X4005M8-4.5A

X4003, X4005 CPU Supervisor DATASHEET SIGNS N E W DE R O F D T N DE ACEM EN COMME ED REPL Center at N OT R E D N E M OM u p p o rt NO R E C chnical S .intersil.com/tsc e T r u o t contac ERSIL or www T 1-888-IN These devices combine three popular functions; Power-on Reset Control, Watchdog Timer and Supply Voltage Supervision. This combination lowers system cost, reduces board space requirements and increases reliability. FN8113 Rev 2.00 June 30, 2008 Features • Selectable watchdog timer - Select 200ms, 600ms, 1.4s, off • Low VCC detection and reset assertion - Five standard reset threshold voltages nominal 4.62V, 4.38V, 2.92V, 2.68V, 1.75V - Adjust low VCC reset threshold voltage using special programming sequence - Reset signal valid to VCC = 1V Applying power to the device activates the power-on reset circuit which holds RESET/RESET active for a period of time. This allows the power supply and oscillator to stabilize before the processor can execute code. The Watchdog Timer provides an independent protection mechanism for microcontrollers. When the microcontroller fails to restart a timer within a selectable time out interval, the device activates the RESET/RESET signal. The user selects the interval from three preset values. Once selected, the interval does not change, even after cycling the power. • Low power CMOS - 12µA typical standby current, watchdog on - 800nA typical standby current watchdog off - 3mA active current • 400kHz I2C interface The device’s low VCC detection circuitry protects the user’s system from low voltage conditions, resetting the system when VCC falls below the minimum VCC trip point. RESET/RESET is asserted until VCC returns to proper operating level and stabilizes. Five industry standard VTRIP thresholds are available; however, Intersil’s unique circuits allow the threshold to be reprogrammed to meet custom requirements, or to fine-tune the threshold for applications requiring higher precision. • 1.8V to 5.5V power supply operation • Available packages - 8 Ld SOIC - 8 Ld MSOP • Pb-free available (RoHS compliant) Pinout X4003, X4005 (8 LD SOIC, MSOP) TOP VIEW NC 1 8 VCC NC 2 7 RESET/RESET* VSS 3 6 WP SCL 4 5 SDA *RESET APPLIES TO X4003 RESET APPLIES TO X4005 Block Diagram WATCHDOG TRANSITION DETECTOR WATCHDOG TIMER RESET WP SDA SCL RESET (X4003) DATA REGISTER COMMAND DECODE AND CONTROL LOGIC RESET AND WATCHDOG TIMEBASE VCC THRESHOLD RESET LOGIC VCC + VTRIP FN8113 Rev 2.00 June 30, 2008 RESET (X4005) CONTROL REGISTER - POWER-ON AND LOW VOLTAGE RESET GENERATION Page 1 of 16 X4003, X4005 Ordering Information PART NUMBER RESET (ACTIVE LOW) PART MARKING PART NUMBER RESET (ACTIVE HIGH) PART VCC RANGE VTRIP RANGE TEMP. RANGE MARKING (V) (V) (°C) X4003M8-4.5A ACH X4005M8-4.5A ACQ X4003M8Z-4.5A (Note) DAH X4005M8Z-4.5A (Note) X4003S8-4.5A X4003 AL X4005S8-4.5A X4003S8Z-4.5A (Note) 4.5 to 4.75 PKG. DWG. # 0 to +70 8 Ld MSOP (3.0mm) DAP 0 to +70 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4005 AL 0 to +70 8 Ld SOIC (150 mil) X4003 ZAL X4005S8Z-4.5A (Note) X4005 ZAL 0 to +70 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8I-4.5A ACI X4005M8I-4.5A ACR -40 to +85 8 Ld MSOP (3.0mm) X4003M8IZ-4.5A (Note) DAD X4005M8IZ-4.5A DAM (Note) -40 to +85 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4003S8I-4.5A X4003 AM X4005S8I-4.5A -40 to +85 8 Ld SOIC (150 mil) X4003S8IZ-4.5A (Note) X4003 ZAM X4005S8IZ-4.5A X4005 ZAM (Note) -40 to +85 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8 ACJ X4005M8 4.5 to 5.5 PACKAGE X4005 AM ACS 4.25 to 4.5 0 to +70 8 Ld MSOP (3.0mm) M8.118 MDP0027 M8.118 MDP0027 M8.118 X4003M8Z (Note) DAE X4005M8Z (Note) DER 0 to +70 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4003S8 X4005S8 0 to +70 8 Ld SOIC (150 mil) 0 to +70 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003 X4005 MDP0027 X4003S8Z (Note) X4003 Z X4005S8Z (Note) X4005 Z X4003M8I X4005M8I ACT -40 to +85 8 Ld MSOP (3.0mm) X4003M8IZ (Note) DAA X4005M8IZ (Note) DAJ -40 to +85 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4003S8I X4005S8I X4005 I -40 to +85 8 Ld SOIC (150 mil) X4003S8IZ (Note) X4003 ZI X4005S8IZ (Note) X4005 ZI -40 to +85 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8-2.7A ACL X4005M8-2.7A ACU X4003M8Z-2.7A (Note) DAG X4005M8Z-2.7A (Note) X4003S8-2.7A X4003 AN X4005S8-2.7A X4003S8Z-2.7A (Note) ACK X4003 I 2.85 to 3.0 MDP0027 0 to +70 8 Ld MSOP (3.0mm) DAO 0 to +70 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4005 AN 0 to +70 8 Ld SOIC (150 mil) X4003 ZAN X4005S8Z-2.7A (Note) X4005 ZAN 0 to +70 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8-2.7 ACN X4005M8-2.7 ACW 0 to +70 8 Ld MSOP (3.0mm) X4003M8Z-2.7 (Note) DAF X4005M8Z-2.7 (Note) DAN 0 to +70 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4003S8-2.7 X4003 F X4005S8-2.7 X4005 F 0 to +70 8 Ld SOIC (150 mil) X4003S8Z-2.7 (Note) X4003 ZF X4005S8Z-2.7 (Note) X4005 ZF 0 to +70 8 Ld SOIC MDP0027 (150 mil) (Pb-free) FN8113 Rev 2.00 June 30, 2008 2.7 to 5.5 M8.118 2.55 to 2.7 M8.118 MDP0027 M8.118 MDP0027 Page 2 of 16 X4003, X4005 Ordering Information (Continued) PART NUMBER RESET (ACTIVE LOW) PART MARKING X4003S8I-2.7A X4003 AP X4003S8IZ-2.7A (Note) PART NUMBER RESET (ACTIVE HIGH) X4005S8I-2.7A PART VCC RANGE VTRIP RANGE TEMP. RANGE MARKING (V) (V) (°C) X4005 AP 2.7 to 3.6 2.85 to 3.0 PACKAGE PKG. DWG. # -40 to +85 8 Ld SOIC (150 mil) X4003 ZAP X4005S8IZ-2.7A X4005 ZAP (Note) -40 to +85 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8I-2.7A ACM X4005M8I-2.7A ACV -40 to +85 8 Ld MSOP (3.0mm) X4003M8IZ-2.7A (Note) DAC X4005M8IZ-2.7A DAL (Note) -40 to +85 8 Ld MSOP M8.118 (3.0mm) (Pb-free) X4003S8I-2.7 X4003 G X4005S8I-2.7 X4005 G -40 to +85 8 Ld SOIC (150 mil) X4003S8IZ-2.7 (Note) X4003 ZG X4005S8IZ-2.7 (Note) X4005 ZG -40 to +85 8 Ld SOIC MDP0027 (150 mil) (Pb-free) X4003M8I-2.7 ACO X4005M8I-2.7 ACX -40 to +85 8 Ld MSOP (3.0mm) X4003M8IZ-2.7 (Note) DAB X4005M8IZ-2.7 (Note) DAK -40 to +85 8 Ld MSOP M8.118 (3.0mm) (Pb-free) 2.55 to 2.7 MDP0027 M8.118 MDP0027 M8.118 NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD020. Pin Descriptions PIN NUMBER (MSOP) NAME 1 NC No internal connections 2 NC No internal connections 3 RESET/RESET 4 VSS Ground 5 SDA Serial Data. SDA is a bidirectional pin used to transfer data into and out of the device. It has an open drain output and may be wire ORed with other open drain or open collector outputs. This pin requires a pull-up resistor and the input buffer is always active (not gated). Watchdog Input. A HIGH to LOW transition on the SDA while SCL also toggles from HIGH to LOW follow by a stop condition resets the watchdog timer. The absence of this procedure within the watchdog time-out period results in RESET/RESET going active. 6 SCL Serial Clock. The serial clock controls the serial bus timing for data input and output. 7 WP Write Protect. WP HIGH prevents changes to the watchdog timer setting. 8 VCC Supply voltage FN8113 Rev 2.00 June 30, 2008 FUNCTION Reset Output. RESET/RESET is an active LOW/HIGH, open drain output which goes active whenever VCC falls below the minimum VCC sense level. It will remain active until VCC rises above the minimum VCC sense level for 250ms. RESET/RESET goes active if the watchdog timer is enabled and SDA remains either HIGH or LOW longer than the selectable Watchdog time out period. A falling edge of SDA, while SCL also toggles from HIGH to LOW followed by a stop condition resets the watchdog timer. RESET/RESET goes active on power-up and remains active for 250ms after the power supply stabilizes. Page 3 of 16 X4003, X4005 Principles of Operation 0.6µs Power-on Reset 0.6µs SCL Application of power to the X4003/X4005 activates a power-on reset circuit that pulls the RESET/RESET pin active. This signal provides several benefits: SDA • It prevents the system microprocessor from starting to operate with insufficient voltage. START