HS9-201HSRH-8

® HS-201HSRH Data Sheet March 24, 2006 FN4874.1 Radiation Hardened High Speed, Quad SPST, CMOS Analog Switch The HS-201HSRH is a monolithic CMOS analog switch featuring power-off high input impedance, very fast switching speeds and low ON resistance. Fabrication on our DI RSG process assures SEL immunity and only very slight sensitivity to low dose rate (ELDRS). These Class V/Q devices are tested and guaranteed for 300krad (Si) total dose performance. Power-off high input impedance enables the use of this device in redundant circuits without causing data bus signal degradation. ESD protection, overvoltage protection, fast switching times, low ON resistance, and guaranteed radiation hardness, make the HS-201HSRH ideal for any space application where improved switching performance is required. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center (DSCC). The SMD numbers listed here must be used when ordering flight units. Detailed electrical specifications for this device are contained in SMD 5962-99618. A ”hot-link” is provided on our homepage for downloading. www.intersil.com/spacedefense/space.asp Features • Electrically Screened to DSCC SMD 5962-99618 • QML Qualified per MIL-PRF-38535 • Radiation Performance - Guaranteed Total Dose Performance . . . . . 300krad (Si) - SEL Immune. . . . . . . . . . . . . . . . . . . . .DI RSG Process • Overvoltage Protection (Power On, Switch Off) . . . . . . ±30V • Power Off High Impedance . . . . . . . . . . . . . . . . . . . ±17V • Fast Switching Times - tON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110ns (Max) - tOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80ns (Max) • Low “ON” Resistance . . . . . . . . . . . . . . . . . . . 50Ω (Max) • Pin Compatible with Industry Standard 201 Types • Operating Supply Range . . . . . . . . . . . . . . . . . ±10V to ±15V • Wide Analog Voltage Range (±15V Supplies) . . . . . . . ±15V • TTL Compatible Applications • High Speed Multiplexing • Sample and Hold Circuits • Digital Filters Pinout HS1-201HSRH, SBDIP (CDIP2-T16) HS9-201HSRH, FLATPACK (CDFP4-F16) TOP VIEW A1 1 OUT1 2 IN1 3 V- 4 GND 5 IN4 6 OUT4 7 A4 8 16 A2 15 OUT2 14 IN2 13 V+ 12 NC 11 IN3 10 OUT3 9 A3 • Operational Amplifier Gain Switching Networks • Integrator Reset Circuits 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2000, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HS-201HSRH Ordering Information ORDERING NUMBER 5962F9961801VEC 5962F9961801QEC 5962F9961801VXC 5962F9961801QXC 5962F9961801V9A HS1-201HSRH/PROTO HS9-201HSRH/PROTO INTERNAL MKT. NUMBER HS1-201HSRH-Q HS1-201HSRH-8 HS9-201HSRH-Q HS9-201HSRH-8 HS0-201HSRH-Q HS1-201HSRH/PROTO HS9-201HSRH/PROTO PART MARKING Q 5962F9961801VEC Q 5962F9961801QEC Q 5962F9961801VXC Q 5962F9961801QXC HS1-201HSRH/PROTO HS9-201HSRH/PROTO TEMP. RANGE (°C) -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 PACKAGE 16 Ld SBDIP 16 Ld SBDIP 16 Ld Flatpack 16 Ld Flatpack 16 Ld SBDIP 16 Ld Flatpack PKG. DWG. # D16.3 D16.3 K16.A K16.A D16.3 K16.A Die Characteristics DIE DIMENSIONS 2790µm x 4950µm (110 mils x 195 mils) Thickness: 483µm ±25.4µm (19 mils ±1 mil) INTERFACE MATERIALS Glassivation Type: Phosphorus Silicon Glass (PSG) Thickness: 8.0kÅ +/-1.0kÅ Metallization Type: Ti/AlCu Thickness: 16.0kÅ +/- 2kÅ Substrate Rad Hard Silicon Gate, Dielectric Isolation Backside Finish Silicon ASSEMBLY RELATED INFORMATION Substrate Potential Unbiased (DI) ADDITIONAL INFORMATION Worst Case Current Density