HS-390RH883S

HS-302RH/883S, HS-303RH/883S, HS-306RH/883S, HS-307RH/883S, HS-384RH/883S, HS-390RH/883S September 1995 Radiation Hardened CMOS Analog Switches Description The HS-3XXRH/883S family of analog switches are monolithic devices fabricated using Radiation Hardened CMOS technology and the Intersil dielectric isolation process for latch-up free operation. Improved total dose hardness is obtained by layout (thin oxide tabs extending to a channel stop) and processing (hardened gate oxide). These switches offer low-resistance switching performance for analog voltages up to the supply rails. “ON” resistance is low and stays reasonably constant over the full range of operating voltage and current. “ON” resistance also stays reasonably constant when exposed to radiation, being typically 30Ω pre-rad and 35Ω post 100K RAD-Si. All devices provide break-before-make switching. The 6 devices in this switch series are differentiated by type of switch action, pinout and digital logic levels. The HS-302/ 303/384/390RH/883S switches have 5V digital inputs while the HS-306/307RH/883S switches have 15V digital inputs. All devices are available in Ceramic Flatpack and SBDIP packages. The HS-3XXRH/883S switches can directly replace the HI-3XX series devices. Features • This Circuit is Processed in Accordance to Mil-Std883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. • Radiation Hardened - Functional Total Dose Exceeds 1 x 105 RAD Si • Pin for Pin Compatible with Intersil HI-3XX Series Analog Switches • Analog Signal Range 15V • Low Leakage • Low RON • No Latch Up • Versions for 5V and 15V Digital Systems • Low Operating Power • Military Temperature Range -55oC to +125oC Applications • Sample and Hold i.e. Low Leakage Switching • Op Amp Gain Switching i.e. Low ON Resistance • Switched Capacitor Filters • Low Level Switching Circuits • Satellites • Nuclear Reactor Controls • Military Environments Functional Diagram IN N P D Ordering Information PART NUMBER HS1-302RH/883S HS9-302RH/883S HS1-302RH/Sample HS9-302RH/Sample HS1-303RH/883S HS9-303RH/883S HS1-303RH/Sample HS9-303RH/Sample HS1-306RH/883S ( Note 1) HS9-306RH/883S ( Note 1) TEMPERATURE RANGE -55oC to +125oC -55oC to +125oC +25oC +25oC -55oC to +125oC -55oC to +125oC +25oC +25oC -55oC to +125oC -55oC to +125oC SCREENING LEVEL Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent Sample Sample Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent Sample Sample Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent PACKAGE 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 Spec Number File Number 1 518526 3067.1 HS-3XXRH/883S Ordering Information PART NUMBER HS1-306RH/Sample (Note 1) HS9-306RH/Sample (Note 1) HS1-307RH/883S HS9-307RH/883S HS1-307RH/Sample HS9-307RH/Sample HS1-384RH/883S (Note 1) HS9-384RH/883S (Note 1) HS1-384RH/Sample (Note 1) HS9-384RH/Sample (Note 1) HS1-390RH/883S HS9-390RH/883S HS1-390RH/Sample HS9-390RH/Sample NOTE: 1. Not recommended for new design. (Continued) TEMPERATURE RANGE +25oC +25oC -55oC to +125oC -55oC to +125oC +25oC +25oC -55oC to +125oC -55oC to +125oC +25oC +25oC -55oC to +125oC -55oC