0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
ISL6549CBZR5213

ISL6549CBZR5213

  • 厂商:

    RENESAS(瑞萨)

  • 封装:

    SOIC14_150MIL

  • 描述:

    IC REG DL BCK/LINEAR 14-SOIC

  • 数据手册
  • 价格&库存
ISL6549CBZR5213 数据手册
DATASHEET ISL6549 Single 12V Input Supply Dual Regulator —Synchronous Rectified Buck PWM and Linear Power Controller FN9168 Rev 2.00 September 22, 2006 The ISL6549 provides the power control and protection for two output voltages in high-performance applications. The dual-output controller drives two N-Channel MOSFETs in a synchronous rectified buck converter topology and one N-Channel MOSFET in a linear configuration. The controller is ideal for applications where regulation of both the processing unit and memory supplies is required. Features The synchronous rectified buck converter incorporates simple, single feedback loop, voltage-mode control with fast transient response. Both the switching regulator and linear regulator provide a maximum static regulation tolerance of ±1% over line, load, and temperature ranges. Each output is user-adjustable by means of external resistors. • Small converter size - Adjustable frequency 150kHz to 1MHz - Small external component count An integrated soft-start feature brings both supplies into regulation in a controlled manner. Each output is monitored via the FB pins for undervoltage events. If either output drops below 75% of the nominal output level, both converters are shut off and go into retry mode. • PWM and linear output voltage range: down to 0.8V • Single 12V bias supply (no 5V supply is required) • Provides two regulated voltages - One synchronous rectified buck PWM controller - One linear controller • Both controllers drive low cost N-Channel MOSFETs • Excellent output voltage regulation - Both outputs: ±1% over temperature • 12V down conversion • Simple single-loop voltage-mode PWM control design • Fast PWM converter transient response - High-bandwidth error amplifier The ISL6549 is available in a 14 Ld SOIC package, 16 Ld QSOP, or 16 Ld 4x4 QFN packages. • Undervoltage fault monitoring on both outputs Related Literature Applications • Technical Brief TB363 Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs) • Processor and memory supplies • ASIC power supplies • Pb-free plus anneal available (RoHS compliant) • Embedded processor and I/O supplies • DSP supplies Ordering Information PART NUMBER PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL6549CB ISL6549CB 0 to 70 14 Ld SOIC M14.15 ISL6549CBZ (Note) 6549CBZ 0 to 70 14 Ld SOIC (Pb-free) M14.15 ISL6549CR ISL6549CR 0 to 70 16 Ld 4x4 QFN L16.4x4 ISL6549CRZ (Note) 6549CRZ 0 to 70 16 Ld 4x4 QFN (Pb-free) L16.4x4 ISL6549CA ISL6549CA 0 to 70 16 Ld QSOP M16.15A ISL6549CAZ (Note) 6549CAZ 0 to 70 16 Ld QSOP (Pb-free) M16.15A ISL6549CAZA (Note) 6549CAZ 0 to 70 16 Ld QSOP (Pb-free) M16.15A ISL6549IBZ (Note) 6549IBZ -40 to 85 14 Ld SOIC (Pb-free) M14.15 ISL6549IRZ (Note) 6549IRZ -40 to 85 16 Ld 4x4 QFN (Pb-free) L16.4x4 ISL6549IAZ (Note) 6549IAZ -40 to 85 16 Ld QSOP (Pb-free) M16.15A ISL6549LOW-EVAL1 Evaluation Board 1-5A ISL6549HI-EVAL1 Evaluation Board up to 20A Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets, molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN9168 Rev 2.00 September 22, 2006 Page 1 of 18 ISL6549 Pinouts LDO_DR 5 11 LGATE 10 PVCC5 LDO_FB 6 9 VCC5 GND 7 8 VCC12 FB 2 LDO_DR 3 LDO_FB 4 PHASE 15 14 13 METAL GND PAD (BOTTOM) 5 6 7 8 VCC12 12 PGND FB 4 1 UGATE COMP 3 COMP 16 VCC12 13 PHASE BOOT 14 UGATE DGND BOOT 1 FS_DIS 2 FS_DIS ISL6549 (QFN) TOP VIEW AGND ISL6549 (SOIC) TOP VIEW ISL6549 (QSOP) TOP VIEW 12 PGND 11 LGATE 10 PVCC5 9 VCC5 BOOT 1 2 3 FS_DIS COMP FB LDO_DR LDO_FB AGND DGND 4 5 6 7 8 16 UGATE 15 PHASE 14 PGND 13 LGATE 12 PVCC5 11 VCC5 10 VCC12 9 VCC12 Block Diagram VCC5 VCC12 POWER-ON VOLTAGE REFERENCE 5V REGULATOR RESET (POR) PVCC5 LDO_DR RESTART 0.60V 0.80V LDO_FB BOOT SOFT-START UGATE EA2 DIS INHIBIT SOFT-START PHASE GATE LOGIC PWM EA1 DIS FS_DIS COMP LGATE OSCILLATOR PGND GND UV1 UV2 FB FN9168 Rev 2.00 September 22, 2006 COMP Page 2 of 18 ISL6549 Simplified Power System Diagram +VIN1 +12V +VIN2 Q1 Q3 VOUT2 + LINEAR CONTROLLER PWM CONTROLLER VOUT1 + Q2 ISL6549 Typical Application Schematic +VIN1 +12V CBP12 PVCC5 CBP VCC12 + VCC5 +VIN2 CVIN2 + CVIN1 BOOT CBP5 CBOOT UGATE Q3 LDO_DR VOUT2 LDO_FB + COUT2 Q1 LOUT PHASE LGATE Q2 VOUT1 + COUT1 ISL6549 FB FS_DIS GND FN9168 Rev 2.00 September 22, 2006 COMP PGND Page 3 of 18 ISL6549 Absolute Maximum Ratings Thermal Information VCC12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +14V PVCC5, VCC5 . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +7V VCC5 (if used with external supply). . . . . . . . . . . GND - 0.3V to +6V BOOT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +27V PHASE. . . . . . . . . . . . . . . . . . . . . . . . VBOOT - 7V to VBOOT + 0.3V VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V UGATE. . . . . . . . . . . . . . . . . . . . . . VPHASE - 0.3V to VBOOT + 0.3V LGATE . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to PVCC5 + 0.3V LDO_DR . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VCC12 + 0.3V FB, LDO_FB, COMP, FS_DIS . . . . . . . GND - 0.3V to VCC5 + 0.3V ESD Classification Human Body Model (Per JESD22-A114C) . . . . . . . . . . . . . . Class 2 Machine Model (Per EIA/JESD22-A115-A) . . . . . . . . . . . . . .Class B Charge Device Model (Per JESD22-C101C). . . . . . . . . . . . Class IV Thermal Resistance JA (°C/W) JC (°C/W) SOIC Package (Note 1) . . . . . . . . . . . . 