HIN208CA

HIN201 thru HIN213 TM Data Sheet May 2000 File Number 3980.8 +5V Powered RS-232 Transmitters/Receivers with 0.1Microfarad External Capacitors The HIN201-HIN213 family of RS-232 transmitters/receivers interface circuits meet all ElA RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available. They require a single +5V power supply (except HIN201) and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply. The HIN203 and HIN205 require no external capacitors and are ideally suited for applications where circuit board space is critical. The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The HIN205, HIN206, HIN211 and HIN213 feature a low power shutdown mode to conserve energy in battery powered applications. In addition, the HIN213 provides two active receivers in shutdown mode allowing for easy “wakeup” capability. The drivers feature true TTL/CMOS input compatibility, slew rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V input, and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection. Features • Meets All RS-232E and V.28 Specifications • HIN203 and HIN205 Require No External Capacitors • Requires Only 0.1µF or Greater External Capacitors • High Data Rate. . . . . . . . . . . . . . . . . . . . . . . . . . .120kbit/s • Two Receivers Active in Shutdown Mode (HIN213) • Requires Only Single +5V Power Supply - (+5V and +12V - HIN201) • Onboard Voltage Doubler/Inverter • Low Power Consumption (Typ) . . . . . . . . . . . . . . . . . 5mA • Low Power Shutdown Function (Typ) . . . . . . . . . . . . 1µA • Three-State TTL/CMOS Receiver Outputs • Multiple Drivers - ±10V Output Swing for +5V lnput - 300Ω Power-Off Source Impedance - Output Current Limiting - TTL/CMOS Compatible - 30V/µs Maximum Slew Rate • Multiple Receivers - ±30V Input Voltage Range - 3kΩ to 7kΩ Input Impedance - 0.5V Hysteresis to Improve Noise Rejection Applications • Any System Requiring RS-232 Communications Port - Computer - Portable, Mainframe, Laptop - Peripheral - Printers and Terminals - Instrumentation - Modems Selection Table PART NUMBER HIN201 HIN202 HIN203 HIN205 HIN206 HIN207 HIN208 HIN211 HIN213 POWER SUPPLY VOLTAGE +5V and +9V to 13.2V +5V +5V +5V +5V +5V 5V +5V +5V NUMBER OF RS-232 DRIVERS 2 2 2 5 4 5 4 4 4 NUMBER OF RS-232 RECEIVERS 2 2 2 5 3 3 4 5 5 NUMBER OF 0.1µF EXTERNAL CAPACITORS 2 Capacitors 4 Capacitors None None 4 Capacitors 4 Capacitors 4 Capacitors 4 Capacitors 4 Capacitors LOW POWER SHUTDOWN/TTL THREE-STATE No/No No/No No/No Yes/Yes Yes/Yes No/No No/No Yes/Yes Yes/Yes NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN 0 0 0 0 0 0 0 0 2 3-1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000 