HI5735

HI5735 January 1998 12-Bit, 80 MSPS, High Speed Video D/A Converter Description The HI5735 is a 12-bit, 80 MSPS, D/A converter which is implemented in the Intersil BiCMOS 10V (HBC-10) process. Operating from +5V and -5.2V, the converter provides -20.48mA of full scale output current and includes an input data register and bandgap voltage reference. Low glitch energy and excellent frequency domain performance are achieved using a segmented architecture. The digital inputs are TTL/CMOS compatible and translated internally to ECL. All internal logic is implemented in ECL to achieve high switching speed with low noise. The addition of laser trimming assures 12-bit linearity is maintained along the entire transfer curve. Features • Throughput Rate . . . . . . . . . . . . . . . . . . . . . . . 80 MSPS • Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .650mW • Integral Linearity Error . . . . . . . . . . . . . . . . . . 0.75 LSB • Low Glitch Energy . . . . . . . . . . . . . . . . . . . . . . . . 3.0pV-s • TTL/CMOS Compatible Inputs • Improved Hold Time . . . . . . . . . . . . . . . . . . . . . . 0.25ns • Excellent Spurious Free Dynamic Range Applications • Professional Video • Cable TV Headend Equipment Ordering Information PART NUMBER HI5735KCP HI5735KCB TEMP. RANGE (oC) 0 to 70 0 to 70 PACKAGE 28 Lead PDIP 28 Lead SOIC PKG. NO. E28.6 M28.3 Pinout HI5735 (PDIP, SOIC) TOP VIEW D11 (MSB) 1 D10 2 D9 3 D8 4 D7 5 D6 6 D5 7 D4 8 D3 9 D2 10 D1 11 D0 (LSB) 12 NC 13 NC 14 28 DGND 27 AGND 26 REF OUT 25 CTRL OUT 24 CTRL IN 23 RSET 22 AVEE 21 IOUT 20 IOUT 19 ARTN 18 DVEE 17 DGND 16 DVCC 15 CLOCK CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 File Number 4133.3 1621 HI5735 Typical Application Circuit +5V 0.01µF VCC (16) D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D11 (MSB) (1) D10 (2) D9 (3) D8 (4) D7 (5) D6 (6) D5 (7) D4 (8) D3 (9) D2 (10) D1 (11) D0 (LSB) (12) CLK (15) 50Ω DGND (17, 28) (20) IOUT (23) RSET (19) ARTN (27) AGND 976Ω (21) IOUT D/A OUT 64Ω 64Ω -5.2V (AVEE) (26) REF OUT (24) CTRL IN (25) CTRL OUT 0.1µF HI5735 DVEE (18) 0.1µF 0.01µF - 5.2V(DVEE) (22) AVEE 0.01µF - 5.2V(AVEE) 0.1µF Functional Block Diagram (LSB) D0 D1 D2 D3 D4 D5 D6 D7 D8 15 D9 D10 (MSB) D11 REF CELL CLK OVERDRIVEABLE VOLTAGE REFERENCE RSET + 25Ω CTRL IN CTRL OUT UPPER 4-BIT DECODER 15 15 SWITCHED CURRENT CELLS 12-BIT MASTER REGISTER DATA BUFFER/ LEVEL SHIFTER SLAVE REGISTER 227Ω 227Ω 8 LSBs CURRENT CELLS R2R NETWORK ARTN IOUT IOUT - AVEE AGND DVEE DGND VCC REF OUT 1622 HI5735 Absolute Maximum Ratings Digital Supply Voltage VCC to DGND . . . . . . . . . . . . . . . . . . . +5.5V Negative Digital Supply Voltage DVEE to DGND . . . . . . . . . . . -5.5V Negative Analog Supply Voltage AVEE to AGND, ARTN . . . . . -5.5V Digital Input Voltages (D11-D0, CLK) to DGND . . . . . DVCC to -0.5V Internal Reference Output Current . . . . . . . . . . . . . . . . . . . . ±2.5mA Voltage from CTRL IN to AVEE. . . . . . . . . . . . . . . . . . . . . 2.5V to 0V Control Amplifier Output Current . . . . . . . . . . . . . . . . . . . . . ±2.5mA Reference Input Voltage Range . . . . . . . . . . . . . . . . . -3.7V to AVEE Analog Output Current (IOUT) . . . . . . . . . . . . . . . . . . . . . . . . . 