105 N/A QFN Package (Notes 2, 3). . . . . . . . . . 52 14 QSOP Package (Note 1) . . . . . . . . . . . 110 N/A Maximum Junction Temperature (Plastic Package) . . . . . . +150°C Maximum Storage Temperature Range. . . . . . . . . -65°C to +150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C (SOIC - Lead Tips Only) Recommended Operating Conditions External Supply Voltage on VCC5 . . . . . . . . . . . . . . . . . . +5.0V ±5% Supply Voltage on VCC12 . . . . . . . . . . . . . . . . . . . . . . . +12V ±10% Ambient Temperature Range (C). . . . . . . . . . . . . . . . . . 0°C to 70°C Ambient Temperature Range (I) . . . . . . . . . . . . . . . . -40°C to +85° Junction Temperature Range. . . . . . . . . . . . . . . . . . . 0°C to +125°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 3. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Recommended Operating Conditions, unless otherwise noted. VCC12 = 12V Temperature = 0 to +70°C (typical = +25°C) for Commercial; Temperature = -40 to + 85°C (typical = +25°C) for Industrial. Refer to Block Diagram, Simplified Power System Diagram, and Typical Application Schematic. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS VCC SUPPLY CURRENT Nominal Supply Current VCC12 (disabled) ICC12 dis UGATE, LGATE and LDO_DR open; FS_DIS = GND 2 3 mA Nominal Supply Current VCC5 (disabled) ICC5 dis UGATE, LGATE and LDO_DR open; FS_DIS = GND (Note 4) 5 7.5 mA Nominal Supply Current VCC12 (includes PVCC5 current) ICC12 UGATE, LGATE and LDO_DR open; FOSC = 620kHz 12 18 mA Nominal Supply Current VCC5 ICC5 UGATE, LGATE and LDO_DR open; FOSC = 620kHz 4 6 mA Maximum PVCC5 Current Available (Note 5) VCC12 to PVCC5 Current Limit (Note 5) PVCC5 Voltage IPVCC5 100 mA IPVCC5CL 150 mA VPVCC5 ISL6549C; No external load 4.95 5.25 5.8 V ISL6549I; No external load 4.85 5.25 5.8 Rising VCC5 Threshold VCC12 = 12V 3.7 4.2 4.5 V Falling VCC5 Threshold VCC12 = 12V 3.3 3.8 4.1 V Rising VCC12 Threshold VCC5 = 5V 8.8 9.5 10.0 V Falling VCC12 Threshold VCC5 = 5V 7.0 7.5 8.0 V ISL6549C; RFS_DIS = 45.3k 540 620 700 kHz ISL6549I; RFS_DIS = 45.3k 525 620 700 kHz POWER-ON RESET OSCILLATOR AND SOFT-START Switching Frequency FN9168 Rev 2.00 September 22, 2006 FOSC Page 4 of 18 ISL6549 Electrical Specifications Recommended Operating Conditions, unless otherwise noted. VCC12 = 12V Temperature = 0 to +70°C (typical = +25°C) for Commercial; Temperature = -40 to + 85°C (typical = +25°C) for Industrial. Refer to Block Diagram, Simplified Power System Diagram, and Typical Application Schematic. (Continued) PARAMETER SYMBOL Sawtooth Amplitude (Note 6) TEST CONDITIONS MIN DVOSC Soft-Start Interval TSS FOSC = 620kHz TYP MAX UNITS 1.5 V 6.8 ms REFERENCE VOLTAGE Reference Voltage VREF ISL6549C; For Error Amp 1 and 2 0.792 0.8 0.808 V ISL6549I; For Error Amp 1 and 2 0.788 0.8 0.812 V PWM CONTROLLER ERROR AMPLIFIER DC Gain (Note 6) RL = 10K, CL = 10pF 96 dB GBWP RL = 10K, CL = 10pF 20 MHz Slew Rate (Note 6) SR RL = 10K, CL = 10pF 8 V/µs FB Input Current II  VFB = 0.8V Gain-Bandwidth Product (Note 6) 0.1 1.0 µA COMP High Output Voltage VOUT High 4.8 V COMP Low Output Voltage VOUT Low 0.6 V COMP High Output, Source Current IOUT High -2.8 mA Undervoltage Level (VFB/VREF) VUV 70 75 80 % 17 17.5 18 5.25 6 V 0 0.5 V PWM CONTROLLER GATE DRIVERS UGATE Maximum Voltage VHUGATE VCC12 = 12V; PHASE = 12V LGATE Maximum Voltage VHLGATE VCC12 = 12V; based on PVCC5 voltage UGATE and LGATE Minimum Voltage VLGATE VCC12 = 12V; PHASE = 0V UGATE Source Output Impedance RDS(ON) VCC12 = 12V; IGATE = 100mA 0.8  UGATE Sink Output Impedance RDS(ON) VCC12 = 12V; IGATE = 100mA 0.7  LGATE Source Output Impedance RDS(ON) VCC12 = 12V; IGATE = 100mA 0.8  LGATE Sink Output Impedance RDS(ON) VCC12 = 12V; IGATE = 100mA 0.4  Gain RL = 10K, CL = 10pF 100 dB GBWP RL = 10K, CL = 10pF 2 MHz Slew Rate (Note 6) SR RL = 10K, CL = 10pF 6 Vµs LDO_FB Input Current II  VLDO_FB = 0.8V 0.1 1.0 µA VCC12 = 12V 11.0 11.5 V 0.0 0.5 V LINEAR REGULATOR (LDO_DR) DC Gain (Note 6) Gain-Bandwidth Product (Note 6) LDO_DR High Output Voltage VOUT High LDO_DR Low Output Voltage VOUT Low LDO_DR High Output Source Current IOUT High LDO_DR Low Output Sink Current IOUT Low Undervoltage Level (VLDO_FB/VREF) VUV VOUT = 2.0V Percent of Nominal 70 2.0 mA 0.5 mA 75 80 % NOTES: 4. Current in VCC5 is actually higher disabled, due to extra current required to pull down against the FS_DIS pin. VCC12 current is lower disabled. 5. Guaranteed by design, not production tested. Exceeding the maximum current from PVCC5 may result in degraded performance and unsafe operation. 