSC OUT will be determined by package and layout parasitics, typically 4 to 5pF. Ideally the choice for crystal should be a Parallel Mode set for 2.5pF load. A crystal manufactured for a different load will be “pulled” from its nominal frequency (see Crystal Pullability). +5V C1 HA7210 C2 2 XTAL OSC IN C3 3 OSC OUT + 1 VDD frequency. In Method two these two goals can be at odds with each other; either the oscillator is trimmed to frequency by de-tuning the load circuit, or stability is increased at the expense of absolute frequency accuracy. Method one allows these two conditions to be met independently. The two fixed capacitors, C1 and C2 , provide the optimum load to the oscillator and crystal. C3 adjusts the frequency at which the circuit oscillates without appreciably changing the load (and thus the stability) of the system. Once a value for C3 has been determined for the particular type of crystal being used, it could be replaced with a fixed capacitor. For the most precise control over oscillator frequency, C3 should remain adjustable. This three capacitor tuning method will be more accurate and stable than method two and is recommended for 32kHz tuning fork crystals; without it they may leap into an overtone mode when power is initially applied. Method two has been used for many years and may be preferred in applications where cost or space is critical. Note that in both cases the crystal loading capacitors are connected between the oscillator and VDD ; do not use VSS as an AC ground. The Simplified Block Diagram shows that the oscillating inverter does not directly connect to VSS but is referenced to VDD and VRN . Therefore VDD is the best AC ground available. +5V C1 XTAL 2 OSC IN C2 3 OSC OUT + 1 VDD - VREG FIGURE 3. - VREG HA7210 FIGURE 2. Typical values of the capacitors in Figure 2 are shown below. Some trial and error may be required before the best combination is determined. The values listed are total capacitance including parasitic or other sources. Remember that in the 10kHz to 100kHz frequency range setting the HA7210 switches in two internal 15pF capacitors. CRYSTAL FREQUENCY 32kHz 1MHz 2MHz 4MHz LOAD CAPS C1, C2 33pF 33pF 25pF 22pF TRIMMER CAP C3 5pF to 50pF 5pF to 50pF 5pF to 50pF 5pF to 100pF Frequency Fine Tuning Two Methods will be discussed for fine adjustment of the crystal frequency. The first and preferred method (Figure 2), provides better frequency accuracy and oscillator stability than method two (Figure 3). Method one also eliminates start-up problems sometimes encountered with 32kHz tuning fork crystals. For best oscillator performance, two conditions must be met: the capacitive load must be matched to both the inverter and crystal to provide ideal conditions for oscillation, and the frequency of the oscillator must be adjustable to the desired 5 HA7210 Crystal Pullability Figure 4 shows the basic equivalent circuit for a crystal and its loading circuit. VDD LM RM C2 Layout Considerations Due to the extremely low current (and therefore high impedance) the circuit board layout of the HA7210 must be given special attention. Stray capacitance should be