ISL29125EVAL1Z

USER MANUAL ISL29125EVAL1Z AN1914 Rev 4.0 May 12, 2021 Evaluation Hardware/Software User Manual for RGB Sensor Introduction Reference Documents The RGB Evaluation Kit is designed to evaluate the performance of the RGB sensor. The kit is accompanied by a Graphical User Interface (GUI) that contains the CIE 1931 Chromaticity diagram with Planckian locus in an x, y- coordinate system, with cross marks to point out where the RGB sensor position is on the graph. The GUI facilitates evaluation of parameters such as raw data of Red, Green and Blue as well as X, Y and Z corrected lux measurements and also performs interrupt functions. Data can be viewed on the GUI and/or saved to a text file for future analysis. The GUI software is compatible with Windows XP®, Windows Vista®, Windows® 7 and Windows® 8. This provides a simple user interface for exercising the device features. RGB Chroma Meter Setup The system (MCU, DUT) is powered directly from the universal serial bus (USB) or from a single-supply voltage of 2.25V to 3.6V. The evaluation board must be connected to a computer through the mini USB port for the system to function. The system uses a USB MCU to communicate to the DUT via I2C/SMBus interface. Linear Regression Standard Illuminants Chromaticity Color temperature Planckian locus Colour & Vision Research laboratory Mired CIELUV Least Squares CIE 1960 Color Space (MacAdam - uv) Wratten Number Evaluation Package (Online Order) The package consists of the hardware, software and documentation listed in the following: • User Guide (Online) • ISL29125 Datasheet (Online) • Presentation (Installer File) • uv-xy table (Installer File) • CCM Calibration Worksheet (Installer File) • User Guide (Installer File) Hardware Requirements • Mini USB cable • Evaluation board Installation of the Graphical User Interface (GUI) Software and USB Driver Download the software from the ISL29125EVAL1Z page. FIGURE 1. EVALUATION BOARD Ordering Information PART NUMBER ISL29125EVAL1Z AN1914 Rev 4.0 May 12, 2021 DESCRIPTION Evaluation Board Once the application is downloaded from the website, double-click the file to start installing the GUI. The user will be greeted by the screen shown in Figure 2. Continue through the installer and read the instructions. Figures 2 through 6 show the complete installation process. The USB evaluation board should always be connected via the USB until the installation has been satisfactorily completed. Page 1 of 8 © 2014 Renesas Electronics ISL29125EVAL1Z The installation program places the user interface software in the directory indicated in Figure 5. FIGURE 2. INSTALLATION WELCOME SCREEN FIGURE 5. INSTALLATION DESTINATION LOCATION SCREEN FIGURE 3. INSTALLATION FOLDER LOCATION SCREEN FIGURE 6. INSTALLATION COMPLETE SCREEN FIGURE 4. INSTALLATION LICENSE AGREEMENT SCREEN AN1914 Rev 4.0 May 12, 2021 Page 2 of 8 ISL29125EVAL1Z Running Program for the RGB GUI A) USB Communication (Hardware) - Gather the required materials and connect the PC to the ISL29125 by mini USB cable as shown in Figure 7. C) Once “ChromaMeter” is clicked, the window displayed in Figure 9 should open. If it does not display cross-points in the Chromaticity diagram on the right and numbers on the left panel of GUI, then check your connections. If the problem still persists, then you may want to restart the software. Figure 12 shows the error message that displays if the evaluation board is improperly attached. FIGURE 7. ISL29125 EVALUATION BOARD CONNECTED TO PC BY MINI USB Once the evaluation board is connected to the PC, D6, which is next to mini USB socket at the bottom of evaluation board, should light up. If the LED is not ON, please check your connection. B) Launching the RGB GUI - Once the installation is complete, click “Finish” to launch the RGB GUI. If you wish to launch from your PC desktop, us the path shown in Figure 8. (Start  Program Intersil RGB Chroma Meter  Chroma Meter. FIGURE 9. CHROMA TEST GUI D) Figure 9 shows an example using the ISL29125. Please note that all demonstrations within this document use the ISL29125. A detailed explanation of the operating modes can be found in the datasheet of the individual devices and Figure 10 details the GUI display. FIGURE 8. INSTALLATION READY TO INSTALL SCREEN AN1914 Rev 4.0 May 12, 2021 Page 3 of 8 ISL29125EVAL1Z 12. Lux display shows corrected lux which has been transformed to equal Y. CCT displays shows color temperature of light source. 