6. Guaranteed by design, not production tested. FN9168 Rev 2.00 September 22, 2006 Page 5 of 18 ISL6549 Functional Pin Description VCC12 This is the power supply pin for the IC; it sources the internal 5V regulator used for the gate drivers. Provide a local decoupling capacitor to GND. The voltage at this pin is monitored for Power-On Reset (POR) purposes. The 16 Ld QFN and 16 Ld QSOP have two VCC12 pins; tie them together on the board. VCC5 This pin supplies the internal 5V bias for analog and logic functions. Provide a local decoupling capacitor to GND, and a resistor to PVCC. The voltage at this pin is monitored for Power-On Reset (POR) purposes. See “Internal PVCC5 Regulator” on page 7 for more details. GND, AGND, DGND These pins are the signal ground for the IC. All voltage levels are measured with respect to these pins. Connect all to the ground plane via the shortest available path. PVCC5 This pin is the internal 5V linear regulator for the BOOT supply (for the UGATE driver), and the source for the LGATE. Provide a local decoupling capacitor to PGND. Do not use this pin as a voltage source for other circuits. See “Internal PVCC5 Regulator” on page 7 for more details. PGND This pin is the power ground return for the lower gate driver. (LGATE). Connect to the ground plane on the board via the shortest available path. UGATE This output pin drives the upper MOSFET gate from the internal 5V regulator. Connect it to the gate of the upper MOSFET via a short, low inductance trace. BOOT The BOOT pin, along with the external capacitor (from PHASE to BOOT), an internal diode, and the internal 5.5V regulator, creates the bootstrap voltage for the upper gate driver (UGATE). The maximum voltage is around 5.5V (above PHASE). FB FB is the available external inverting input pin of the error amplifier. Connect the output of the switching regulator to this pin through a properly sized resistor divider, to set the output voltage. The voltage at this pin is regulated to the internal reference voltage. This pin is also monitored for undervoltage detection. COMP COMP is the available external output pin of the error amplifier. This pin is used to compensate the voltage-mode control feedback loop of the standard synchronous rectified buck converter. Connect an appropriate compensation network between this and the FB pin. See “PWM Controller Feedback Compensation” on page 10 for more information. FS_DIS This input pin has two functions. A resistor to GND sets the internal oscillator frequency for the switching regulator. In addition, if the pin is pulled down towards GND with a low impedance ( 9.5V VCC12 (2V/DIV) VCC5 (2V/DIV) VOUT1 (1V/DIV) VOUT2 (1V/DIV) GND> FIGURE 1. 12V POWER-UP INTO SOFT-START Figure 2 shows more detail of the output ramps, by increasing the time and voltage resolution. The clock for the DAC producing the steps is approximately 9.4kHz (600kHz/64), so each step is just over 100µs long. The step voltage is 1/64 of the final value for each output; around 31mV for VOUT1 and 15.6mV for VOUT2 in this example. By providing many small steps of voltage (and current) that effectively charge the output capacitor, the potentially large peak current resulting from a sudden, uncontrolled voltage rise are eliminated, by spreading it out over the whole ramp time. Page 7 of 18 ISL6549 Undervoltage Protection . VOUT1 VOUT2 The FB and LDO_FB pins are each monitored during converter operation by their own Undervoltage (UV) comparator. If either FB voltage drops below 75% of the reference voltage (75% of 0.8V = 0.6V), a fault signal is internally generated, and the fault logic shuts down BOTH regulators. The UV comparators are enabled when the soft-start ramp is about one-quarter (25%) done. (0.5V/DIV) VOUT2 (2.5V) GND> VOUT1 (1.5V) FIGURE 2. EXPANDED VIEW: VOLTAGE RAMP AND TIME A few clock cycles are used for initialization to insure that softstart begins near zero volts. The ramps are the same, whether triggered by releasing FS_DIS or by exceeding the POR trip levels. GND> DELAY INTERVAL Both outputs use the same soft-start ramp, and the ramp time is determined by the switching frequency. Thus, there is no simple way to disable or sequence them independently, or to change the ramp rate independently of the clock. If the switcher output is already pre-charged to a voltage when the regulator starts up, the ISL6549 will detect this condition (see Figure 3). The red trace shows the normal ramp, when the output starts at GND. The green trace shows the case when the output is pre-charged to a voltage less than the final output. The upper or lower FET does not turn on until the softstart ramp voltage exceeds the output; then the output starts ramping seamlessly from there. If the output voltage is precharged above the normal output level, as shown in the magenta trace, neither FET will turn on until the end of the soft-start ramp; then the output will be quickly pulled down to the final value. VCC12 > 9.5V VCC12 (2V/DIV) VOUT2 OVER-CHARGED (1V/DIV) VOUT2 PRE-CHARGED (1V/DIV) GND> VOUT2 NO CHARGE (1V/DIV) FIGURE 3. PRE-CHARGED OUTPUT FN9168 Rev 2.00 September 22, 2006 INTERNAL SOFT-START FUNCTION GND> SOFT-START DELAY SOFT-START DELAY T1 T2 T0 (T1 TO T2 NOT TO SCALE) TIME T3 T4 FIGURE 4. UNDERVOLTAGE PROTECTION RESPONSE Figure 4 illustrates the protection feature responding to a UV event on VOUT1. At time T0, VOUT1 has dropped below 75% of the nominal output voltage. Both outputs are quickly shut down and the UGATE and LGATE stop switching immediately, but the fall time of each output is determined by the load and/or short condition on each plus the output capacitance that needs to be discharged. The soft-start function begins producing an internal soft-start ramp. The delay interval, T0 to T1, seen by the output is equivalent to one soft-start