30mA Thermal Information Thermal Resistance (Typical, Note 1) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Maximum Junction Temperature Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range HI5735BIx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications AVEE , DVEE = -4.94 to -5.46V, VCC = +4.75 to +5.25V, VREF = Internal TA = 25oC for All Typical Values HI5735BI TA = 0oC TO 70oC PARAMETER SYSTEM PERFORMANCE Resolution Integral Linearity Error, INL Differential Linearity Error, DNL Offset Error, IOS Full Scale Gain Error, FSE Offset Drift Coefficient Full Scale Output Current, IFS Output Voltage Compliance Range DYNAMIC CHARACTERISTICS Throughput Rate Output Voltage Full Scale Step Settling Time, tSETT Full Scale Single Glitch Area, GE (Peak) Doublet Glitch Area, (Net) Output Slew Rate Output Rise Time Output Fall Time Differential Gain Differential Phase (Note 5) (Note 3) TEST CONDITIONS MIN TYP MAX UNITS 12 (Note 4) (“Best Fit” Straight Line) (Note 4) (Note 4) (Notes 2, 4) (Note 3) -1.25 0.75 0.5 20 1 20.48 - 1.5 1.0 75 10 0.05 0 Bits LSB LSB µA % µA/oC mA V 80 - 20 5 3 1,000 675 470 0.15 0.07 - MSPS ns pV-s pV-s V/µs ps ps % Deg To ±0.5 LSB Error Band RL = 50Ω (Note 3) RL = 50Ω (Note 3) RL = 50Ω, DAC Operating in Latched Mode (Note 3) RL = 50Ω, DAC Operating in Latched Mode (Note 3) RL = 50Ω, DAC Operating in Latched Mode (Note 3) RL = 50Ω (Note 3) RL = 50Ω (Note 3) - 1623 HI5735 Electrical Specifications AVEE , DVEE = -4.94 to -5.46V, VCC = +4.75 to +5.25V, VREF = Internal TA = 25oC for All Typical Values (Continued) HI5735BI TA = 0oC TO 70oC PARAMETER Spurious Free Dynamic Range to Nyquist (Note 3) REFERENCE/CONTROL AMPLIFIER Internal Reference Voltage, VREF Internal Reference Voltage Drift Internal Reference Output Current Sink/Source Capability Internal Reference Load Regulation Input Impedance at REF OUT pin Amplifier Large Signal Bandwidth (0.6VP-P) Amplifier Small Signal Bandwidth (0.1VP-P) Reference Input Impedance Reference Input Multiplying Bandwidth (CTL IN) DIGITAL INPUTS (D9-D0, CLK, INVERT) Input Logic High Voltage, VIH Input Logic Low Voltage, VIL Input Logic Current, IIH Input Logic Current, IIL Digital Input Capacitance, CIN TIMING CHARACTERISTICS Data Setup Time, tSU Data Hold Time, tHLD Propagation Delay Time, tPD CLK Pulse Width, tPW1, tPW2 POWER SUPPLY CHARACTERISITICS IEEA IEED ICCD Power Dissipation Power Supply Rejection Ratio NOTES: 2. Gain Error measured as the error in the ratio between the full scale output current and the current through RSET (typically 1.28mA). Ideally the ratio should be 16. 3. Parameter guaranteed by design or characterization and not production tested. 4. All devices are 100% tested at 25oC. 100% production tested at temperature extremes for military temperature devices, sample tested for industrial temperature devices. 5. Dynamic Range must be limited to a 1V swing within the compliance range. (Note 4) (Note 4) (Note 4) (Note 4) VCC ±5%, VEE ±5% 42 70 13 650 5 50 85 20 mA mA mA mW µA/V See Figure 1 (Note 3) See Figure 1 (Note 3) See Figure 1 (Note 3) See Figure 1 (Note 3) 3.0 0.5 3.0 2.0 0.25 4.5 ns ns ns ns (Note 4) (Note 4) (Note 4) (Note 4) (Note 3) 2.0 3.0 0.8 400 700 V V µA µA pF (Note 4) (Note 3) (Note 3) IREF = 0 to IREF = -125µA (Note 3) Sine Wave Input, to Slew Rate Limited (Note 3) Sine Wave Input, to -3dB Loss (Note 3) (Note 3) RL = 50Ω , 100mV Sine Wave, to -3dB Loss at IOUT (Note 3) -1.27 -125 -1.23 50 50 1.4 3 10 12 200 -1.17 +50 V µV/oC µA µV kΩ MHz MHz kΩ MHz TEST CONDITIONS fCLK = 40MHz, fOUT = 2.02MHz, 20MHz Span fCLK = 80MHz, fOUT = 2.02MHz, 40MHz Span MIN TYP 70 70 MAX UNITS dBc dBc 1624 HI5735 Timing Diagrams 50% CLK V D11-D0 GLITCH AREA = 1/2 (H x W) HEIGHT (H) ±1/2 LSB ERROR BAND IOUT WIDTH (W) t(ps) tPD tSETT FIGURE 1. FULL SCALE SETTLING TIME DIAGRAM FIGURE 2. PEAK GLITCH AREA (SINGLET) MEASUREMENT METHOD tPW1 tPW2 CLK 50% tSU tHLD D11-D0 tSU tHLD tSU tHLD tPD IOUT tPD tPD FIGURE 3. PROPAGATION DELAY, SETUP TIME, HOLD TIME AND MINIMUM PULSE WIDTH DIAGRAM 1625 HI5735 Typical Performance Curves 680 CLOCK FREQUENCY DOES NOT ALTER POWER DISSIPATION 640 (mW) (V) 600 560 -50 -30 -10 10 30 50 70 90 -1.21 -1.23 -1.25 -1.27 -1.29 -50 -30 -10 10 30 50 70 90 TEMPERATURE TEMPERATURE FIGURE 4. TYPICAL POWER DISSIPATION OVER TEMPERATURE FIGURE 5. TYPICAL REFERENCE VOLTAGE OVER TEMPERATURE 1.5 0.8 0.5 (LSB) 0.4 (LSB) 1.5 0 600 1200 1800 2400 3000 3600 4200 0.0 -0.5 -0.4 -0.8 400 1000 1600 2200 CODE 2800 3400 4000 CODE FIGURE 6. TYPICAL INL FIGURE 7. TYPICAL DNL 28 ATTEN 20dB RL -10.0dBm 10dB/ ∆MKR -87.33dB -73kHz fC = 10 MSPS 24 (µA) 20 S 16 12 C -40 -20 -0 20 40 60 80 100 CENTER 1.237MHz SPAN 2.000MHz TEMPERATURE FIGURE 8. OFFSET CURRENT OVER TEMPERATURE FIGURE 9. SPURIOUS FREE DYNAMIC RANGE = 87.3dBc 1626 HI5735 Pin Descriptions PIN NUMBER 1-12 15 13, 14 16 17, 28 18 23 27 19 21 20 22 24 25 26 PIN NAME D11 (MSB) thru D0 (LSB) CLK NC VCC DGND DVEE RSET AGND ARTN IOUT IOUT AVEE CTRL IN CTRL OUT REF OUT PIN DESCRIPTION Digital Data Bit 11, the Most Significant Bit thru Digital Data Bit 0, the Least Significant Bit. Data Clock Pin DC to 80 MSPS. No Connect. Digital Logic Supply +5V. Digital Ground. -5.2V Logic Supply. External resistor to set the full scale output current. IFS = 16 x (VREF OUT / RSET). Typically 976Ω . Analog Ground supply current return pin. Analog Signal Return for the R/2R ladder. Current Output Pin. Complementary Current Output Pin. -5.2V Analog Supply. Input to the current source base rail. Typically connected to CTRL OUT and a 0.1µF capacitor to AVEE . Allows external control of the current sources. Control Amplifier Out. Provides precision control of the current sources when connected to CTRL IN such that IFS = 16 x (VREF OUT / RSET). -1.23V (typical) bandgap reference voltage output. Can sink up to 125µA or be overdriven by an external reference capable of delivering up to 2mA. Detailed Description The HI5735 is a 12-bit, current out D/A converter. The DAC can convert at 80 MSPS and runs on +5V and -5.2V supplies. The architecture is an R/2R and segmented switching current cell arrangement to reduce glitch. Laser trimming is employed to tune linearity to true 12-bit levels. The HI5735 achieves its low power and high speed performance from an advanced BiCMOS process. The HI5735 consumes 650mW (typical) and has an improved hold time of only 0.25ns (typical). Digital Inputs The HI5735 is a TTL/CMOS compatible D/A. Data is latched by a Master register. Once latched, data inputs D0 (LSB) thru D11 (MSB) are internally translated from TTL to ECL. The internal latch and switching current source controls are implemented in ECL technology to maintain high switching speeds and low noise characteristics. Decoder/Driver The architecture employs a split R/2R ladder and Segmented Current source arrangement. Bits D0 (LSB) thru D7 directly drive a typical R/2R network to create the binary weighted current sources. Bits D8 thru D11 (MSB) pass thru a “thermometer” decoder that converts the incoming data into 15 individual segmented current source enables. This split architecture helps to improve glitch, thus resulting in a more constant glitch characteristic across the entire output transfer function. Clocks and Termination The internal 12-bit register is updated on the rising edge of the clock. Since the HI5735 clock rate can run to 80 MSPS, HI5735 DAC ZO = 50Ω CLK RT = 50Ω to minimize reflections and clock noise into the part, proper termination should be used. In PCB layout clock runs should be kept short and have a minimum of loads. To guarantee consistent results from board to board, controlled