minimized. Keep the oscillator traces on a single layer of the PCB. Avoid putting a ground plane above or below this layer. The traces between the crystal, the capacitors, and the OSC pins should be as short as possible. Completely surround the oscillator components with a thick trace of VDD to minimize coupling with any digital signals. The final assembly must be free from contaminants such as solder flux, moisture, or any other potential source of leakage. A good solder mask will help keep the traces free of moisture and contamination over time. CM C1 2 OSC IN C0 3 OSC OUT FIGURE 4. Where: CM = Motional Capacitance LM = Motional Inductance RM = Motional Resistance C0 = Shunt Capacitance 1 C CL = -------------------------- = Equivalent Crystal Load 1 1  ------ + ------  C  1 C2 Further Reading Al Little “HA7210 Low Power Oscillator: Micropower Clock Oscillator and Op Amps Provide System Shutdown for Battery Circuits”. Intersil Corporation Application Note AN9317. Robert Rood “Improving Start-Up Time at 32kHz for the HA7210 Low Power Crystal Oscillator”. Intersil Corporation Application Note AN9334. S. S. Eaton “Timekeeping Advances Through COS/MOS Technology”. Intersil Corporation Application Note ICAN-6086. E. A. Vittoz, et. al. “High-Performance Crystal Oscillator Circuits: Theory and Application”. IEEE Journal of SolidState Circuits, Vol. 23, No. 3, June 1988, pp774-783. M. A. Unkrich, et. al. “Conditions for Start-Up in Crystal Oscillators”. IEEE Journal of Solid-State Circuits, Vol. 17, No. 1, Feb. 1982, pp87-90. Marvin E. Frerking “Crystal Oscillator Design and Temperature Compensation”. New York: Van NostrandReinhold, 1978. Pierce Oscillators Discussed pp56-75. If loading capacitance is connected to a Series Mode Crystal, the new Parallel Mode frequency of resonance may be calculated with the following equation: CM f P = f S 1 + --------------------------------2(C + C ) 0 CL Where: fP = Parallel Mode Resonant Frequency fS = Series Mode Resonant Frequency In a similar way, the Series Mode resonant frequency may be calculated from a Parallel Mode crystal and then you may calculate how much the frequency will “pull” with a new load. 6 HA7210 Typical Performance Curves CL = 40pF, fOSC = 5MHz, VDD = 5V, VSS = GND CL = 18pF, fOSC = 5MHz, VDD = 5V, VSS = GND 1.0V/DIV. 20.0ns/DIV. 1.0V/DIV. 20.0ns/DIV. FIGURE 5. OUTPUT WAVEFORM (CL = 40pF) FIGURE 6. OUTPUT WAVEFORM (CL = 18pF) 1050 fIN = 5MHz, EN = 1, F1 = 0, F2 = 0, CL = 30pF, VDD = 5V 1000 SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 950 900 850 XTAL AT 25oC 800 750 -100 GENERATOR (1VP-P) (NOTE) 26 EN = 1, F1 = 1, F2 = 1, fIN = 100kHz, CL = 30pF, VDD = 5V 25 24 23 22 21 20 19 18 -100 XTAL AT 25oC GENERATOR (1VP-P) (NOTE) -50 0 50 100 150 -50 0 50 100 150 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 7. SUPPLY CURRENT vs TEMPERATURE FIGURE 8. SUPPLY CURRENT vs TEMPERATURE 350 fIN = 5MHz, EN = 0, F1 = 0, F2 = 0, VDD = 5V 300 SUPPLY CURRENT (µA) 250 GENERATOR (1VP-P) (NOTE) 200 150 100 50 0 -100 XTAL AT 25oC SUPPLY CURRENT (µA) 7.5 EN = 0, F1 = 1, F2 = 1, fIN = 100kHz, VDD = 5V 7 6.5 6 GENERATOR (1VP-P) (NOTE) 5.5 5 4.5 