13. Raw ADC output code. 14. RMS noise of raw RGB values in %/value. 15. Card/DUT FSR: Full scale (in Lux) of the evaluation card and the sensor (internal to the card). 16. Speed: Allows the user to select the number of ADC bits and the speed of the conversion. Details shown in Figure 9. 2 3 4 5 6 16 bits, 25ms 12 bits, 6ms 12 bits, 1.5ms 8 bits, 400µs 8 bits, 100µs 1 16 bits, 100ms FIGURE 11. OPTICAL SENSOR SPEED MODE SELECTION E) The values displayed on the main panel include: •Calibrated Lux and CCT measurements •X, Y, Z values •xy coordinates •uv coordinates •RGB ADC output codes and noise levels FIGURE 10. GUI DISPLAY DETAILS 1. CCM: Allows user load new coefficients if they have a custom system setup. 2. Run button: By default sensor will run continuously. When pressed, data will be held at the last value. 3. Auto button: Auto ranges from range0 to range1 or once it is toggled to “Fixed” Then sensor can do single range depending on user selection. 4. Compensation: Scroll-bar allows user to set compensation value for sensor under different light sources. Display window shows compensation value. Range is between 0 through 127. 5. xy button: Shows Planckian locus graph in xy coordinate system on the right hand side (colored graph) or, once it is toggled, then uv-coordinates will be displayed (colored graph). F) Once the evaluation board and GUI are operating, the cross-points will start moving along the blackbody curve. By changing the color temperature of the light-bulbs, the cross-points will move along with that temperature. For example, if the user uses CL-200 (color lux meter) to measure color temperature and certain lux level of an illuminant (3200K) then takes the CL-200 out and replaces with the evaluation board, the cross-points and lux value on the GUI will be around 3200K of the black body curve and lux value will be matched with the lux that is read at CL-200. The user can continue testing the board by changing the color temperature bulb (2800K to 6500K). G) Exit the GUI by clicking the “X” button on the top right corner of the GUI. 6. Selects between normal and maximum high sensitivity on the low range only. 7. Enables 32 sample averaging. 8. Allows user to change absolute gain of corrected lux value to match the Lux Meter (CL-200 or T-10). The absolute gain can be changed to ±500%. 9. Raw data of Red, Green and Blue read from ISL29125 in percentage of full scale per range. 10. dIR: percentage IR value changes relative to full scale from compensation = 0. The higher IR value in the display window means sensor is under stronger IR-content lamp. 11. XYZ displays show corrected value Lux value, which transfers from raw RGB to XYZ. xy/uv displays show corrected xy/uv coordinate system of sensor to Planckian locus. AN1914 Rev 4.0 May 12, 2021 Page 4 of 8 ISL29125EVAL1Z Troubleshoot 1 13 14 15 2 3 16 4 5 17 6 7 18 8 9 10 11 12 FIGURE 13. EEPROM LOAD CCM (CORRECTION COLOR MATRIX) FILE FIGURE 12. USB CONNECTED ERROR OR EEPROM FILE DOES NOT LOAD 1. If installer does not complete, check the USB to make sure the evaluation board is connected to the PC. 2. If the cross-point does not display to match with the color temperature light bulb, the user needs to check x, y and z values at left GUI panel. If x, y and z are all -1, Color Correction Matrix (CCM) did not load properly. The user should click on the “CCM” button at top left corner in the GUI Panel. Another pop-up window will display as shown in Figure 13. 