CONDITION • It prevents the processor from operating prior to stabilization of the oscillator. RESTART STOP CONDITION FIGURE 1. WATCHDOG RESTART VCC Threshold Reset Procedure • It allows time for an FPGA to download its configuration prior to initialization of the circuit. The X4003/X4005 is shipped with a standard VCC threshold (VTRIP) voltage. This value will not change over normal operating and storage conditions. However, in applications where the standard VTRIP is not exactly right, or if higher precision is needed in the VTRIP value, the X4003/X4005 threshold may be adjusted. The procedure is described in the following and uses the application of a nonvolatile control signal. When VCC exceeds the device VTRIP threshold value for 200ms (nominal) the circuit releases RESET/RESET, allowing the system to begin operation. Low Voltage Monitoring During operation, the X4003/X4005 monitors the VCC level and asserts RESET/RESET if supply voltage falls below a preset minimum VTRIP. The RESET/RESET signal prevents the microprocessor from operating in a power fail or brownout condition. The RESET/RESET signal remains active until the voltage drops below 1V. It also remains active until VCC returns and exceeds VTRIP for 200ms. Setting the VTRIP Voltage This procedure is used to set the VTRIP to a higher voltage value. For example, if the current VTRIP is 4.4V and the new VTRIP is 4.6V, this procedure will directly make the change. If the new setting is to be lower than the current setting, then it is necessary to reset the trip point before setting the new value. Watchdog Timer The watchdog timer circuit monitors the microprocessor activity by monitoring the SDA and SCL pins. The microprocessor must toggle the SDA pin HIGH to LOW periodically, while SCL also toggles from HIGH to LOW (this is a start bit) followed by a stop condition prior to the expiration of the watchdog time-out period to prevent a RESET/RESET signal. The state of two nonvolatile control bits in the control register determine the watchdog timer period. The microprocessor can change these watchdog bits, or they may be “locked” by tying the WP pin HIGH. To set the new VTRIP voltage, apply the desired VTRIP threshold voltage to the VCC pin and tie the WP pin to the programming voltage VP. Then write data 00hto address 01h. The stop bit following a valid write operation initiates the VTRIP programing sequence. Bring WP LOW to complete the operation. VP = 15V TO 18V WP 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCL SDA A0h 01h 00h FIGURE 2. SET VTRIP LEVEL SEQUENCE (VCC = DESIRED VTRIP VALUE) FN8113 Rev 2.00 June 30, 2008 Page 4 of 16 X4003, X4005 VP = 15V TO 18V WP 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCL SDA A0h 00h 03h FIGURE 3. RESET VTRIP LEVEL SEQUENCE (VCC > 3V. WP = 15V TO 18V) VP ADJUST 4.7k RESET/RESET 1 2 VTRIP ADJ. 3 µC 8 X4003 X4005 4 7 6 RUN 5 SCL SDA FIGURE 4. SAMPLE VTRIP RESET CIRCUIT Resetting the VTRIP Voltage This procedure is used to set the VTRIP to a “native” voltage level. For example, if the current VTRIP is 4.4V and the new VTRIP must be 4.0V, then the VTRIP must be reset. When VTRIP is reset, the new VTRIP is something less than 1.7V. This procedure must be used to set the voltage to a lower value. To reset the new VTRIP voltage, apply the desired VTRIP threshold voltage to the VCC pin and tie the WP pin to the programming voltage VP. Then write 00h to address 03h. The stop bit of a valid write operation initiates the VTRIP programming sequence. Bring WP LOW to complete the operation. FN8113 Rev 2.00 June 30, 2008 Page 5 of 16 X4003, X4005 VTRIP PROGRAMMING EXECUTE RESET VTRIP SEQUENCE SET VCC = VCC APPLIED = DESIRED VTRIP EXECUTE SET VTRIP SEQUENCE NEW VCC APPLIED = OLD VCC APPLIED - ERROR EXECUTE RESET VTRIP SEQUENCE NEW VCC APPLIED = OLD VCC APPLIED + ERROR APPLY 5V TO VCC DECREMENT VCC (VCC = VCC - 50MV) NO RESET PIN GOES ACTIVE? YES ERROR  EMAX ERROR  –EMAX