to +125oC +25oC +25oC SCREENING LEVEL Sample Sample Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent Sample Sample Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent Sample Sample Intersil /883 Class S Equivalent Intersil /883 Class S Equivalent Sample Sample PACKAGE 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack 14 Lead SBDIP 14 Lead Ceramic Flatpack 16 Lead SBDIP 16 Lead Ceramic Flatpack 16 Lead SBDIP 16 Lead Ceramic Flatpack 16 Lead SBDIP 16 Lead Ceramic Flatpack 16 Lead SBDIP 16 Lead Ceramic Flatpack Pinouts (Switch States are for Logic “1” Inputs) 14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE (SBDIP) MIL-STD-1835 CDIP2-T14 TOP VIEW DUAL DPST HS-302RH/883S HS-306RH/883S NC 1 S3 2 D3 3 D1 4 S1 5 IN1 6 GND 7 14 V+ 13 S4 12 D4 11 D2 10 S2 9 IN2 8 VNC S3 D3 D1 S1 IN1 GND 16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE (SBDIP) MIL-STD-1835 CDIP2-T16 TOP VIEW DUAL DPST HS-384RH/883S D1 NC D3 S3 S4 1 2 3 4 5 6 7 8 16 S1 15 IN1 14 V13 GND 12 NC 11 V+ 10 IN2 9 S2 D1 NC D3 S3 S4 D4 NC D2 DUAL SPDT HS-303RH/883S HS-307RH/883S 1 2 3 4 5 6 7 14 V+ 13 S4 12 D4 11 D2 10 S2 9 IN2 8 V- DUAL SPDT HS-390RH/883S 1 2 3 4 5 6 7 8 16 S1 15 IN1 14 V13 GND 12 NC 11 V+ 10 IN2 9 S2 D4 NC D2 LOGIC 0 1 SWITCH 1-4 OFF ON LOGIC 0 1 SW1 SW2 OFF ON SW3 SW4 ON OFF LOGIC 0 1 SWITCH 1-4 OFF ON LOGIC 0 1 SW1 SW2 OFF ON SW3 SW4 ON OFF Spec Number 2 518526 HS-3XXRH/883S Pinouts (Switch States are for Logic “1” Inputs) (Continued) 14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE (FLATPACK) MIL-STD-1835 CDIP3-F14 TOP VIEW DUAL DPST HS-302RH/883S HS-306RH/883S 1 NC S3 D3 D1 S1 IN1 GND 2 3 4 5 6 7 14 13 12 11 10 9 8 V+ S4 D4 D2 S2 IN2 V1 NC S3 D3 D1 S1 IN1 GND 2 3 4 5 6 7 DUAL SPDT HS-303RH/883S HS-307RH/883S 14 13 12 11 10 9 8 V+ S4 D4 D2 S2 IN2 V- LOGIC 0 1 SWITCH 1 - 4 OFF ON LOGIC 0 1 SW1 AND SW2 OFF ON SW3 AND SW4 ON OFF 16 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE (FLATPACK) MIL-STD-1835 CDIP4-F16 TOP VIEW DUAL DPST HS-384RH/883S D1 NC D3 S3 S4 D4 NC D2 6 7 8 11 10 9 1 2 3 4 5 16 15 14 13 12 S1 IN1 VGND NC V+ IN2 S2 D1 NC D3 S3 S4 D4 NC D2 6 7 8 11 10 9 1 2 3 4 5 DUAL SPDT HS-390RH/883S 16 15 14 13 12 S1 IN1 VGND NC V+ IN2 S2 LOGIC 0 1 SWITCH 1 - 4 OFF ON LOGIC 0 1 SW1 AND SW2 OFF ON SW3 AND SW4 ON OFF Spec Number 3 518526 Specifications HS-3XXRH/883S Absolute Maximum Ratings Supply Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . +44V +VSUPPLY to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +22V -VSUPPLY to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-22V Analog Input Overvoltages: +VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +VSUPPLY +1.5V -VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-VSUPPLY - 1.5V Digital Input Overvoltage: +VA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+VSUPPLY +4V -VA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-VSUPPLY -4V Peak Current, S or D Pulsed at 1ms, 10% Duty Cycle Max . . . 40mA Continuous Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Lead Temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . . . ≤ +300oC Reliability Information Thermal Resistance θJA θJC 14 Lead SBDIP Package . . . . . . . . . . . . . 