HIN201 thru HIN213 Ordering Information PART NO. HIN201CB HIN201IB HIN202CP HIN202CB HIN202IP HIN202CA HIN202IA HIN202IB HIN202CBN HIN202IBN HIN203CP HIN203CB HIN205CP HIN206CP HIN206CB HIN206CA HIN206IP HIN206IB HIN206IA HIN207CP TEMP. RANGE (oC) 0 to 70 -40 to 85 0 to 70 0 to 70 -40 to 85 0 to 70 -40 to 85 -40 to 85 0 to 70 -40 to 85 0 to 70 0 to 70 0 to 70 0 to 70 0 to 70 0 to 70 -40 to 85 -40 to 85 -40 to 85 0 to 70 PACKAGE 16 Ld SOIC (W) 16 Ld SOIC (W) 16 Ld PDIP 16 Ld SOIC (W) 16 Ld PDIP 16 Ld SSOP 16 Ld SSOP 16 Ld SOIC (W) 16 Ld SOIC (N) 16 Ld SOIC (N) 20 Ld PDIP 20 Ld SOIC (W) 24 Ld PDIP (W) 24 Ld PDIP (N) 24 Ld SOIC 24 Ld SSOP 24 Ld PDIP (N) 24 Ld SOIC 24 Ld SSOP 24 Ld PDIP (N) PKG. NO. M16.3 M16.3 E16.3 M16.3 E16.3 M16.209 M16.209 M16.3 M16.15 M16.15 E20.3 M20.3 E24.6 E24.3 M24.3 M24.209 E24.3 M24.3 M24.209 E24.3 PART NO. HIN207CB HIN207CA HIN207IP HIN207IB HIN207IA HIN208CP HIN208CB HIN208CA HIN208IP HIN208IB HIN208IA HIN211CB HIN211CA HIN211IB HIN211IA HIN213CB HIN213CA HIN213IB HIN213IA TEMP. RANGE (oC) 0 to 70 0 to 70 -40 to 85 -40 to 85 -40 to 85 0 to 70 0 to 70 0 to 70 -40 to 85 -40 to 85 -40 to 85 0 to 70 0 to 70 -40 to 85 -40 to 85 0 to 70 0 to 70 -40 to 85 -40 to 85 PACKAGE 24 Ld SOIC 24 Ld SSOP 24 Ld PDIP (N) 24 Ld SOIC 24 Ld SSOP 24 Ld PDIP (N) 24 Ld SOIC 24 Ld SSOP 24 Ld PDIP (N) 24 Ld SOIC 24 Ld SSOP 28 Ld SOIC 28 Ld SSOP 28 Ld SOIC 28 Ld SSOP 28 Ld SOIC 28 Ld SSOP 28 Ld SOIC 28 Ld SSOP PKG. NO. M24.3 M24.209 E24.3 M24.3 M24.209 E24.3 M24.3 M24.209 E24.3 M24.3 M24.209 M28.3 M28.209 M28.3 M28.209 M28.3 M28.209 M28.3 M28.209 NOTE: Most surface mount devices are available on tape and reel; add “-T” to suffix. Pin Descriptions PIN VCC V+ VGND C1+ C1C2+ C2TIN TOUT RIN ROUT EN, EN SD, SD NC FUNCTION Power Supply Input 5V ±10%, 5V ±5% (HIN207, HIN203, and HIN205). Internally generated positive supply (+10V nominal), HIN201 requires +9V to +13.2V. Internally generated negative supply (-10V nominal). Ground Lead. Connect to 0V. External capacitor (+ terminal) is connected to this lead. External capacitor (- terminal) is connected to this lead. External capacitor (+ terminal) is connected to this lead. External capacitor (- terminal) is connected to this lead. Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400kΩ pull-up resistor to VCC is connected to each lead. Transmitter Outputs. These are RS-232 levels (nominally ±10V). Receiver Inputs. These inputs accept RS-232 input levels. An internal 5kΩ pull-down resistor to GND is connected to each input. Receiver Outputs. These are TTL/CMOS levels. Enable Input. This is an active low input which enables the receiver outputs. With EN = 5V, (HIN213 EN = 0V), the outputs are placed in a high impedance state. Shutdown Input. With SD = 5V (HIN213 SD = 0V), the charge pump is disabled, the receiver outputs are in a high impedance state (except R4 and R5 of HIN213) and the transmitters are shut off. No Connect. No connections are made to these leads. 