4 -100 XTAL AT 25oC -50 0 50 100 150 -50 0 50 100 150 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 9. DISABLE SUPPLY CURRENT vs TEMPERATURE NOTE: Refer to Test Circuit (Figure 1). FIGURE 10. DISABLE SUPPLY CURRENT vs TEMPERATURE 7 HA7210 Typical Performance Curves 3000 EN = 1, F1 = 0, F2 = 0, CL = 18pF, GENERATOR (1VP-P) (NOTE) 2500 SUPPLY CURRENT (µA) VDD = +8V 2000 1500 1000 500 0 4 5 6 7 8 9 10 11 FREQUENCY (MHz) VDD = +5V SUPPLY CURRENT (µA) 1200 VDD = +8V 1000 800 600 VDD = +3V 400 200 0 0 1 2 3 4 5 6 FREQUENCY (MHz) VDD = +5V (Continued) 1400 EN = 1, F1 = 0, F2 =1, CL = 18pF, GENERATOR (1VP-P) (NOTE) FIGURE 11. SUPPLY CURRENT vs FREQUENCY FIGURE 12. SUPPLY CURRENT vs FREQUENCY 300 EN = 1, F1 = 0, F2 = 0, CL = 18pF, GENERATOR (1VP-P) (NOTE) 250 SUPPLY CURRENT (µA) VDD = +8V 200 VDD = +5V 150 100 VDD = +3V 50 0 0 100 200 300 400 500 600 700 800 900 1000 1100 FREQUENCY (kHz) SUPPLY CURRENT (µA) 50 EN = 1, F1 = 0, F2 = 0, CL = 18pF, GENERATOR (1VP-P) (NOTE) 40 VDD = +8V 30 20 VDD = +5V 10 VDD = +3V 0 0 10 20 30 40 50 60 70 80 90 100 110 FREQUENCY (kHz) FIGURE 13. SUPPLY CURRENT vs FREQUENCY FIGURE 14. SUPPLY CURRENT vs FREQUENCY 250 EN = 0, F1 = 0, F2 = 0, CL = 18pF, GENERATOR (1VP-P) (NOTE) 120 VDD = +8V 110 SUPPLY CURRENT (µA) 100 90 80 70 60 50 40 30 4 5 6 7 8 FREQUENCY (MHz) 9 10 11 EN = 0, F1 = 0, F2 = 1, CL = 18pF, GENERATOR (1VP-P) (NOTE) VDD = +8V SUPPLY CURRENT (µA) 200 VDD = +5V 150 VDD = +5V 100 50 VDD = +3V 0 VDD = +3V 0 1 2 3 4 5 6 FREQUENCY (MHz) FIGURE 15. DISABLED SUPPLY CURRENT vs FREQUENCY NOTE: Refer to Test Circuit (Figure 1). FIGURE 16. DISABLE SUPPLY CURRENT vs FREQUENCY 8 HA7210 Typical Performance Curves 35 VDD = +8V SUPPLY CURRENT (µA) 30 SUPPLY CURRENT (µA) VDD = +5V 25 20 15 10 3 5 0 100 200 300 400 500 600 700 800 900 1000 1100 FREQUENCY (kHz) 2 0 10 20 30 40 50 60 70 80 90 100 110 FREQUENCY (kHz) 9 8 7 6 5 4 VDD = +3V VDD = +5V (Continued) EN = 0, F1 = 1, F2 = 1, CL = 18pF, GENERATOR (1VP-P) (NOTE) 11 10 VDD = +8V EN = 0, F1 = 1, F2 = 0, CL = 18pF, GENERATOR (1VP-P) (NOTE) VDD = +3V FIGURE 17. DISABLE SUPPLY CURRENT vs FREQUENCY FIGURE 18. DISABLE SUPPLY CURRENT vs FREQUENCY 3000 EN = 1, F1 = 0, F2 = 0, VDD = +5V, GENERATOR (1VP-P) (NOTE) CL = 40pF EN = 1, F1 = 0, F2 = 1, VDD = +5V, GENERATOR (1VP-P) (NOTE) 1400 CL = 40pF 1200 SUPPLY CURRENT (µA) 1000 800 600 400 200 CL = 18pF SUPPLY CURRENT (µA) 2500 2000 1500 CL = 18pF 1000 500 0 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 FREQUENCY (MHz) FREQUENCY (MHz) FIGURE 19. SUPPLY CURRENT vs FREQUENCY FIGURE 20. SUPPLY CURRENT vs FREQUENCY EN = 1, F1 = 1, F2 = 0, VDD = +5V, GENERATOR (1VP-P) (NOTE) 300 CL = 40pF SUPPLY CURRENT (µA) 250 SUPPLY CURRENT (µA) 200 150 CL = 18pF 100 50 0 0 100 200 300 400 500 600 700 800 900 1000 1100 FREQUENCY (kHz) 30 25 20 15 10 5 0 0 35 EN = 1, F1 = 1, F2 = 1, VDD = +5V, GENERATOR (1VP-P) (NOTE) CL = 40pF CL = 18pF 10 20 30 40 50 60 70 FREQUENCY (kHz) 80 90 100 110 FIGURE 21. SUPPLY CURRENT vs FREQUENCY NOTE: Refer to Test Circuit (Figure 1). FIGURE 22. SUPPLY CURRENT vs FREQUENCY 9 HA7210 Typical Performance Curves 60 55 DUTY CYCLE (%) DUTY CYCLE (%) XTAL AT 