70oC/W 19oC/W 14 Lead Ceramic Flatpack Package . . . . 105oC/W 17oC/W 16 Lead SBDIP Package . . . . . . . . . . . . . 70oC/W 19oC/W 16 Lead Ceramic Flatpack Package . . . . 105oC/W 17oC/W Maximum Package Power Dissipation at +125oC Ambient 14 Lead SBDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.71W 14 Lead Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . 0.48W 16 Lead SBDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.71W 16 Lead Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . .0.48 If device power exceeds package dissipation capability, provide heat sinking or derate linearly at the following rate: 14 Lead SBDIP Package . . . . . . . . . . . . . . . . . . . . . . . 14.3mW/oC 14 Lead Ceramic Flatpack Package . . . . . . . . . . . . . . . 9.5mW/oC 16 Lead SBDIP Package . . . . . . . . . . . . . . . . . . . . . . . 14.3mW/oC 16 Lead Ceramic Flatpack Package . . . . . . . . . . . . . . . 9.5mW/oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Supply Voltage (± VSupply) . . . . . . . . . . . . . . . . . . . . . ±15V Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC TABLE 1. HS-302RH/303RH/384RH/390RH/883S DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0.8V GROUP A SUBGROUPS 1 2, 3 -RDS VD = -10V, IS = 10mA, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = VD = +14V, S1/S2/S3/S4 VS = VD = -14V, S1/S2/S3/S4 All Channels VA = 0.8V 1 2, 3 Leakage Current Into the Source Terminal of an “Off” Switch +IS(OFF) 1 2, 3 -IS(OFF) 1 2, 3 Leakage Current into the Drain Terminal of an “Off” Switch +ID(OFF) 1 2, 3 -ID(OFF) 1 2, 3 Leakage Current from an “On” Driver Into the Switch (Drain & Source) +ID(ON) 1 2, 3 -ID(ON) 1 2, 3 Low Level Input Address Current High Level Input Address Current IAL 1 2, 3 IAH All Channels VA = 4.0V 1 2, 3 LIMITS TEMPERATURE +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC MIN -2 -100 -2 -100 -2 -100 -2 -100 -2 -100 -2 -100 -1 -1 -1 -1 MAX 50 75 50 75 2 100 2 100 2 100 2 100 2 100 2 100 1 1 1 1 UNITS Ω Ω Ω Ω nA nA nA nA nA nA nA nA nA nA nA nA µA µA µA µA PARAMETER “Switch On” Resistance SYMBOL +RDS CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 Spec Number 4 518526 Specifications HS-3XXRH/883S TABLE 1. HS-302RH/303RH/384RH/390RH/883S DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0.8V (Continued) GROUP A SUBGROUPS 1 2, 3 VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V Negative Supply Current I(-) All Channels VA = 0.8V 1 2, 3 1 2, 3 VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V 1 2, 3 LIMITS TEMPERATURE +25oC -55oC to +125oC MIN -10 -100 -10 -100 MAX 10 100 0.5 1 UNITS µA µA mA mA µA µA µA µA PARAMETER Positive Supply Current SYMBOL I(+) CONDITIONS All Channels VA = 0.8V +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC TABLE 1. HS-306RH/307RH/883S DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +11.0V, VAL = 3.5V GROUP A SUBGROUPS 1 2, 3 +RDS VD = -10V, IS = 10mA, S1/S2/S3/S4 1 2, 3 Leakage Current Into the Source Terminal of an “Off” Switch +IS(OFF) VS = +14V, VD = -14V, S1/S2/S3/S4 1 2, 3 -IS(OFF) VS = -14V, VD = +14V, S1/S2/S3/S4 1 2, 3 Leakage Current into the Drain Terminal of an “Off” Switch +ID(OFF) VS = -14V, VD = +14V, S1/S2/S3/S4 1 2, 3 -ID(OFF) VS = +14V, VD = -14V, S1/S2/S3/S4 1 2, 3 Leakage Current from an “On” Driver Into the Switch (Drain and Source) +ID(ON) VS = VD = +14V, S1/S2/S3/S4 1 2, 3 -ID(ON) VS = VD = -14V, S1/S2/S3/S4 1 2, 3 Low Level Input Address Current IAL All Channels VA = 3.5V 1 1, 2 High Level Input Address Current IAH All Channels VA = 11V 1 1, 2 LIMITS TEMPERATURE +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC MIN -2 -100 -2 -100 -2 -100 -2 -100 -2 -100 -2 -100 -1 -1 -1 -1 MAX 50 75 50 75 2 100 2 100 2 100 2 100 2 100 2 100 1 1 1 1 UNITS Ω Ω Ω Ω nA nA nA nA nA nA nA nA nA nA nA nA µA µA µA µA PARAMETER “Switch On” Resistance SYMBOL +RDS CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 Spec Number 5 518526 Specifications HS-3XXRH/883S TABLE 1. HS-306RH/307RH/883S DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +11.0V, VAL = 3.5V (Continued) GROUP A SUBGROUPS 1 2, 3 All Channels VA = 15V 1 2, 3 Negative Supply Current I(-) All Channels VA = 0V 1 2, 3 All Channels VA = 15V 1 2, 3 LIMITS TEMPERATURE +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC MIN -10 -100 -10 -100 MAX 10 100 10 100 UNITS µA µA µA µA µA µA µA µA PARAMETER Positive Supply Current SYMBOL I(+) CONDITIONS All Channels VA = 0V TABLE 2. HS-302RH/303RH/384RH/390RH/883S AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0V GROUP A SUBGROUPS 9 10, 11 TON RL = 300Ω, VS = +3V 9 10, 11 Switch Turn “Off” Time TOFF RL = 300Ω, VS = +3V 9 10, 11 LIMITS TEMPERATURE +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC MIN 30 MAX 150 300 300 500 250 450 UNITS ns ns ns ns ns ns PARAMETER Break-Before-Make Time Delay (HS-303RH & 390RH Only) Switch Turn “On” Time SYMBOL TOPEN CONDITIONS RL = 300Ω, VS = +3V, VAH = 5V TABLE 2. HS-306RH/307RH/883S AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Guaranteed and 100% Tested. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +15.0V, VAL = 0V GROUP A SUBGROUPS 9 10, 11 TON RL = 300Ω, VS = +3V 9 10, 11 Switch Turn “Off” Time TOFF RL = 300Ω, VS = +3V 9 10, 11 LIMITS TEMPERATURE +25oC -55oC to +125oC +25oC -55oC to +125oC +25oC -55oC to +125oC MIN 30 MAX 150 300 300 500 250 450 UNITS ns ns ns ns ns ns PARAMETER Break-Before-Make Time Delay (HS-307RH Only) Switch Turn “On” Time SYMBOL TOPEN CONDITIONS RL = 300Ω, VS = +3V Spec Number 6 518526 Specifications HS-3XXRH/883S TABLE 3. HS-302RH/303RH/306RH/307RH/384RH/390RH/883S ELECTRICAL PERFORMANCE CHARACTERISTICS (NOTE 1) Unless Otherwise Specified: HS-302RH/303RH/384RH/390RH/883S V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0V HS-306RH/307RH/883S V- = -15V, V+ = +15V, VAH = +15.0V, VAL = 0V (NOTE 1) CONDITIONS Measured Source to GND VA = 0V VA = 15V Measured Drain to GND VGEN = 1Vp-p, f = 1MHz VGEN = 1Vp-p, f = 1MHz VS = GND, CL = 0.01µF LIMITS TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN 40 40 MAX 28 10 10 28 15 UNITS pF pF pF pF dB dB mV PARAMETER Switch Input Capacitance Driver Input Capacitance SYMBOL CIS(OFF) CC1 CC2 Switch Output Off Isolation Crosstalk