cycle. Then a normal soft-start ramp of the output starts, at time T1. At the one-quarter point of the soft-start ramp (not drawn exactly to scale), the good output will have ramped onequarter way up, while the shorted output will presumably be lower than a quarter (depending on the magnitude of the short). Once the UV comparators are enabled (at the one-quarter point) both outputs will again shut down (if the fault is still present on one of them). Time T2 starts a new internal soft-start cycle, and at T3, starts a new ramp, similar to T1. This time, if we assume the short has gone away, the outputs will ramp up to T4 as they should. If the short has not gone away, then the T0, T1, T2 hiccup mode cycle will keep repeating indefinitely; this cycle time is the equivalent of 1.25 Page 8 of 18 ISL6549 soft-start cycles (1 internal soft-start ramp cycle, plus one-quarter on the next). dependence between the resistor chosen and the resulting switching frequency. If either VINx voltage is not present at startup, that will cause a UV shutdown and restart cycle; similarly, if either VINx is removed after start-up, a shutdown and restart cycle will start when its output drifts down to the UV trip point. But in both cases, once the VINx is restored, the VOUTs will recover on the next soft-start ramp. Output Voltage Selection 1.6ms VOUT2 (0.5V/DIV) 6.4ms The output voltage of the PWM converter can be programmed to any level between VIN1 and the internal reference, 0.8V. However, even though the ISL6549 can run at near 100% duty cycle at zero load, additional voltage margin is required above VIN1 to allow for loading. An external resistor divider is used to scale the output voltage relative to the reference voltage and feed it back to the inverting input of the error amplifier (see Figure 7). A typical value for R1 may be 1.00k (±1% for accuracy), and then R4 (also ±1%) is chosen according to Equation 1: R1  0.8V R4 = ---------------------------------------V OUT1 – 0.8V VOUT2 (0.5V/DIV) GND> VOUT1 (0.5V/DIV) FIGURE 5. UNDERVOLTAGE PROTECTION (SIMULATED BY HAVING NO VIN1 ON POWER-UP) Figure 5 shows an example of the start-up, with VIN1 not powered. VOUT2 ramps up one-quarter of the way, at which time the UV comparators are enabled. Since VIN1 is not present, VOUT1 will not be following the soft-start ramp up, and it will fail the test for UV, shutting down both outputs. It starts an internal delay time-out (equal to one soft-start interval), and then starts a new ramp. For this example, it shows about a 1.6ms ramp up, and 6.4ms off, before the next ramp starts. Thus, the total period of 8ms is based on 1.25 soft-start cycles (one-quarter of the first ramp, and then one full time-out, at a clock period of around 1.6µs) The dotted magenta line shows the case where VOUT2 is allowed to ramp all of the way up to 2V. R1 is also part of the compensation circuit (see “PWM Controller Feedback Compensation” on page 10 for more details), so once chosen for that, it should not be changed to adjust VOUT1; only change R4. If the output voltage desired is 0.8V, simply route VOUT1 back to the FB pin through R1, but do not populate R4. VOUT1 voltages less than the 0.8V reference are not available. VIN1 CIN1 LOUT VOUT1 COUT1 + ISL6549 Q1 UGATE PHASE + LGATE Q2 FB R3 R1 C2 COMP C3 R2 R4 Switching Frequency 1M (EQ. 1) C1 R1 V OUT1 = 0.8   1 + -------- R4 FREQUENCY (kHz) FIGURE 7. OUTPUT VOLTAGE SELECTION OF THE SWITCHER (VOUT1) 100k 10k 100k R (k) 1M FIGURE 6. FREQUENCY vs FS RESISTOR The switching frequency of the ISL6549 is determined by the value of the FS resistor. The graph in Figure 6 shows the FN9168 Rev 2.00 September 22, 2006 The linear regulator output voltage is also set by means of an external resistor divider as shown in Figure 8. Select a value for R5 (typical 1.00k ±1% for accuracy), and use Equation 2 to calculate R6 (also ±1%), where VOUT2 is the desired linear regulator output voltage and VREF is the internal reference voltage, 0.8V. For an output voltage of 0.8V, simply populate R5 with a value less than 5k and do not populate R6. VOUT2 voltages less than the 0.8V reference are not available. R 5  0.8V R 6 = --------------------------------------V OUT 2 – 0.8V (EQ. 2) Page 9 of 18 ISL6549 For most situations, no external compensation is required for the linear output. See “Linear Controller Feedback Compensation” on page 12. For both outputs, the selection of 1% resistors may not be able to get the exact ratio desired for any given output voltage. If the output must be defined better, then one option is to place a much bigger resistor in parallel with R4 or R6, to lower its value. For example, a 100k in parallel with a 1.00k yields 990, 1% below 1.00k, which gives finer resolution than the next lower size (976 1%). The big resistor may not have to be 1% tolerance either. If the linear output is not required, connect the LDO_DR pin directly to LDO_FB pin with no other components. This will terminate the signals and keep the linear from tripping its undervoltage, which would force both outputs into retry. VIN2 CIN2 and forces the LGATE to go high for one oscillator cycle, which allows the bootstrap capacitor time to recharge. PWM Controller Feedback Compensation This section highlights the design consideration for a voltage-mode