3-2 HIN201 thru HIN213 Pinouts HIN201 (SOIC) TOP VIEW HIN202 (PDIP, SOIC, SSOP) TOP VIEW C+ CVT2OUT R2IN R2OUT T2IN NC 1 2 3 4 5 6 7 8 16 V+ 15 VCC 14 GND 13 T1OUT 12 R1IN 11 R1OUT 10 T1IN 9 NC C1+ 1 V+ 2 C1- 3 C2+ 4 C2- 5 V6 16 VCC 15 GND 14 T1OUT 13 R1IN 12 R1OUT 11 T1IN 10 T2IN 9 R2OUT T2OUT 7 R2IN 8 +5V +9V TO +13.2V +5V 15 VCC 1 0.1µF + 2 V+ 16 1 C+ C+12V TO -12V VOLTAGE INVERTER V- 3 + T1 13 0.1µF 4 0.1µF T1OUT + 5 0.1µF + 3 16 VCC C1+ C1C2+ C2+5V TO 10V VOLTAGE INVERTER V+ 2 + 0.1µF T1IN 10 +5V 400kΩ +5V 400kΩ +10V TO -10V VOLTAGE INVERTER V- 6 + 0.1µF T2 4 12 R1IN R1 5kΩ T2IN 10 12 T2OUT T1IN 11 T2IN 7 11 +5V 400kΩ +5V 400kΩ T1 14 T1OUT R1OUT T2 7 13 R1IN R1 5kΩ T2OUT R2OUT 6 R2 GND 14 5kΩ 5 R1OUT R2IN R2OUT 9 R2 GND 15 5kΩ 8 R2IN 3-3 HIN201 thru HIN213 Pinouts (Continued) HIN203 (PDIP, SOIC) TOP VIEW HIN205 (PDIP) TOP VIEW T2IN T1IN R1OUT R1IN T1OUT GND VCC (V+) C1+ GND 1 2 3 4 5 6 7 8 9 20 R2OUT 19 R2IN 18 T2OUT 17 V16 C215 C2+ 14 V+ (C1-) 13 C1- (C1+) 12 V- (C2+) 11 C2+ (C2-) T4OUT 1 T3OUT 2 T1OUT 3 T2OUT 4 R2IN 5 R2OUT 6 T2IN 7 T1IN 8 R1OUT 9 R1IN 10 GND 11 24 R3IN 23 R3OUT 22 T5IN 21 SD 20 EN 19 T5OUT 18 R4IN 17 R4OUT 16 T4IN 15 T3IN 14 R5OUT 13 R5IN (V-) C2- 10 NOTE: Pin numbers in parentheses are for SOIC Package. VCC 12 +5V + 6 +5V T1IN 2 +5V 1 T2IN 3 R1OUT 5kΩ R2OUT 20 C1+ C1VVV+ GND 6 GND 9 17 R4OUT 5kΩ C2+ C2+ C2C210 (11) R3OUT 19 R2IN 11 (12) 15 16 R2OUT 6 400kΩ 400kΩ VCC T1 5 T1OUT T2IN T2 18 T2OUT 4 R1IN T3IN T4IN T5IN R1OUT 15 16 7 +5V 12 0.1µF +5V T1IN 8 400kΩ VCC T1 3 + 0.1µF T1OUT +5V 400kΩ +5V 400kΩ +5V 400kΩ +5V 400kΩ T2 4 T3 T4 1 T5 19 10 R1 5kΩ 5 R2 5kΩ 24 R3 5kΩ 18 R4 5kΩ 13 R5 GND 11 5kΩ R5IN 21 SD R3IN T5OUT R1IN T4OUT T2OUT T3OUT 2 22 9 8 (13) NO 13 (14) CONNECT INTERNAL -10V SUPPLY INTERNAL +10V SUPPLY 12 (10) 17 14 (8) R2IN 23 R4IN 14 R5OUT 20 EN 3-4 HIN201 thru HIN213 Pinouts (Continued) HIN206 (PDIP, SOIC, SSOP) TOP VIEW 1 2 3 4 5 6 7 8 9 24 T4OUT 23 R2IN 22 R2OUT 21 SD 20 EN 19 T4IN 18 T3IN 17 R3OUT 16 R3IN 15 V14 C213 C2+ HIN207 (PDIP, SOIC, SSOP) TOP VIEW T3OUT T1OUT T2OUT R1IN R1OUT T2IN T1IN GND VCC 1 2 3 4 5 6 7 8 9 24 T4OUT 23 R2IN 22 R2OUT 21 T5IN 20 T5OUT 19 T4IN 18 T3IN 17 R3OUT 16 R3IN 15 V14 C213 C2+ T3OUT T1OUT T2OUT R1IN R1OUT T2IN T1IN GND VCC C1+ 10 V+ 11 C1- 12 C1+ 10 V+ 11 C1- 12 +5V +5V 9 0.1µF 10 C1+ + 12 C113 C2+ + 14 C27 VCC +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER T1 V+ 11 + 0.1µF 0.1µF 10 C1+ + 12 C113 C2+ + 14 C29 VCC +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER T1 V+ 11 + 0.1µF 0.1µF V- 15 + 2 0.1µF T1IN T1OUT T2IN T2OUT T3IN T3OUT T4IN T4OUT R1IN R1 5kΩ 23 R2IN R2 5kΩ 16 R3IN R3 5kΩ 21 SD GND 8 T5IN R1OUT V- 15 + 2 0.1µF T1OUT 0.1µF T1IN +5V 400kΩ +5V 400kΩ 7 +5V 400kΩ +5V 400kΩ T2 3 T3 T2OUT T2IN +5V 400kΩ 6 +5V 400kΩ 18 +5V 400kΩ 19 5 T2 3 T3 6 18 1 T3IN T4IN R1OUT 1 T3OUT T4OUT T5OUT R1IN T4 24 4 +5V 400kΩ 19 +5V 400kΩ T4 24 T5 20 4 R1 5kΩ 23 R2IN R2 5kΩ 16 R3IN R3 GND 8 5kΩ 21 5 22 R2OUT 22 R2OUT 17 R3OUT 20 EN 17 R3OUT 3-5 HIN201 thru HIN213 Pinouts (Continued) HIN208 (PDIP, SOIC, SSOP) TOP VIEW HIN211 (SOIC, SSOP) TOP VIEW T3OUT 1 T2OUT T1OUT R2IN R2OUT T1IN R1OUT R1IN GND VCC 1 2 3 4 5 6 7 8 9 24 T3OUT 23 R3IN 22 R3OUT 21 T4IN 20 T4OUT 19 T3IN 18 T2IN 17 R4OUT 16 R4IN 15 V14 C213 C2+ T1OUT 2 T2OUT 3 R2IN 4 R2OUT 5 T2IN 6 T1IN 7 R1OUT 8 R1IN 9 GND 10 VCC 11 C1+ 12 V+ 13 C1- 14 +5V 11 +5V 9 0.1µF 10 C1+ + 12 C113 C2+ + 14 C2VCC +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER T1 V+ 11 + 0.1µF 0.1µF 12 C1+ + 14 C115 C2+ + 16 C2VCC +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER T1 V+ 13 + 0.1µF 28 T4OUT 27 R3IN 26 R3OUT 25 SD 24 EN 23 R4IN 22 R4OUT 21 T4IN 20 T3IN 19 R5OUT 18 R5IN 17 V16 C215 C2+ C1+ 10 V+ 11 C1- 12 0.1µF V- 15 + 2 0.1µF T1OUT T2IN 1 T2OUT T3IN 24 T3OUT T4IN T4OUT R1OUT R1IN T1IN V- 17 + 2 0.1µF T1OUT 0.1µF +5V 400kΩ 7 +5V 400kΩ +5V 400kΩ +5V 400kΩ T1IN +5V 400kΩ 5 +5V 400kΩ 18 +5V 400kΩ 19 +5V 400kΩ 21 6 T2 3 T3 T2OUT 6 T2 T2IN 20 1 T3 T3OUT T3IN T4IN R1OUT T4 20 7 R1 5kΩ 21 8 T4 28 9 T4OUT R1IN R1 5 R2OUT 5kΩ 4 R2IN 4 R2OUT R2 22 R3OUT R3 17 R4OUT R4 GND 8 5kΩ 5kΩ 5kΩ 3 R2IN R2 26 R3OUT 5kΩ 27 R3IN 23 R3IN R3 22 R4OUT 5kΩ 23 R4IN 16 R4IN R4 19 R5OUT 24 EN GND 10 R5 5kΩ 18 R5IN 5kΩ 25 SD 3-6 HIN201 thru HIN213 Pinouts (Continued) HIN213 (SOIC, SSOP) TOP VIEW T3OUT 1 T1OUT 2 T2OUT 3 R2IN 4 R2OUT 5 T2IN 6 T1IN 7 R1OUT 8 R1IN 9 GND 10 VCC 11 C1+ 12 V+ 13 C1- 14 28 T4OUT 27 R3IN 26 R3OUT 25 SD 24 EN 23 R4IN 22 R4OUT 21 T4IN 20 T3IN 19 R5OUT 18 R5IN 17 V16 C215 C2+ T4IN R1OUT T3IN 20 T2IN 6 T1IN 0.1µF 0.1µF 12 C1+ + 14 C115 C2+ + 16 C2+5V 11 VCC +5V TO 10V VOLTAGE DOUBLER +10V TO -10V VOLTAGE INVERTER T1 V+ 13 + 0.1µF V- 17 + 2 0.1µF T1OUT +5V 400kΩ 7 +5V 400kΩ +5V 400kΩ +5V 400kΩ T2 3 T3 T2OUT 1 T3OUT 21 8 T4 28 9 T4OUT R1IN NOTE: R4 and R5 active in shutdown. 5 R2OUT R1 5kΩ 4 R2IN R2 26 R3OUT R3 22 R4OUT R4 19 R5OUT 24 EN GND 10 R5 5kΩ 27 R3IN 5kΩ 23 R4IN 5kΩ 18 R5IN 5kΩ 25 SD 3-7 HIN201 thru HIN213 Absolute Maximum Ratings VCC to Ground. . . . . . . . . . . . . . . . . . . . . . (GND -0.3V)