3. To open the CCM Worksheet, go to the “Start” menu, (Start  Intersil RGB Chroma Meter  Chroma Meter CCM Worksheet). The CCM Worksheet contains the coefficient for the specific evaluation board (Figure 8, but choose CCM Worksheet Excel). 4. Once the CCM Excel Worksheet is opened, the user should look for the worksheet number which is matched with his/her evaluation board number. Detailed explanation of the CCM PANEL can be found in the following: 1. New 2. Hardware Read 3. Hardware Write 4. Address Select 5. Byte/Word Address mode 6. Fuse/Reg Select 7. Fuse Trim: MSB Nibble (ALL - Coarse) ±22% (3% resolution) 8. Copy Fuse set to Reg 9. Fuse Trim: LSB Nibble (R&B Only - Fine) ±6% (0.8% resolution) 10. File Read 11. File Write 12. File Delete 13. Drive select 14. Directory select 5. User should copy the CCM, which is highlighted in Green color “EEPromVersion3” then paste into item 14 shown in Figure 13. 15. File Select 6. Click “Write” at item 3 then “Read” at Item 2 to configure the EEPROM on the evaluation board. 18. Calibration values 7. Click “Write” at item 7 then “Read” at item 6 to save CCM into file. AN1914 Rev 4.0 May 12, 2021 16. File display/edit 17. Header contents (read only) For other questions, comments, and feedback, contact the local Renesas FAE/Sales team. Page 5 of 8 ISL29125EVAL1Z ISL29125EVAL1Z Bill of Materials REFERENCE DESIGNATOR QTY UNITS 8 ea C1, C2, C3, C4, C5, C12, C13, C17 CAP, SMD, 0402, 0.1µF, 50V, 10%, X7R, ROHS TDK C1005X7R1H104K 6 ea C6, C7, C8, C9, C10, CAP, SMD, 0402, 1.0µF, 25V, 10%, X5R, ROHS C18 TDK CGB2A1X5R1E105K033BC 1 ea C15 CAP, SMD, 0402, 0.47µF, 25V, 10%, X5R, ROHS TDK C1005X5R1E474K050BB 2 ea C14, C16 CAP, SMD, 0805, 10µF, 10V, 10%, X5R, ROHS MUR GRM21BR61A106KE19L 6 ea GND, INT, REXT, SCL, CONN-TURRET, TH, SWAGE MNT, 0.230LENGTH, ROHS MILL-MAX SDA, VDD 2110-2-00-80-00-00-07-0 3 ea JP1, P2, VDD to 3.3V CONN-HEADER, 1X2, RETENTIVE, 2.54mm, 0.230 X 0.120, ROHS BERG/FCI 69190-202HLF 2 ea JAE ELECTRONICS DX2R005HN2E700 3 ea 1 ea D5 LED, SMD, 0805, RED/CLEAR, 2V, 20mA, 631nm, 54mcd, ROHS LITEON/VISHAY LTST-C170KRKT 1 ea D4 LED, SMD, 0805, BLUE/CLEAR, 3.4V, 20mA, 468nm, 30mcd, ROHS LITEON/VISHAY LTST-C171TBKT 2 ea D3, D6 1 ea 1 J1 DESCRIPTION CONN-USB RECEPTACLE, SMD, 5P, MINI B, R/A, ROHS MANUFACTURER JP1, P2, VDD to 3.3V CONN-JUMPER, SHORTING, 2PIN, BLACK, GOLD, ROHS SULLINS MANUFACTURER PART SPC02SYAN LED, SMD, 0805, GREEN, 2.1V, 20mA, 567nm, 6.4mcd, STANLEY ELECTRIC ROHS PG1112H-TR U5 IC-1.7V SERIAL EEPROM, 2k-BIT I2C, 8P, TDFN, ROHS MICROCHIP TECHNOLOGY 24AA024HT-I/MNY ea U1 IC-USB µCONTROLLER, 32P, LQFP, HID-REV1 PROGRAM, ROHS SILICON LABORATORIES C8051F320-GQ 1 ea U4 IC-DIGITAL LIGHT SENSOR, 6P, ODFN, 1.5x1.6, ROHS INTERSIL ISL29125IROZ 1 ea U2 IC-1A LDO REGULATOR, SMD, SOT-223, 3.3V, ROHS, Pb-free NATIONAL SEMICONDUCTOR LM3940IMP-3.3/NOPB 1 ea U3 IC-SINGLE USB PORT TVS, SMD, 6P, SOT-23-6, ROHS TEXAS INSTRUMENTS SN65220DBVR 2 ea R3, R4 RES, SMD, 0402, 0Ω, 1/16W, 5%, TF, ROHS VENKEL CR0402-16W-00T 2 ea R5, R6 RES, SMD, 0402, 1k, 1/16W, 1%, TF, ROHS VENKEL CR0402-16W-102JT 1 ea R9 RES, SMD, 0402, 10k, 1/16W, 1%, TF, ROHS PANASONIC ERJ-2RKF1002X 1 ea RNC1 RES, SMD, 0402, 100k, 1/16W, 1%, TF, ROHS PANASONIC ERJ2RKF1003 1 ea R_INT1 RES, SMD, 0402, 300Ω, 1/16W, 1%, TF, ROHS VISHAY/DALE CRCW0402300RFKED 2 ea R1, R2 RES, SMD, 0402, 4.7k, 1/16W, 1%, TF, ROHS VENKEL CR0402-16W-4701FT 1 ea R8 RES, SMD, 0402, 499Ω, 1/10W, 1%, TF, ROHS PANASONIC ERJ-2RKF4990X AN1914 Rev 4.0 May 12, 2021 Page 6 of 8 ISL29125EVAL1Z Sensor Carrier Board Silkscreen and Schematic FIGURE 14. TOP AND BOTTOM SILKSCREEN FIGURE 15. OPTICAL SENSOR CARRIER EVALUATION BOARD SCHEMATIC AN1914 Rev 4.0 May 12, 2021 Page 7 of 8 ISL29125EVAL1Z Revision History REVISION DATE 4.0 May 12, 2021 AN1914 Rev 4.0 May 12, 2021 DESCRIPTION Updated links throughout. Added Revision History section. Page 8 of 8 IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.