impedance PCBs should be used with a characteristic line impedance ZO of 50Ω . To terminate the clock line, a shunt terminator to ground is the most effective type at a 80 MSPS clock rate. A typical value for termination can be determined by the equation: RT = ZO , for the termination resistor. For a controlled impedance board with a ZO of 50Ω , the RT = 50Ω . Shunt termination is best used at the receiving end of the transmission line or as close to the HI5735 CLK pin as possible. FIGURE 10. CLOCK LINE TERMINATION Rise and Fall times and propagation delay of the line will be affected by the Shunt Terminator. The terminator should be connected to DGND. 1627 HI5735 Noise Reduction To reduce power supply noise, separate analog and digital power supplies should be used with 0.1µF and 0.01µF ceramic capacitors placed as close to the body of the HI5735 as possible on the analog (AVEE) and digital (DVEE) supplies. The analog and digital ground returns should be connected together back at the device to ensure proper operation on power up. The VCC power pin should also be decoupled with a 0.1µF capacitor. Reference The internal reference of the HI5735 is a -1.23V (typical) bandgap voltage reference with 50µV/oC of temperature drift (typical). The internal reference is connected to the Control Amplifier which in turn drives the segmented current cells. Reference Out (REF OUT) is internally connected to the Control Amplifier. The Control Amplifier Output (CTRL OUT) should be used to drive the Control Amplifier Input (CTRL IN) and a 0.1µF capacitor to analog VEE . This improves settling time by providing an AC ground at the current source base node. The Full Scale Output Current is controlled by the REF OUT pin and the set resistor (RSET). The ratio is: IOUT (Full Scale) = (VREF OUT /RSET) x 16. The internal reference (REF OUT) can be overdriven with a more precise external reference to provide better performance over temperature. Figure 11 illustrates a typical external reference configuration. TABLE 2. INPUT CODING vs CURRENT OUTPUT INPUT CODE (D11-D0) 1111 1111 1111 1000 0000 0000 0000 0000 0000 IOUT (mA) -20.48 -10.24 0 IOUT (mA) 0 -10.24 -20.48 Settling Time The settling time of the HI5735 is measured as the time it takes for the output of the DAC to settle to within a 1/2 LSB error band of its final value during a full scale (code 0000... to 1111.... or 1111... to 0000...) transition. All claims made by Intersil with respect to the settling time performance of the HI5735 have been fully verified by the National Institute of Standards and Technology (NIST) and are fully traceable. Glitch The output glitch of the HI5735 is measured by summing the area under the switching transients after an update of the DAC. Glitch is caused by the time skew between bits of the incoming digital data. Typically, the switching time of digital inputs are asymmetrical, meaning that the turn off time is faster than the turn on time (TTL designs). Unequal delay paths through the device can also cause one current source to change before another. In order to minimize this, the Intersil HI5735 employes an internal register, just prior to the current sources, which is updated on the clock edge. Lastly, the worst case glitch on traditional D/A converters usually occurs at the major transition (i.e., code 2047 to 2048). However, due to the split architecture of the HI5735, the glitch is moved to the 255 to 256 transition (and every subsequent 256 code transitions thereafter). This split R/2R segmented current source architecture, which decreases the amount of current switching