25oC 50 45 40 GENERATOR (1VP-P) (NOTE) 35 30 -100 20 10 -100 (Continued) fIN = 100kHz, F1 = 1, F2 = 1, CL = 30pF, VDD = 5V 70 GENERATOR (1VP-P) (NOTE) 60 50 40 30 XTAL AT 25oC fIN = 5MHz, F1 = 0, F2 = 0, CL = 30pF, VDD = 5V -50 0 50 100 150 -50 0 50 100 150 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 23. DUTY CYCLE vs TEMPERATURE FIGURE 24. DUTY CYCLE vs TEMPERATURE F1 = F2 = 0, VDD = 5V, CL = 18pF, C1 = C2 = 0 70 DATA COLLECTED USING CRYSTALS AT EACH FREQUENCY DUTY CYCLE (%) F1 = 0, F2 = 1, VDD = 5V, CL = 18pF, C1 = C2 = 0 70 65 60 55 50 45 DATA COLLECTED USING CRYSTALS AT EACH FREQUENCY 65 DUTY CYCLE (%) 60 55 50 F1 = 0, F2 = 0 RECOMMENDED FOR 5MHz TO 10MHz RANGE 45 0 5 10 FREQUENCY (MHz) 15 20 F1 = 0, F2 = 1 RECOMMENDED FOR 1MHz TO 5MHz RANGE 40 0 1 2 3 4 5 6 FREQUENCY (MHz) 7 8 9 FIGURE 25. DUTY CYCLE vs FREQUENCY FIGURE 26. DUTY CYCLE vs FREQUENCY F1 = 1, F2 = 0, VDD = 5V, CL = 18pF, C1 = C2 = 0 65 DATA COLLECTED USING CRYSTALS AT EACH FREQUENCY DUTY CYCLE (%) 47 46 45 44 43 42 41 F1 = 1, F2 = 0 RECOMMENDED FOR 100kHz TO 1MHz RANGE 40 0 500 1000 1500 2000 2500 3000 3500 FREQUENCY (kHz) 40 0 50 F1 = F2 = 1, VDD = 5V, CL = 18pF, C1 = C2 = 0 DATA COLLECTED USING CRYSTALS AT EACH FREQUENCY 60 DUTY CYCLE (%) 55 50 45 F1 = 1, F2 = 1 RECOMMENDED FOR 10kHz TO 100kHz RANGE 100 FREQUENCY (kHz) 150 200 FIGURE 27. DUTY CYCLE vs FREQUENCY NOTE: Refer to Test Circuit (Figure 1). FIGURE 28. DUTY CYCLE vs FREQUENCY 10 HA7210 Typical Performance Curves 30 25 FREQUENCY CHANGE (PPM) 20 15 10 5 0 -5 -10 -15 -20 2 DEVIATION FROM FREQUENCY AT 5.0V 4 VDD SUPPLY VOLTAGE (V) 6 0 -100 -50 32kHz 1MHz 5MHz 10MHz EDGE JITTER (% OF PERIOD) VDD = 5V, CL = 30pF, GENERATOR (1VP-P) (NOTE) 6 5 4 3 2 1 (Continued) fIN = 5MHz, F1 = 0, F2 = 0 fIN = 100kHz, F1 = 1, F2 = 1 0 50 TEMPERATURE (oC) 100 150 FIGURE 29. FREQUENCY CHANGE vs VDD FIGURE 30. EDGE JITTER vs TEMPERATURE fIN = 5MHz, F1 = 0, F2 = 0, CL = 30pF, VDD = 5V 13 12 11 RISE/FALL TIME (ns) 10 9 8 7 6 5 4 3 2 -100 tr GENERATOR (1VP-P) (NOTE) tr XTAL AT 25oC tf XTAL AT 25oC RISE/FALL TIME (ns) tf GENERATOR (1VP-P) (NOTE) 12 11 10 9 8 7 6 5 4 3 -50 0 50 100 150 2 -100 -50 fIN = 100kHz, F1 = 1, F2 = 1, CL = 30pF, VDD = 5V tf GENERATOR (1VP-P) (NOTE) tr GENERATOR (1VP-P) (NOTE) tf XTAL AT 25oC tr XTAL AT 25oC 0 50 100 150 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 31. RISE/FALL TIME vs TEMPERATURE FIGURE 32. RISE/FALL TIME vs TEMPERATURE VDD = 5V, GENERATOR (1VP-P) (NOTE) 30 tf (fIN = 100kHz) RISE/FALL TIME (ns) 25 tf (fIN = 5MHz) 20 RISE/FALL TIME (ns) tr (fIN = 5MHz) tr (fIN = 100kHz) 15 15 14 13 12 11 10 9 8 7 6 5 10 20 30 40 50 60 CL (pF) 70 80 90 100 110 4 2 3 4 CL = 18pF, GENERATOR (1VP-P) (NOTE) tf (fIN = 5MHz) tf (fIN = 100kHz) tr (fIN = 5MHz) tr (fIN = 100kHz) 10 5 5 6 VDD (+V) 7 8 9 FIGURE 33. RISE/FALL TIME vs CL NOTE: Refer to Test Circuit (Figure 1). FIGURE 34. RISE/FALL TIME vs VDD 11 HA7210 Typical Performance Curves 620 TRANSCONDUCTANCE (µA/V) 580 540 500 460 PHASE (DEGREES) 420 380 340 300 260 10K 2 50Ω 3 100Ω HA7210 1000pF 1µF 178o 180 170 160 150 140 10M 436.5µA/V F1 = 0, F2 = 0 (Continued) VDD = 5V, VSS = GND F1 = 0, F2 = 