controller requiring external compensation. To address a broad range of applications, a type-3 feedback network is recommended (see Figure 9). C2 R2 C1 COMP FB C3 ISL6549 R1 R3 + Q3 VDIFF (VOUT) LDO_DR FIGURE 9. COMPENSATION CONFIGURATION FOR ISL6549 CIRCUIT VOUT2 LDO_FB COUT2 R5 + R6 ISL6549 R5 V OUT2 = 0.8   1 + --------  R6 FIGURE 8. OUTPUT VOLTAGE SELECTION OF THE LINEAR (VOUT2) Converter Shutdown Figure 10 highlights the voltage-mode control loop for a synchronous-rectified buck converter, applicable to the ISL6549 circuit. The output voltage (VOUT) is regulated to the reference voltage, VREF. The error amplifier output (COMP pin voltage) is compared with the oscillator (OSC) modified saw-tooth wave to provide a pulse-width modulated wave with an amplitude of VIN at the PHASE node. The PWM wave is smoothed by the output filter (L and C). The output filter capacitor bank’s equivalent series resistance is represented by the series resistor E. Pulling and holding the FS_DIS pin near GND will shut down both regulators; almost any NFET or other pull-down device (100µF) and so is its ESR (>20mW), then it should be stable for loads as low as 10mA up to at least 4A. If smaller values of capacitance and/or ESR are desired, then special considerations may be required to add external compensation (as shown in Figure 8). An output capacitor is required to filter the output and supply the load transient current. The filtering requirements are a function of the switching frequency and the ripple current. The load transient requirements are a function of the slew rate (di/dt) and the magnitude of the transient load current. These requirements are generally met with a mix of capacitors and careful layout. Component Selection Guidelines Modern microprocessors produce transient load rates above 1A/ns. High frequency capacitors initially supply the transient and slow the current load rate seen by the bulk capacitors. The bulk filter capacitor values are generally determined by the ESR (effective series resistance) and voltage rating requirements rather than actual capacitance requirements. Output Inductor Selection The output inductor is selected to meet the output voltage ripple requirements and minimize the converter’s response time to the load transient. The inductor value determines the converter’s ripple current and the ripple voltage is a function of the ripple current. The ripple voltage and current are approximated by Equation 10. V IN - V OUT V OUT I = --------------------------------  ---------------F SW x L V IN VOUT = I x ESR (EQ. 10) Increasing the value of inductance reduces the ripple current and voltage. However, the large inductance values reduce the converter’s response time to a load transient (and usually increases the DCR of the inductor, which decreases the efficiency). Increasing the switching frequency (FSW) for a given inductor also reduces the ripple current and voltage. FN9168 Rev 2.00 September 22, 2006 High frequency decoupling capacitors should be placed as close to the power pins of the load as physically possible. Be careful not to add inductance in the circuit board wiring that could cancel the usefulness of these low inductance components. Consult with the manufacturer of the load on specific decoupling requirements. And keep in mind that not all applications have the same requirements; some may need many ceramic capacitors in parallel; others may need only one. Use only specialized low-ESR capacitors intended for switching-regulator applications for the bulk capacitors. The bulk capacitor’s ESR will determine the output ripple voltage and the initial voltage drop after a high slew-rate Page 12 of 18 ISL6549 transient. An aluminum electrolytic capacitor's ESR value is related to the case size with lower ESR available in larger case sizes. However, the equivalent series inductance (ESL) of these capacitors increases with case size and can reduce the usefulness of the capacitor to high slew-rate transient loading. Unfortunately, ESL is not always a specified parameter. Work with your capacitor supplier and measure the capacitor’s impedance with frequency to select a suitable component. In most cases, multiple electrolytic capacitors of small case size perform better than a single large case capacitor. Input Capacitor Selection Use a mix of input bypass capacitors to control the voltage overshoot across the MOSFETs. Use small ceramic capacitors for high frequency decoupling and bulk capacitors to supply the current needed each time Q1 turns on. Place the small ceramic capacitors physically close to the MOSFETs and between the drain of upper FET Q1 and the source of lower FET Q2. The important parameters for the bulk input capacitor are the voltage rating and the RMS current rating. For reliable operation, select the bulk capacitor with voltage and current ratings above the maximum input voltage and largest RMS current required by the circuit. The capacitor voltage rating should be at least 1.25 times greater than the maximum input voltage and a voltage rating of 1.5 times is a conservative guideline. The RMS current rating requirement for the input capacitor of a buck regulator is approximately half the DC load current. Several electrolytic capacitors may be needed. Bootstrap Capacitor Selection The