Charge Transfer COS VISO VCR VCTE NOTE:1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. TABLE 4. HS-302RH/303RH/384RH/390RH/883S DC POST 100K RAD (Si) ELECTRICAL CHARACTERISTICS Tested Per Mil-Std-883. Unless Otherwise Specified: HS-302RH/303RH/384RH/390RH/883S V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0.8V LIMITS PARAMETER “Switch On” Resistance SYMBOL +RDS -RDS Leakage Current Into the Source Terminal of an “Off” Switch Leakage Current into the Drain Terminal of an “Off” Switch Leakage Current from an “On” Driver Into the Switch (Drain & Source) Positive Supply Current +IS(OFF) -IS(OFF) +ID(OFF) -ID(OFF) -ID(ON) -ID(ON) I(+) CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 VD = -10V, IS = 10mA, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = VD = +14V, S1/S2/S3/S4 VS = VD = -14V, S1/S2/S3/S4 All Channels VA = 0.8V VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V Negative Supply Current I(-) All Channels VA = 0.8V VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V High Level Address Current Low Level Address Current Break-Before-Make Time Delay (HS-303RH/883S and HS390RH/883S Only) Switch Turn-On Time Switch Turn-Off Time NOTES: 1. VAL = 0V; VAH = 5.0V 2. VAL = 0V; VAH = 4.0 IAH IAL TOPEN All Channels High All Channels Low RL = 300Ω, VS = +3V, (Note 1) TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN -100 -100 -100 -100 -100 -100 -100 -100 -1 -1 2 MAX 60 60 100 100 100 100 100 100 100 1 +1 +1 300 UNITS Ω Ω nA nA nA nA nA nA µA mA µA µA µA µA ns TON TOFF RL = 300Ω, VS = +3V, (Note 2) RL = 300Ω, VS = +3V, (Note 2) +25oC +25oC - 500 450 ns ns Spec Number 7 518526 Specifications HS-3XXRH/883S TABLE 4. HS-306/307RH/883S DC POST 100K RAD (Si) ELECTRICAL CHARACTERISTICS Tested Per Mil-Std-883. Unless Otherwise Specified: HS-306RH/307RH/883S V- = -15V, V+ = +15V, VAH = +11.0V, VAL = 3.5V LIMITS PARAMETER “Switch On” Resistance SYMBOL +RDS -RDS Leakage Current Into the Source Terminal of an “Off” Switch Leakage Current into the Drain Terminal of an “Off” Switch Leakage Current from an “On” Driver Into the Switch (Drain & Source) Positive Supply Current +IS(OFF) -IS(OFF) +ID(OFF) -ID(OFF) -ID(ON) -ID(ON) I(+) CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 VD = -10V, IS = 10mA, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = VD = +14V, S1/S2/S3/S4 VS = VD = -14V, S1/S2/S3/S4 All Channels VA = 0V All Channels VA = 15V Negative Supply Current I(-) All Channels VA = 0V All Channels VA = 15V High Level Address Current Low Level Address Current Break-Before-Make Time Delay (HS-307RH/883S Only) Switch Turn-On Time Switch Turn-Off Time NOTE: 1. VAL = 0V; VAH = 15V IAH IAL TOPEN TON TOFF All Channels High All Channels Low RL = 300Ω, VS = +3V, (Note 1) RL = 300Ω, VS = +3V, (Note 1) RL = 300Ω, VS = +3V, (Note 1) TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN -100 -100 -100 -100 -100 -100 -100 -100 -1 -1 2 MAX 60 60 100 100 100 100 100 100 100 1 +1 +1 300 500 450 UNITS Ω Ω nA nA nA nA nA nA µA mA µA µA µA µA ns ns ns TABLE 5. HS-302RH/303RH/384RH/390RH/883S DC POST BURN-IN DELTA ELECTRICAL CHARACTERISTICS Guaranteed, Per Mil-Std-883. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0.8V GROUP A SUBGROUPS 1 LIMITS TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN -5 MAX 5 UNITS Ω Ω nA PARAMETER “Switch On” Resistance SYMBOL +RDS CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 VD = -10V, IS = 10mA, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = VD = +14V, S1/S2/S3/S4 VS = VD = -14V, S1/S2/S3/S4 -RDS 1 -5 5 Leakage Current Into the Source Terminal of an “Off” Switch Leakage Current into the Drain Terminal of an “Off” Switch Leakage Current from an “On” Driver Into the Switch (Drain & Source) +IS(OFF) 1 -2 2 -IS(OFF) 1 -2 2 nA +ID(OFF) 1 -2 2 nA -ID(OFF) 1 -2 2 nA +ID(ON) -ID(ON) 1 1 -2 -2 2 2 nA nA Spec Number 8 518526 Specifications HS-3XXRH/883S TABLE 5. HS-302RH/303RH/384RH/390RH/883S DC POST BURN-IN DELTA ELECTRICAL CHARACTERISTICS Guaranteed, Per Mil-Std-883. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +4.0V, VAL = 0.8V (Continued) GROUP A SUBGROUPS 1 LIMITS TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC MIN -100 MAX 100 UNITS nA PARAMETER Low Level Input Address Current High Level Input Address Current Positive Supply Current SYMBOL IAL CONDITIONS All Channels VA = 0.8V IAH All Channels VA = 4.0V 1 -100 100 nA µA mA µA µA I(+) All Channels VA = 0.8V VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V 1 1 -1 -0.1 1 0.1 Negative Supply Current I(-) All Channels VA = 0.8V VA1 = 0V, VA2 = 4.0V and VA1 = 4.0V, VA2 = 0V 1 1 -1 -1 1 1 TABLE 5. HS-306RH/307RH/883S DC POST BURN-IN DELTA ELECTRICAL CHARACTERISTICS Guaranteed, Per Mil-Std-883. Unless Otherwise Specified: V- = -15V, V+ = +15V, VAH = +11.0V, VAL = 3.5V LIMITS PARAMETER “Switch On” Resistance SYMBOL +RDS CONDITIONS VD = 10V, IS = -10mA, S1/S2/S3/S4 VD = -10V, IS = 10mA, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = -14V, VD = +14V, S1/S2/S3/S4 VS = +14V, VD = -14V, S1/S2/S3/S4 VS = VD = +14V, S1/S2/S3/S4 VS = VD = -14V, S1/S2/S3/S4 All Channels VA = 3.5V GROUP A SUBGROUPS 1 TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC +25oC MIN -5 MAX 5 UNITS Ω Ω nA -RDS 1 -5 5 Leakage Current Into the Source Terminal of an “Off” Switch +IS(OFF) 1 -2 2 -IS(OFF) 1 -2 2 nA Leakage Current into the Drain Terminal of an “Off” Switch +ID(OFF) 1 -2 2 nA -ID(OFF) 1 -2 2 nA Leakage Current from an “On” Driver Into the Switch (Drain & Source) Low Level Input Address Current High Level Input Address Current Positive Supply Current +ID(ON) -ID(ON) IAL 1 1 1 -2 -2 -100 2 2 100 nA nA nA IAH All Channels VA = 11V 1 -100 100 nA µA µA µA µA I(+) All Channels VA = 0V All Channels VA = 15V 1 1 1 1 -1 -1 -1 -1 1 1 1 1 Negative Supply Current I(-) All Channels VA = 0V All Channels VA = 15V Spec Number 9 518526 Specifications HS-3XXRH/883S TABLE 6. APPLICABLE SUBGROUPS GROUP A SUBGROUPS CONFORMANCE GROUPS Initial Test Interim Test PDA Final Test Group A (Note 1) Group B Subgroup B-5 Subgroup B-6 Group D Group E, Subgroup 2 NOTES: 1. Alternate Group A testing in accordance with Method 5005 of MIL-STD-883 may be exercised. 