MEASURED VTRIP DESIRED VTRIP -EMAX < ERROR < EMAX EMAX = MAXIMUM ALLOWABLE VTRIP ERROR DONE FIGURE 5. VTRIP PROGRAMMING SEQUENCE Control Register The control register provides the user a mechanism for changing the watchdog timer settings. Watchdog timer bits are nonvolatile and do not change when power is removed. The control register is accessed with a special preamble in the slave byte (1011) and is located at address 1FFh. It can only be modified by performing a control register write operation. Only one data byte is allowed for each register write operation. Prior to writing to the control register, the WEL and RWEL bits must be set using a two step process, with the whole sequence requiring 3 steps. See "Writing to the Control Register" on page 7. The user must issue a stop after sending the control byte to the register to initiate the nonvolatile cycle that stores WD1 and WD0. The X4003/X4005 will not acknowledge any data bytes written after the first byte is entered. FN8113 Rev 2.00 June 30, 2008 The state of the control register can be read at any time by performing a serial read operation. Only one byte is read by each register read operation. The X4003/X4005 resets itself after the first byte is read. The master should supply a stop condition to be consistent with the bus protocol, but a stop is not required to end this operation. 7 6 5 4 3 2 1 0 0 WD1 WD0 0 0 RWEL WEL 0 RWEL: Register Write Enable Latch (Volatile) The RWEL bit must be set to “1” prior to a write to the control register. Page 6 of 16 X4003, X4005 WEL: Write Enable Latch (Volatile) The WEL bit controls the access to the control register during a write operation. This bit is a volatile latch that powers up in the LOW (disabled) state. While the WEL bit is LOW, writes the control register will be ignored (no acknowledge will be issued after the data byte). The WEL bit is set by writing a “1” to the WEL bit and zeroes to the other bits of the control register. Once set, WEL remains set until either it is reset to 0 (by writing a “0” to the WEL bit and zeroes to the other bits of the control register) or until the part powers up again. Writes to the WEL bit do not cause a nonvolatile write cycle, so the device is ready for the next operation immediately after the stop condition. WD1, WD0: Watchdog Timer Bits 0010 in binary, where xy are the WD bits. (Operation preceeded by a start and ended with a stop.) Since this is a nonvolatile write cycle it will take up to 10ms to complete. The RWEL bit is reset by this cycle and the sequence must be repeated to change the nonvolatile bits again. If bit 2 is set to ‘1’ in this third step (0xy0 0110) then the RWEL bit is set, but the WD1 and WD0 bits remain unchanged. Writing a second byte to the control register is not allowed. Doing so aborts the write operation and returns a NACK. • A read operation occurring between any of the previous operations will not interrupt the register write operation. • The RWEL bit cannot be reset without writing to the nonvolatile control bits in the control register, power cycling the device or attempting a write to a write protected block. To illustrate, a sequence of writes to the device consisting of [02H, 06H, 02H] will reset all of the nonvolatile bits in the control register to 0. A sequence of [02H, 06H, 06H] will leave the nonvolatile bits unchanged and the RWEL bit remains set. The bits WD1 and WD0 control the period of the watchdog timer. The options are shown in the following: WD1 WD0 WATCHDOG TIME-OUT PERIOD 0 0 1.4s Serial Interface 0 1 600ms Serial Interface Conventions 1 0 200ms 1 1 Disabled (factory setting) The device supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is called the master and the device being controlled is called the slave. The master always initiates data transfers, and provides the clock for both transmit and receive operations. Therefore, the devices in this family operate as slaves in all