HS9-82C08RH-Q

HS-82C08RH TM Data Sheet August 2000 File Number 3040.3 Radiation Hardened 8-Bit Bus Transceiver The Intersil HS-82C08RH is a radiation-hardened octal bus transceiver with three-state outputs. It is manufactured using a self-aligned, junction isolated CMOS process and is designed for use with the HS-80C08RH radiation-hardened microprocessor. The HS-82C08RH allows asynchronous two-way communication between data buses. The direction of data flow is determined by the logic level on the transmit/receive (T/R) input. A logic high on the T/R input specifies data flow from Port A to Port B of the device. Conversely, a logic low on the T/R input specifies data flow from Port B to Port A. The Output Enable input disables both ports by placing them in the high impedance state. The HS-82C08RH is ideally suited for a wide variety of buffering applications in radiation-hardened microcomputer systems. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. Detailed Electrical Specifications for these devices are contained in SMD 5962-95714. A “hot-link” is provided on our homepage for downloading. www.intersil.com/spacedefense/space.asp Features • Electrically Screened to SMD # 5962-95714 • QML Qualified per MIL-PRF-38535 Requirements • Radiation Performance - Total Dose. . . . . . . . . . . . . . . . . . . . . 100 krad(Si) (Max) - Latch-Up Immune EPI-CMOS . . . . . >1 x 1012 rad(Si)/s • Bidirectional Three-State Input/Outputs • Low Propagation Delay Time • Low Power Consumption • Single Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . +5V • Electrically Equivalent to Sandia SA2997 • Military Temperature Range . . . . . . . . . . . -55oC to 125oC Ordering Information ORDERING NUMBER 5962R9571401QRC 5962R9571401QXC 5962R9571401VRC 5962R9571401VXC INTERNAL MKT. NUMBER HS1-82C08RH-8 HS9-82C08RH-8 HS1-82C08RH-Q HS9-82C08RH-Q TRUTH TABLE INPUTS OPERATION TRANSMIT /RECEIVE 0 1 X PORT A Out In High Z PORT B In Out High Z TEMP. RANGE (oC) -55 to 125 -55 to 125 -55 to 125 -55 to 125 Functional Diagram A0 B0 OUTPUT ENABLE 0 A1 A2 A3 PORT A4 A A5 A6 A7 B1 B2 B3 B4 PORT B B5 B6 B7 0 1 X = Don’t Care T/R OE 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000 HS-82C08RH Pinouts 20 LEAD CERAMIC DUAL-IN-LINEMETAL-SEAL PACKAGE (SBDIP) MIL-STD-1835, CDIP2-T20 TOP VIEW A0 A1 A2 A3 A4 A5 A6 A7 OE 1 2 3 4 5 6 7 8 9 20 VDD 19 B0 18 B1 17 B2 16 B3 15 B4 14 B5 13 B6 12 B7 11 T/R 20 LEAD CERAMIC METAL SEALFLATPACK PACKAGE (FLATPACK) MIL-STD-1835, CDFP4-F20 TOP VIEW A0 A1 A2 A3 A4 A5 A6 A7 OE GND 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VDD B0 B1 B2 B3 B4 B5 B6 B7 T/R GND 10 PIN A0-A7 B0-B7 DESCRIPTION Local Bus Data I/O Pins System Bus Data I/O Pins PIN T/R OE DESCRIPTION Transmit/Receive Input Active Low Output Enable Logic Diagram A0 1 TSB TSB A1 2 TSB TSB A2 3 TSB TSB A3 4 TSB TSB A4 5 TSB TSB A5 OE 9 6 B ENABLE A6 T/R11 A7 8 7 A ENABLE TSB TSB TSB TSB 12 B7 TSB TSB 13 B6 14 B5 15 B4 16 B3 17 B2 18 B1 19 B0 NOTE: An Important caveat that is applicable to CMOS devices in general is that unused inputs should never be left floating. This rule applies to inputs connected to a three-state bus. The need for external pull-up resistors during three-state bus conditions is eliminated by the presence of regenerative latches on the following HS-82C08RH pins. A0-7 and B0-7 The functional block diagram depicts one of these pins with the regenerative latch. When the CMOS driver assumes the high impedance state, the latch holds the bus in whatever logic state (high or low) it was before the threestate condition. A transient drive current of ±1.5mA at VDD/2 ±0.5V for 10ns is required to switch the latch. Thus, CMOS device inputs connected to the bus are not allowed to float during three-state conditions. 2 HS-82C08RH Switching Time Waveforms tr INPUT AN OR BN VDD 0V VDD 0V tr = tf ≤ 20ns 10% TO 90% 0.5VDD tPLH 0.5VDD 0.5VDD tPHL 0.5VDD DEVICE UNDER TEST TEST POINTS CL (NOTE) tf OUTPUT BN OR AN NOTE: CL includes stray and jig capacitance. FIGURE 1. PORT TO PORT FIGURE 2. AC TESTING LOAD CIRCUIT VDD INPUT OE 0V PORT OUTPUT tr 0.5VDD 0.1VDD tr = tf ≤ 20ns 10% TO 90% tf 0.5VDD VOH tPHZ tPLZ 0V tPZH 0.5VDD VDD 0.5VDD tPZL 0.1VDD PORT OUTPUT VOL FIGURE 3. OE TO HIGH-IMPEDANCE, OE TO PORT OUTPUT 3 HS-82C08RH Die Characteristics DIE DIMENSIONS: 76.0 mils x 89.4 mils x 14 mils ±1 mil INTERFACE MATERIALS: Glassivation: Type: SiO2 Thickness: 8kÅ ±1kÅ Top Metallization: Type: Si - Al Thickness: 11kÅ ±2kÅ Metallization Mask Layout HS-82C08RH (20) VDD (1) A0 (19) B0 A1 (2) (18) B1 A2 (3) (17) B2 A3 (4) (16) B3 A4 (5) (15) B4 A5 (6) (14) B5 A6 (7) (13) B6 A7 (8) GND (10) T/R (9) OE (9) (12) B7 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil Ltd. 8F-2, 96, Sec. 1, Chien-kuo North, Taipei, Taiwan 104 Republic of China TEL: 886-2-2515-8508 FAX: 886-2-2515-8369 4