2. Table 5 parameters on.y. METHOD 100%/5004 100%/5004 100%/5004 100%/5004 Sample/5005 Sample/5005 Sample/5005 Sample/5005 Sample/5005 TESTED 1, 7, 9 1, 7, 9, Deltas 1, 7, Deltas 2, 3, 8A, 8B, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas 1, 7, 9 1, 7, 9 1, 7 1, 2, 3, Deltas, (Note 2) RECORDED 1, (Note 2) 1, Deltas, (Note 2) Spec Number 10 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S Intersil Space Level Product Flow Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Nondestructive Bond Pull, Method 2023 Sample - Wire Bond Pull Monitor, Method 2011 Sample - Die Shear Monitor, Method 2019 or 2027 100% Internal Visual Inspection, Method 2010, Condition A 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% PIND, Method 2020, Condition A 100% External Visual 100% Serialization 100% Initial Electrical Test (T0) 100% Static Burn-In 1, Condition A or B, 72hrs. min., +125oC min. 100% Interim Electrical Test (T1) 100% Delta Calculation (T0-T1) 100% PDA, Method 5004 (Note 1) 100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or Equivalent, Method 1015 100% Interim Electrical Test (T2) 100% Delta Calculation (T0-T2) 100% PDA, Method 5004 (Note 1) 100% Final Electrical Test 100% Fine/Gross Leak, Method 1014 100% Radiographic, Method 2012 (Note 2) 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 3) Sample - Group B, Method 5005 Sample - Group D, Method 5005 100% Data Package Generation (Note 4) NOTES: 1. Failures from subgroup 1, 7 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the failures from subgroup 7. 2. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 3. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 4. Data Package Contents: • Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). • Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage. • GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. • X-Ray report and film. Includes penetrometer measurements. • Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). • Lot Serial Number Sheet (Good units serial number and lot number). • Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test. (See Table 6) • Group B and D attributes and/or Generic data. • The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative. Spec Number 11 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S Irradiation Circuits NC 1 R1 R2 R3 R4 S3 2 D3 3 D1 4 S1 5 IN1 6 GND 7 8 9 V10 IN2 V3 V2 IN1 6 GND 7 8 9 V11 S2 R5 R4 S1 5 10 IN2 V3 V2 12 D2 R6 R3 D1 4 11 S2 R5 13 D4 R7 R2 D3 3 12 D2 R6 14 S4 R8 V+ V1 R1 NC 1 S3 2 13 D4 R7 14 S4 R8 V+ V1 HS-302RH/303RH/883S HS-384RH/390RH/883S NOTES: 1. R1 - R8 = 10kΩ ± 5%, 1/4W 2. V1 = +15V ± 10% 3. V2 = -15V ± 10% 4. V3 = +5V ± 10% 5. All irradiation testing is performed in the 14 pin package. NOTES: HS-306RH/307RH/883S 1. R1 - R8 = 10kΩ ± 5%, 1/4W 2. V1 = +15V ± 10% 3. V2 = -15V ± 10% 4. V3 = +12V ± 10% 5. All irradiation testing is performed in the 14 pin package. Burn-In Circuits VA VV+ R NC 1 1 2 R 3 R 4 5 6 7 11 10 9 8 C D VR 12 R R 5 6 7 8 12 11 10 9 D C +V 14 C 13 R D V+ R 2 3 4 15 14 13 D C 16 VA -V STATIC CONFIGURATION HS-302RH/303RH/306RH/307RH/883S NOTES: 1. R = 10KΩ ± 5%, 1/4W (4 per position) 2. C = 0.01µF minimum (per position) or 0.1µF minimum per