boot diode is internal to the ISL6549, and uses PVCC5 to charge the external boot capacitor. The size of the bootstrap capacitor can be chosen by using the equations in Equation 12. Q GATE C BOOT  -------------------V and N  Q G  V IN Q GATE = --------------------------------V GS where N is the number of upper FETs QG is the total gate charge per upper FET VIN is the input voltage VGS is the gate-source voltage (~5V for ISL6549) V is the change in boot voltage before and immediately after the transfer of charge; typically 0.7V to 1.0V Q GATE N  Q G  V IN 1  33  12 C BOOT  -------------------- = ---------------------------------- = ---------------------------- = 0.113F V 5  0.7 V GS  V (EQ. 12) The last equation plugs in some typical values: N = 1; QG is 33nC, VIN is 12V, VGS is 11V, Vmax = 1V. In this example, CBOOT  0.113µF. This value is often rounded to FN9168 Rev 2.00 September 22, 2006 0.1µF or 0.22µF as a starting value. The bootstrap capacitors for the ISL6549 can usually be rated for 6.3V. Switcher FET Considerations The IC was designed for nominal 12V supply for VIN1 (drain of upper FET Q1). However, it will work with most any voltage (from other supplies or other regulator outputs) down to around 1V, as long as the input is above the output by a sufficient margin (based on practical duty cycle limitations and upper FET RDS(ON) constraints). For example, although the IC can function at near 100% duty cycle, the voltage drop due to the RDS(ON) of the upper FET at full load current will limit the practical duty cycle to something less than 100%. So the VIN1 range is roughly 1.0V up to 12V, with the VOUT1 range slightly below it. Therefore, the FETs need to be rated for drain-source breakdown above the VIN1 voltage; 20V and 30V ratings are common. The ISL6549 gate drivers (UGATE and LGATE) were designed to drive up to 2 upper and 2 lower 8 Ld SOIC FETs; when the FETs are properly sized, the output currents can range from under 1A to over 20A. Driving more or bigger FETs is not recommended; even if there is enough current (from the internal PVCC5 regulator), the gate driver waveforms may be degraded. DPAK FET packages can be used, but D2PAK FETs are not recommended, due to the higher inductance of the package leads. For example, the inductance in the source of the lower FET can create large negative spikes on the PHASE node when the UGATE turns off. Both the UGATE and LGATE voltages are derived from the internal PVCC5 internal regulator, typically 5.25V. UGATE is only about 5.0V above PHASE, due to the drop in the internal BOOT diode charging the BOOT capacitor; LGATE sees the full 5.25V. So both are considered “5V” drivers; this affects the FET selection in two ways. First, the FET gate-source voltage rating can be as low as 12V (this rating is usually consistent with the 20V or 30V breakdown chosen above). Second, the FETs must have a low threshold voltage (around 1V), in order to have its RDS(ON) rating at VGS = 4.5V in the 10m-20m range. While some FETs are also rated with gate voltages as low as 2.7V, with typical thresholds under 1V, these can cause application problems. As LGATE shuts off the lower FET, it does not take much ringing in the LGATE signal to turn the lower FET back on, while the Upper FET is also turning on, causing some shoot-through current. So avoid FETs with thresholds below 1V. Another set of important parameters are the turn-on and turn-off times (internal propagation delays, how long before the output starts to switch) and the rise and fall times (external delay to complete the switching). The UGATE and LGATE drivers use an adaptive technique to determine the dead time (when both gate drivers signals are low). Comparators sense when each driver is getting close to GND (such that its FET is close to being off), before turning on the other. This technique minimizes the dead time to the 10ns-20ns range. So if either Page 13 of 18 ISL6549 FET is particularly slow in these parameters, there is a greater chance that shoot-through current will occur. As referenced in the “Block Diagram” on page 2, the UGATE signal is referenced to PHASE signal. The deadtime comparator also looks at the difference (UGATE - PHASE). This is significant when viewing the gate driver waveforms on an oscilloscope. One simple indication of shoot-through (or insufficient deadtime) is when the UGATE and LGATE signals overlap. But in this case, one should look at UGATE-PHASE (either by a math function of the two signals, or by using a differential probe measurement) compared to LGATE. Figure 12 shows an example of this. It looks as if the UGATE and LGATE signals have crossed, but the UGATE-PHASE signal does not cross the LGATE. typically adds power to the IC side, but may reduce some power on the FET side). For low duty cycle applications (such as 12V in to 1.5V out), the upper FET is usually chosen for low gate charge, since switching losses are key, while the lower FET is chosen for low RDS(ON), since it is on most of the time. For high duty cycles (such as 3.3V in to 2.5V out), the opposite is true. In summary, the following parameters may need to be considered in choosing the right FETs for an application: drain-source breakdown voltage rating, gate-source rating, maximum current, thermal and package