applications. Writing to the Control Register Changing any of the nonvolatile bits of the control register requires the following steps: • Write a 02H to the control register to set the write enable latch (WEL). This is a volatile operation, so there is no delay after the write. (Operation preceeded by a start and ended with a stop.) • Write a 06H to the control register to set both the register write enable latch (RWEL) and the WEL bit. This is also a volatile cycle. The zeros in the data byte are required. (Operation preceeded by a start and ended with a stop.) Serial Clock and Data Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions. See Figure 6. • Write a value to the control register that has all the control bits set to the desired state. This can be represented as 0xy0 SCL SDA DATA STABLE DATA CHANGE DATA STABLE FIGURE 6. VALID DATA CHANGES ON THE SDA BUS FN8113 Rev 2.00 June 30, 2008 Page 7 of 16 X4003, X4005 SCL SDA START STOP FIGURE 7. VALID START AND STOP CONDITIONS SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER ACKNOWLEDGE FIGURE 8. ACKNOWLEDGE RESPONSE FROM RECEIVER SDA BUS SLAVE ADDRESS BYTE ADDRESS 1 0 1 1 0 0 1 0 1 1 1 1 1 1 1 1 SIGNALS FROM THE SLAVE A C K DATA A C K STOP SIGNALS FROM THE MASTER START START A C K FIGURE 9. WRITE CONTROL REGISTER SEQUENCE Serial Start Condition All commands are preceded by the start condition, which is a HIGH to LOW transition of SDA when SCL is HIGH. The device continuously monitors the SDA and SCL lines for the start condition and will not respond to any command until this condition has been met. See Figure 7. Serial Stop Condition All communications must be terminated by a stop condition, which is a LOW to HIGH transition of SDA when SCL is HIGH. The stop condition is also used to place the device into the Standby power mode after a read sequence. A stop condition can only be issued after the transmitting device has released the bus. See Figure 7. Serial Acknowledge Acknowledge is a software convention used to indicate successful data transfer. The transmitting device, either master or slave, will release the bus after transmitting eight bits. During the ninth clock cycle, the receiver will pull the SDA line FN8113 Rev 2.00 June 30, 2008 LOW to acknowledge that it received the eight bits of data. Refer to Figure 8. The device will respond with an acknowledge after recognition of a start condition and the correct contents of the slave address byte. Acknowledge bits are also provided by the X4003/4005 after correct reception of the control register address byte, after receiving the byte written to the control register and after the second slave address in a read question (see Figures 9 and 10). Serial Write Operations Slave Address Byte Following a start condition, the master must output a slave address byte. This byte consists of several parts: • a device type identifier that is always ‘1011’. • two bits of ‘0’. • one bit of the slave command byte is a R/W bit. The R/W bit of the slave address byte defines the operation to be Page 8 of 16 X4003, X4005 performed. When the R/W bit is a one, then a read operation is selected. A zero selects a write operation. Refer to Figure 9. • After loading the entire slave address byte from the SDA bus, the device compares the input slave byte data to the proper slave byte. Upon a correct compare, the device outputs an acknowledge on the SDA line. Write Control Register To write to the control register, the device requires the slave address byte and a byte address. This gives the master access to register. After receipt of the address byte, the device responds with an acknowledge, and awaits the data. After receiving the 8 bits of the data byte, the device again responds with an acknowledge. The master then terminates the transfer by generating a stop condition, at which time the device begins the internal write cycle to the nonvolatile memory. During this internal write