row 3. D = IN4002 (or equivalent) 4. +V = +15.5V ± 0.5V, -V = -15.5V ± 0.5V 5. VA = +15.5V ± 0.5V for 306RH/307RH 6. VA = +5.5V ± 0.5V for 302RH/303RH NOTES: STATIC CONFIGURATION HS-384RH/390RH/883S 1. R = 10KΩ ± 5%, 1/4W (4 per position) 2. C = 0.01µF minimum (per position) or 0.1µF minimum per row 3. D = IN4002 (or equivalent) 4. +V = +15.5V ± 0.5V, -V = -15.5V ± 0.5V 5. VA = +5.5V ± 0.5V Spec Number 12 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S Burn-In Circuits F V- (Continued) V+ F VV+ NC 1 2 14 C 13 R 12 R D V+ NC 1 2 14 C 13 R 12 R 11 10 9 8 C D V+ R 3 R 4 5 6 7 11 10 9 8 R 3 R 4 5 6 VC D 7 VD DYNAMIC CONFIGURATION HS-302RH/303RH/883S NOTES: 1. R = 10KΩ ± 5%, 1/4W (4 per position) 2. C = 0.01µF minimum (per position) or 0.1µF minimum per row 3. D = IN4002 (or equivalent) 4. F = 100kHz square wave, 50% duty cycle, VL = 0.8V max., VH = 5.5V ± 0.5V 5. +V = +15.5V ± 0.5V, -V = -15.5V ± 0.5V NOTES: DYNAMIC CONFIGURATION HS-306RH/307RH/883S 1. R = 10KΩ ± 5%, 1/4W (4 per position) 2. C = 0.01µF minimum (per position) or 0.1µF minimum per row 3. D = IN4002 (or equivalent) 4. F = 100kHz square wave, 50% duty cycle, VL = 0.8V max., VH = 14V ± 1V 5. +V = +15.5V ± 0.5V, -V = -15.5V ± 0.5V R 1 2 R 3 4 R 5 6 7 R 8 9 14 13 12 11 10 D D C C +V -V 16 15 F DYNAMIC CONFIGURATION HS-384RH/390RH/883S NOTES: 1. R = 10KΩ ± 5%, 1/4W (4 per position) 2. C = 0.01µF minimum (per position) or 0.1µF minimum per row 3. D = IN4002 (or equivalent) 4. F = 100kHz square wave, 50% duty cycle, VL = 0.8V max., VH = +5.5V ±0.5V 5. +V = +15.5V ± 0.5V, -V = -15.5V ± 0.5V Spec Number 13 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S Test Circuits SWITCH TYPE HS-302RH/303RH/384RH/390RH/883S HS-306RH/307RH/883S V+ +15V VO VS = +3V RL 300Ω LOGIC INPUT GND V-15V SWITCH OUTPUT LOGIC INPUT 0V VS 0V SWITCH OUTPUT tON tOFF 90% 10% VINH 4V 15V LOGIC “1” = SWITCH ON VINH 50% 50% FIGURE 1. SWITCHING TEST CIRCUIT (tON, tOFF) SWITCH TYPE HS-303RH/390RH/883S HS-307RH/883S V+ +15V VS1 = +3V VS2 = +3V RL2 LOGIC INPUT GND V-15V RL1 D1 D2 OUT 1 OUT 2 VINH 5V 15V LOGIC “1” = SWITCH ON LOGIC INPUT 0V VINH RL1 = RL2 = 300Ω 0V 0V SWITCH OUTPUT 50% 50% OUT 1 OUT 2 50% tBBM 50% tBBM FIGURE 2. BREAK-BEFORE-MAKE TEST CIRCUIT (tBBM) VA VB D S ID(OFF) A ± D S IS(OFF) A ±14V ±10V RON = VB - VA ± 10mA FIGURE 3. ON RESISTANCE TEST CIRCUIT (RON) ± 10mA ID(ON) ±14V A 14V FIGURE 4. ON LEAKAGE CURRENT TEST CIRCUIT (IDON) FIGURE 5. OFF LEAKAGE CURRENT TEST CIRCUIT (ISOFF, IDOFF) Spec Number 14 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S Metallization Topology DIE DIMENSIONS: Die Size: 2130 x 1930µm Die Thickness: 11 ±1 mils METALLIZATION: Type: Al, 12.5kÅ ± 2kÅ Back: Gold GLASSIVATION: Type: SiO2 Thickness: 8kÅ ± 1kÅ WORST CASE CURRENT DENSITY: 1.732e05 A/cm2 SUBSTRATE POTENTIAL: Unbiased PROCESS: DI Linear Metal Gate CMOS Metallization Mask Layout HS-302RH/303RH/306RH/307RH/883S S3 V+ S4 D3 D4 D1 D2 S1 S2 IN1 IN2 GND NC HS-384RH/390RH/883S IN1 D3 D1 S1 S3 V- VGND S4 V+ IN2 D4 D2 S2 Spec Number 15 518526 HS-302RH/303RH/306RH/307RH/384RH/390RH/883S All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Spec Number 16