at any one time, makes the glitch practically constant over the entire output range. By making the glitch a constant size over the entire output range, this effectively integrates this error out of the end application. In measuring the output glitch of the HI5735 the output is terminated into a 64Ω load. The glitch is measured at any one of the current cell carry (code 255 to 256 transition or any multiple thereof) throughout the DACs output range. The glitch energy is calculated by measuring the area under the voltage-time curve. Figure 13 shows the area considered as glitch when changing the DAC output. Units are typically specified in picoVolt-seconds (pV-s). HI5735 (26) REF OUT -1.25V R -5.2V FIGURE 11. EXTERNAL REFERENCE CONFIGURATION Outputs The outputs IOUT and IOUT are complementary current outputs. Current is steered to either IOUT or IOUT in proportion to the digital input code. The sum of the two currents is always equal to the full scale current minus one LSB. The current output can be converted to a voltage by using a load resistor. Both current outputs should have the same load resistor (64Ω typically). By using a 64Ω load on the output, a 50Ω effective output resistance (ROUT) is achieved due to the 227Ω (±15%) parallel resistance seen looking back into the output. This is the nominal value of the R2R ladder of the DAC. The 50Ω output is needed for matching the output with a 50Ω line. The load resistor should be chosen so that the effective output resistance (ROUT) matches the line resistance. The output voltage is: VOUT = IOUT x ROUT . IOUT is defined in the reference section. IOUT is not trimmed to 12 bits, so it is not recommended that it be used in conjunction with IOUT in a differential-to-single-ended application. The compliance range of the output is from -1.25V to 0V, with a 1VP-P voltage swing allowed within this range. HI5735 (21) IOUT 64Ω 100MHz LOW PASS FILTER SCOPE 50Ω FIGURE 12. GLITCH TEST CIRCUIT 1628 HI5735 Applications Bipolar Applications Definition of Specifications Integral Linearity Error, INL, is the measure of the worst case point that deviates from a best fit straight line of data values along the transfer curve. Differential Linearity Error, DNL, is the measure of the error in step size between adjacent codes along the converter’s transfer curve. Ideally, the step size is 1 LSB from one code to the next, and the deviation from 1 LSB is known as DNL. A DNL specification of greater than -1 LSB guarantees monotonicity. GLITCH ENERGY = (a x t)/2 a (mV) Feedthru, is the measure of the undesirable switching noise coupled to the output. Output Voltage Full Scale Settling Time, is the time required from the 50% point on the clock input for a full scale step to settle within an ±1/2 LSB error band. Output Voltage Small Scale Settling Time, is the time required from the 50% point on the clock input for a 100mV step to settle within an 1/2 LSB error band. This is used by applications reconstructing highly correlated signals such as sine waves with more than 5 points per cycle. Glitch Area, GE, is the switching transient appearing on the output during a code transition. It is measured as the area under the curve and expressed as a picoVolt•Time specification (typically pV•s). Differential Gain, ∆AV , is the gain error from an ideal sine wave with a normalized amplitude. Differential Phase, ∆Φ , is the phase error from an ideal sine wave. t (ns) FIGURE 13. MEASURING GLITCH ENERGY To convert the output of the HI5735 to a bipolar 4V swing, the following applications circuit is recommended. The reference can only provide 125µA