cycle, the device inputs are disabled, so the device will not respond to any requests from the master. If WP is HIGH, the control register cannot be changed. A write to the control register will suppress the acknowledge bit and no data in the control register will change. With WP low, a second byte written to the control register terminates the operation and no write occurs. Stops and Write Modes Stop conditions that terminate write operations must be sent by the master after sending 1 full data byte plus the subsequent ACK signal. If a stop is issued in the middle of a data byte, or before 1 full data byte plus its associated ACK is sent, then the device will reset itself without performing the write. condition. Refer to Figure 10 for the address, acknowledge, and data transfer sequences. Operational Notes The device powers-up in the following state: • The device is in the low power standby state. • The WEL bit is set to ‘0’. In this state it is not possible to write to the device. • SDA pin is the input mode. RESET/RESET signal is active for tPURST. Data Protection The following circuitry has been included to prevent inadvertent writes: • The WEL bit must be set to allow a write operation. • The proper clock count and bit sequence is required prior to the stop bit in order to start a nonvolatile write cycle. • A three step sequence is required before writing into the control register to change watchdog timer or block lock settings. • The WP pin, when held HIGH, prevents all writes to the control register. • Communication to the device is inhibited below the VTRIP voltage. • Command to change the control register are terminated if inprogress when RESET/RESET go active. Symbol Table Serial Read Operations WAVEFORM The read operation allows the master to access the control register. To conform to the I2C standard, prior to issuing the slave address byte with the R/W bit set to one, the master must first perform a “dummy” write operation. The master issues the start condition and the slave address byte, receives an acknowledge, then issues the byte address. After acknowledging receipt of the byte address, the master immediately issues another start condition and the slave address byte with the R/W bit set to one. This is followed by an acknowledge from the device and then by the eight bit control register. The master terminates the read operation by not responding with an acknowledge and then issuing a stop SIGNALS FROM THE MASTER SDA BUS SIGNALS FROM THE SLAVE S T A R T S T A R T BYTE ADDRESS SLAVE ADDRESS 1 0 11 0 0 10 1 1 1 1 11 1 1 A C K INPUTS OUTPUTS Must be steady Will be steady May change from LOW to HIGH Will change from LOW to HIGH May change from HIGH to LOW Will change from HIGH to LOW Don’t Care: Changes Allowed Changing: State Not Known N/A Center Line is High Impedance S T O P SLAVE ADDRESS 10 1 10 01 1 A C K A C K DATA FIGURE 10. CONTROL REGISTER READ SEQUENCE FN8113 Rev 2.00 June 30, 2008 Page 9 of 16 X4003, X4005 Absolute Maximum Ratings Thermal Information Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Voltage on any Pin with Respect to VSS . . . . . . . . . . . . -1.0V to +7V DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commerical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C DC Operating Characteristics Over the recommended operating conditions unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS VCC = 1.8 TO 3.6V VCC = 2.7 TO 5.5V MIN MIN MAX MAX UNIT ICC (Note 1) Active Supply Current Read Control Register fSCL = 400kHz nonvolatile, SDA = Open 0.5 1.0 mA ICC2 (Note 1) Active Supply Current Write Control Register fSCL = 400kHz nonvolatile, SDA = Open 1.5 3.0 mA ICC3 (Note 2) Operating Current AC (WDT Off) fSCL = 400kHz nonvolatile, SDA = Open 1 1 µA ICC4 (Note 2) Operating Current DC (WDT Off) VSDA = VSCL = VCC Others = GND or VSB 1 1 µA ICC5 (Note 2) Operating Current DC (WDT On) VSDA = VSCL = VCC Others = GND or VSB 10 20 µA ILI