considerations, low gate threshold voltage, gate charge, RDS(ON) at 4.5V, and switching speed. And, of course, the board layout constraints and cost also are factored into the decision. Linear FET Considerations UGATE (4V/DIV) PHASE (4V/DIV) UGATE-PHASE (4V/DIV) LGATE (4V/DIV) GND> FIGURE 12. GATE DRIVER WAVEFORMS One important consideration is negative spikes on the PHASE node as it goes low. The upper FET is turning off, but before the lower FET can take over, stray inductance in the layout (on the board, or even the inductance of some components, such as D2PAK FETs) can contribute to the PHASE going negative. There is no maximum spec for PHASE spike below GND, however, there is an absolute maximum rating for (BOOT - PHASE) of 7V; exceeding this limit can cause damage to the IC, and possibly to the system. Since the BOOT signal is typically 5V above the PHASE node most of the time, it only takes a few volts of a spike on either signal to exceed the limit. A good design should be characterized by using the math function or differential probe, and monitoring these signals for compliance, especially during full loads, where the signals are usually the noisiest. Slowing down the turn-off of the upper FET may help, while at other times, sometimes the problem may just be the choice of FETs. If the power efficiency of the system is important, then other FET parameters are also considered. Efficiency is a measure of power losses from input to output, and it contains two major components: losses in the IC (mostly in the gate drivers) and losses in the FETs. Optimizing the sum involves many trade-offs (for example, raising the voltage of the gate drivers FN9168 Rev 2.00 September 22, 2006 The linear FET is chosen primarily for thermal performance. The current for the linear output is generally limited by the power dissipation (P = (VIN2 - VOUT2) * I), and the FET thermal rating for getting the heat out of the package, and spreading it out on the board, especially when no heatsinks or airflow is available. It is generally not recommended to parallel two FETs in order to get higher current or to spread out the heat, as the FETs would need to be very well-matched in order to share the current properly. Should this approach be desired, and as perfectly matched FETs are seldom available, a small resistor, or PCB trace of suitable resistance placed in the source of each of the FETs can be used to improve the current balance. The maximum VOUT2 voltage allowed is determined by several factors: • Power dissipation, as described earlier • Input voltage available • LDO_DR voltage • FET chosen The voltage cannot be any higher than the input voltage available, and the max VIN2 is 12V (13.2V for a ±10% supply). The LDO_DR voltage is driven from the VCC12 rail; allowing for headroom, the typical maximum voltage is 11V (lower as VCC12 goes to its minimum of 10.8V). So the maximum output voltage will be at least a VGS drop (which includes the FET threshold voltage) below the 11V, at the maximum load current; some additional headroom is usually needed to handle transient conditions. So a practical typical value around 8V may be possible, but remember to also factor in the variations for worst case conditions on VIN2 and the FET parameters. As long as the VIN2 is low enough such that headroom versus VCC12 is not a problem, then the maximum output voltage is just below VIN2, based on the RDS(ON) drop at maximum current. The input supply for VIN2 can also be any available supply less than 12V, subject to the considerations above. The drain-source breakdown voltage of the FET should be greater Page 14 of 18 ISL6549 Application Guidelines Layout Considerations Layout is very important in high frequency switching converter design. With power devices switching efficiently at 600kHz, the resulting current transitions from one device to another cause voltage spikes across the interconnecting impedances and parasitic circuit elements. These voltage spikes can degrade efficiency, radiate noise into the circuit, and lead to device overvoltage stress. Careful component layout and printed circuit board design minimizes the voltage spikes in the converters. As an example, consider the turn-off transition of the PWM upper MOSFET. Prior to turn-off, the MOSFET is carrying the full load current. During turn-off, current stops flowing in the upper MOSFET and is picked up by the lower MOSFET and parasitic diode. Any parasitic inductance in the switched current path generates a large voltage spike during the switching interval. Careful component selection, tight layout of the critical components, and short, wide traces minimizes the magnitude of voltage spikes. There are two sets of critical components in a DC/DC converter using the ISL6549. The switching components are the most critical because they switch large amounts of energy, and therefore tend to generate large amounts of noise. Next are the small signal components which connect to sensitive nodes or supply critical bypass current and signal coupling. The critical small signal components include any bypass capacitors, feedback components, and compensation FN9168 Rev 2.00 September 22, 2006 Then the switching components should be placed close to the ISL6549. Minimize the length of the connections between the