of drive, so it must be buffered to create the bipolar offset current needed to generate the -2V output with all bits “off”. The output current must be converted to a voltage and then gained up and offset to produce the proper swing. Care must be taken to compensate for the voltage swing and error 5kΩ REF OUT (26) + 1/2 CA2904 - 5kΩ + 1/2 CA2904 0.1µF 60Ω - HI5735 50Ω IOUT (21) 240Ω 240Ω Signal to Noise Ratio, SNR, is the ratio of a fundamental to the noise floor of the analog output. The first 5 harmonics are ignored, and an output filter of 1/2 the clock frequency is used to eliminate alias products. Total Harmonic Distortion, THD, is the ratio of the DAC output fundamental to the RMS sum of the harmonics. The first 5 harmonics are included, and an output filter of 1/2 the clock frequency is used to eliminate alias products. Spurious Free Dynamic Range, SFDR, is the amplitude difference from a fundamental to the largest harmonically or non-harmonically related spur. A sine wave is loaded into the D/A and the output filtered at 1/2 the clock frequency to eliminate noise from clocking alias terms. Intermodulation Distortion, IMD, is the measure of the sum and difference products produced when a two tone input is driven into the D/A. The distortion products created will arise at sum and difference frequencies of the two tones. IMD can be calculated using the following equation: 20Log (RMS of Sum and Difference Distortion Products) IMD = ------------------------------------------------------------------------------------------------------------------------------------------------------ . ( RMS Amplitude of the Fundamental ) + HFA1100 - VOUT FIGURE 14. BIPOLAR OUTPUT CONFIGURATION 1629 HI5735 Die Characteristics DIE DIMENSIONS: 161.5 mils x 160.7 mils x 19 mils ±1 mil METALLIZATION: Type: AlSiCu Thickness: M1 - 8kÅ, M2 - 17kÅ PASSIVATION: Type: Sandwich Passivation Undoped Silicon Glass (USG) + Nitride Thickness: USG - 8kÅ, Nitride - 4.2kÅ Total 12.2kÅ ± +2kÅ DIE ATTACH: Silver Filled Epoxy SUBSTRATE POTENTIAL (Powered Up): VEED Metallization Mask Layout HI5735 REF OUT AGND D8 D9 D10 D11 DGND CTRL OUT D7 CTRL IN D6 D5 RSET AVEE D4 IOUT D3 IOUT D2 ARTN D1 D0 CLK DVCC DGND DVEE 1630 HI5735 Dual-In-Line Plastic Packages (PDIP) N E1 INDEX AREA 12 3 N/2 -B-AD BASE PLANE SEATING PLANE D1 B1 B 0.010 (0.25) M D1 A1 A2 L A C L E E28.6 (JEDEC MS-001-BF ISSUE D) 28 LEAD NARROW BODY DUAL-IN-LINE PLASTIC PACKAGE INCHES SYMBOL A A1 -C- MILLIMETERS MIN 0.39 3.18 0.356 0.77 0.204 35.1 0.13 15.24 12.32 MAX 6.35 4.95 0.558 1.77 0.381 39.7 15.87 14.73 NOTES 4 4 8 5 5 6 5 6 7 4 9 Rev. 0 12/93 MIN 0.015 0.125 0.014 0.030 0.008 1.380 0.005 0.600 0.485 MAX 0.250 0.195 0.022 0.070 0.015 1.565 0.625 0.580 A2 B B1 C D D1 E E1 e eA eB L N eA eC C e C A BS eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 0.100 BSC 0.600 BSC 0.115 28 0.700 0.200 2.54 BSC 15.24 BSC 2.93 28 17.78 5.08 1631 HI5735 Small Outline Plastic Packages (SOIC) N INDEX AREA E -B1 2 3 SEATING PLANE -AD -CA h x 45o H 0.25(0.010) M BM M28.3 (JEDEC MS-013-AE ISSUE C) 28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A A1 L MILLIMETERS MIN 2.35 0.10 0.33 0.23 17.70 7.40 MAX 2.65 0.30 0.51 0.32 18.10 7.60 NOTES 9 3 4 5 6 7 8o Rev. 0 12/93 MIN 0.0926 0.0040 0.013 0.0091 0.6969 0.2914 MAX 0.1043 0.0118 0.0200 0.0125 0.7125 0.2992 B C D E α A1 0.10(0.004) C e H h L N 0.05 BSC 0.394 0.01 0.016 28 0o 8o 0.419 0.029 0.050 1.27 BSC 10.00 0.25 0.40 28 0o 10.65 0.75 1.27 e B 0.25(0.010) M C AM BS NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. α All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 1632