1 TRANSCONDUCTANCE (µA/V) VDD = 5V, VSS = GND 500 460 420 380 340 311.6µA/V 260 1000pF 2 50Ω 1 µF 3 177o 100Ω 170 160 150 140 130 10M HA7210 100K 1M FREQUENCY (Hz) 10K 100K 1M FREQUENCY (Hz) FIGURE 35. TRANSCONDUCTANCE vs FREQUENCY FIGURE 36. TRANSCONDUCTANCE vs FREQUENCY TRANSCONDUCTANCE (µA/V) 240 220 200 180 160 176.6o 1000pF 2 50Ω 3 1µF F1 = 1, F2 = 0 VDD = 5V, VSS = GND 20 15 TRANSCONDUCTANCE (µA/V) 10 5 0 166o 1 µF 3 156.7µA/V F1 = 1, F2 = 1 6.56µA/V VDD = 5V, VSS = GND 180 PHASE (DEGREES) 170 160 150 140 2 50Ω 100Ω HA7210 130 120 110 1M 120 100 170 160 100Ω 150 140 130 10M PHASE (DEGREES) 140 180 1000pF HA7210 10K 100K 1M FREQUENCY (Hz) 10K 100K FREQUENCY (Hz) FIGURE 37. TRANSCONDUCTANCE vs FREQUENCY FIGURE 38. TRANSCONDUCTANCE vs FREQUENCY F1 = F2 = 1, VDD = 5V, CL = 18pF, TA = 25oC, fOSC = 32.768kHz 60 55 DUTY CYCLE (%) EPSON PART # C-001R32.768K-A 50 XTAL 45 NDK PART # MX-38 2 OSC IN HA7210 35 0 20 40 60 RS ( k Ω ) 80 100 120 RS 3 OSC OUT 40 NOTE: Figure 39 (Duty Cycle vs RS at 32kHz) should only be used for 32kHz crystals. RS may be used at other frequencies to adjust Duty Cycle but experimentation will be required to find an appropriate value. The RS value will be proportional to the effective series resistance of the crystal being used. NOTE: Refer to Test Circuit (Figure 1). FIGURE 39. DUTY CYCLE vs RS at 32kHz 12 PHASE (DEGREES) 300 180 HA7210 Die Characteristics DIE DIMENSIONS: 68 mils x 64 mils x 14 mils METALLIZATION: Type: SiAl Thickness: 10kÅ ±1kÅ SUBSTRATE POTENTIAL: VSS PASSIVATION: Type: Nitride (Si3N4) Over Silox (SiO2, 3% Phos) Silox Thickness: 7kÅ ±1kÅ Nitride Thickness: 8kÅ ±1kÅ Metallization Mask Layout HA7210 (8) ENABLE (1) VDD (7) FREQ 2 CRYSTAL (2) CRYSTAL (3) (6) FREQ 1 VSS (4) 13 OUTPUT (5) HA7210 Dual-In-Line Plastic Packages (PDIP) N E1 INDEX AREA 12 3 N/2 E8.3 (JEDEC MS-001-BA ISSUE D) 8 LEAD DUAL-IN-LINE PLASTIC PACKAGE INCHES SYMBOL -B- MILLIMETERS MIN 0.39 2.93 0.356 1.15 0.204 9.01 0.13 7.62 6.10 MAX 5.33 4.95 0.558 1.77 0.355 10.16 8.25 7.11 NOTES 4 4 8, 10 5 5 6 5 6 7 4 9 Rev. 0 12/93 MIN 0.015 0.115 0.014 0.045 0.008 0.355 0.005 0.300 0.240 MAX 0.210 0.195 0.022 0.070 0.014 0.400 0.325 0.280 -AD BASE PLANE SEATING PLANE D1 B1 B 0.010 (0.25) M D1 A1 A2 L A C L E A A1 A2 B B1 C D D1 E -C- eA eC C e C A BS eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). E1 e eA eB L N 0.100 BSC 0.300 BSC 0.115 8 0.430 0.150 - 2.54 BSC 7.62 BSC 10.92 3.81 8 2.93 14 HA7210 Small Outline Plastic Packages (SOIC) N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM M8.15 (JEDEC MS-012-AA ISSUE C) 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A L MILLIMETERS MIN 1.35 0.10 0.33 0.19 4.80 3.80 MAX 1.75 0.25 0.51 0.25 5.00 4.00 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93 MIN 0.0532 0.0040 0.013 0.0075 0.1890 0.1497 MAX 0.0688 0.0098 0.020 0.0098 0.1968 0.1574 A1 B C D E α µ A1 0.10(0.004) C e H h L N 0.050 BSC 0.2284 0.0099 0.016 8 0o 8o 0.2440 0.0196 0.050 1.27 BSC 5.80 0.25 0.40 8 0o 6.20 0.50 1.27 e B 0.25(0.010) M C AM BS NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. α All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15