input capacitors, CIN, and the power switches by placing them nearby. Position both the ceramic and bulk input capacitors as close to the upper MOSFET drain as possible, and make the GND returns (from lower FET source to VIN cap GND) short. Position the output inductor and output capacitors between the upper MOSFET and lower MOSFET and the load. VIN1 VCC12 VCC12 C4 PVCC5 GND CIN1 ISL6549 PVCC5 C6 BOOT PGND C7 Q1 UGATE R12 PHASE VCC5 LGATE COMP VCC5 C5 Q2 C2 VOUT1 COUT1 C1 R2 GND LOUT R1 FB C3 R3 R4 VIN2 FS_DIS R7 Q3 LDO_DR CIN2 R5 VOUT2 LDO_FB R6 COUT2 LOAD A multilayer printed circuit board is recommended. Figure 13 shows the connections of the critical components in the converter. Capacitors CIN and COUT could each represent numerous physical capacitors. Dedicate one solid layer, usually a middle layer of the PC board, for a ground plane and make all critical component ground connections through vias to this layer. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Keep the metal runs from the PHASE terminal to the output inductor short. The power plane should support the input and output power nodes. Use copper filled polygons on the top and bottom circuit layers for the phase node. Use the remaining printed circuit layers for small signal wiring. The wiring traces from the LGATE and UGATE pins to the MOSFET gates should be kept short and wide enough to easily handle the several Amps of drive current. components. Position the bypass capacitors, C4, C5, and C6 close to their pins with a local GND connection, or via directly to the ground plane. R12 should be placed near VCC5 and PVCC5 pins. FS_DIS resistor R7 should be near the FS-DIS pin, and its GND return should be short, and kept away from the noisy FET GND. Place the PWM converter compensation components close to the FB and COMP pins. The feedback resistors for both regulators should also be located as close as possible to the relevant FB pin with vias tied straight to the ground plane as required. LOAD than the VIN2 voltage. The FET’s gate-source rating should be greater than 12V (even though the output voltage may not require such a high gate voltage, load transients or other disturbances might force LDO_DR to momentarily approach 12V). The FET threshold is not critical, except for the cases where the LDO_DR headroom is diminished. And finally, the package (and board area allowed) must be able to handle the maximum power dissipation expected. KEY ISLAND ON POWER PLANE LAYER ISLAND ON CIRCUIT PLANE LAYER VIA CONNECTION TO GROUND PLANE FIGURE 13. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS References Applications Note: AN1201 Visit us on the internet: www.intersil.com Page 15 of 18 ISL6549 Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L16.4x4 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220-VGGC ISSUE C) MILLIMETERS SYMBOL MIN NOMINAL MAX NOTES A 0.80 0.90 1.00 - A1 - - 0.05 - A2 - - 1.00 A3 b 0.23 D 0.28 9 0.35 5, 8 4.00 BSC D1 D2 9 0.20 REF - 3.75 BSC 1.95 2.10 9 2.25 7, 8 E 4.00 BSC - E1 3.75 BSC 9 E2 1.95 e 2.10 2.25 7, 8 0.65 BSC - k 0.25 - - - L 0.50 0.60 0.75 8 L1 - - 0.15 10 N 16 2 Nd 4 3 Ne 4 3 P - - 0.60 9  - - 12 9 Rev. 5 5/04 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P &  are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. FN9168 Rev 2.00 September 22, 2006 Page 16 of 18 ISL6549 Small Outline Plastic Packages (SOIC) M14.15 (JEDEC MS-012-AB ISSUE C) N INDEX AREA H 0.25(0.010) M 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M  C A M SYMBOL MIN MAX MIN A 0.0532 0.0688 1.35 A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3367 0.3444 8.55 8.75 3 E 0.1497 0.1574 3.80 4.00 4 e C 0.10(0.004) B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. MILLIMETERS 0.050 BSC MAX 1.75 1.27 BSC NOTES - - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N  14 0o 14 8o 0o 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. FN9168 Rev 2.00 September 22, 2006 Page 17 of 18 ISL6549 Shrink Small Outline Plastic Packages (SSOP) Quarter Size Outline Plastic Packages (QSOP) M16.15A N INDEX AREA H 0.25(0.010) M E 2 INCHES GAUGE PLANE -B1 16 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE (0.150” WIDE BODY) B M 3 0.25 0.010 SEATING PLANE -A- A D h x 45° -C- e 0.17(0.007) M  A2 A1 B L C 0.10(0.004) B S C A M MILLIMETERS SYMBOL MIN MAX A 0.061 0.068 1.55 MIN 1.73 MAX NOTES - A1 0.004 0.0098 0.102 0.249 - A2 0.055 0.061 1.40 1.55 - B 0.008 0.012 0.20 0.31 9 C 0.0075 0.0098 0.191 0.249 - D 0.189 0.196 4.80 4.98 3 E 0.150 0.157 3.81 3.99 4 e 0.025 BSC 0.635 BSC - H 0.230 0.244 5.84 6.20 - h 0.010 0.016 0.25 0.41 5 L 0.016 0.035 0.41 0.89 6 NOTES: N 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95.  16 0° 16 8° 0° 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 7 8° Rev. 2 6/04 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “B” does not include dambar protrusion. Allowable dambar protrusion shall be 0.10mm (0.004 inch) total in excess of “B” dimension at maximum material condition. 10. Controlling dimension: INCHES. Converted millimeter dimensions are not necessarily exact. © Copyright Intersil Americas LLC 2004-2006. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9168 Rev 2.00 September 22, 2006 Page 18 of 18
ISL6549CBZR5213 价格&库存

很抱歉,暂时无法提供与“ISL6549CBZR5213”相匹配的价格&库存,您可以联系我们找货

免费人工找货