Input Leakage Current VIN = GND to VCC 10 10 µA ILO Output Leakage Current VSDA = GND to VCC Device is in Standby (Note 2) 10 10 µA VIL (Note 3) Input LOW Voltage -0.5 VCC x 0.3 -0.5 VCC x 0.3 V VIH (Note 3) Input HIGH Voltage VCC x 0.7 VCC + 0.5 VCC x 0.7 VCC + 0.5 V VHYS Schmitt Trigger Input Hysteresis Fixed Input Level VCC Related Level VOL Output LOW Voltage 0.2 0.2 V 0.05 x VCC 0.05 x VCC V IOL = 3.0mA (2.7V to 5.5V) IOL = 1.8mA (1.8V to 3.6V) 0.4 0.4 V NOTES: 1. The device enters the active state after any start, and remains active until: 9 clock cycles later if the device select bits in the slave address byte are incorrect; 200ns after a stop ending a read operation; or tWC after a stop ending a write operation. 2. The device goes into standby: 200ns after any stop, except those that initiate a nonvolatile write cycle; tWC after a stop that initiates a nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct device select bits in the slave address byte. 3. VIL min. and VIH max. are for reference only and are not tested. Capacitance (TA = +25°C, f = 1.0 MHz, VCC = 5V) SYMBOL COUT CIN PARAMETER TYP UNIT TEST CONDITIONS Output Capacitance (SDA, RESET/RESET) 8 pF VOUT = 0V Input Capacitance (SCL, WP) 6 pF VIN = 0V FN8113 Rev 2.00 June 30, 2008 Page 10 of 16 X4003, X4005 AC Test Conditions Equivalent AC Load Circuit 5V 5V 1533 For VOL = 0.4V and IOL = 3mA SDA 4.6k RESET RESET 100pF AC Electrical Specifications Input pulse levels 0.1VCC to 0.9VCC Input rise and fall times 10ns Input and output timing levels 0.5VCC Output load Standard output load 100pF Over recommended operating conditions, unless otherwise specified. 100kHz SYMBOL fSCL PARAMETER SCL Clock Frequency 400kHz MIN MAX MIN MAX UNIT 0 100 0 400 kHz tIN Pulse Width Suppression Time at Inputs n/a n/a 50 tAA SCL LOW to SDA Data Out Valid 0.1 0.9 0.1 tBUF Time the Bus Free Before Start of New Transmission 4.7 1.3 µs tLOW Clock LOW Time 4.7 1.3 µs tHIGH Clock HIGH Time 4.0 0.6 µs tSU:STA Start Condition Set-up Time 4.7 0.6 µs tHD:STA Start Condition Hold Time 4.0 0.6 µs tSU:DAT Data in Setup Time 250 100 ns tHD:DAT Data in Hold Time 5.0 0 µs tSU:STO Stop Condition Set-up Time 0.6 0.6 µs tDH Data Output Hold Time 50 50 ns tR SDA and SCL Rise Time 1000 20 + 0.1Cb (Note 5) 300 ns tF SDA and SCL Fall Time 300 20 + 0.1Cb (Note 5) 300 ns tSU:WP WP Set-up Time tHD:WP WP Hold Time Cb Capacitive Load for Each Bus Line ns 0.9 µs 0.4 0.6 µs 0 0 µs 400 400 pF NOTES: 4. Typical values are for TA = +25°C and VCC = 5.0V 5. Cb = total capacitance of one bus line in pF FN8113 Rev 2.00 June 30, 2008 Page 11 of 16 X4003, X4005 Timing Diagrams Bus Timing tF tHIGH SCL tLOW tR tSU:DAT tSU:STA SDA IN tSU:STO tHD:DAT tHD:STA tA tBUF tDH SDA OUT WP Pin Timing START SCL CLK 1 CLK 9 SLAVE ADDRESS BYTE SDA IN tSU:WP tHD:WP WP Write Cycle Timing SCL SDA 8TH BIT OF LAST BYTE ACK tWC STOP CONDITION START CONDITION Nonvolatile Write Cycle Timing SYMBOL tWC (Note 6) PARAMETER Write Cycle Time MIN TYP (Note 1) MAX UNIT 5 10 ms NOTE: 6. tWC is the time from a valid stop condition at the end of a write sequence to the end of the self-timed internal nonvolatile write cycle. It is the minimum cycle time to be allowed for any nonvolatile write by the user, unless Acknowledge Polling is used. FN8113 Rev 2.00 June 30, 2008 Page 12 of 16 X4003, X4005 Power-Up and Power-Down Timing VTRIP VCC tPURST 0V tPURST tR tF tRPD RESET VRVALID RESET VRVALID RESET/RESET Output Timing SYMBOL VTRIP tPURST tRPD PARAMETER MIN TYP MAX UNIT Reset Trip Point Voltage, X4003-4.5A, X4005-4.5A 4.5 4.62 4.75 V Reset Trip Point Voltage, X4003, X4005 4.25 4.38 4.5 V Reset Trip Point Voltage, X4003-2.7A, X4005-2.7A 2.85 2.92 3.0 V Reset Trip Point Voltage, X4003-2.7, X4005-2.7 2.55 2.62 2.7 V Reset Trip Point Voltage, X4003-1.8, X4005-1.8 1.7 1.75 1.8 V Power-up Reset Time-out 100 200 400 ms VCC Detect to Reset Output 500 ns tF VCC Fall Time 10 ms tR VCC Rise Time 0.1 ns VRVALID Reset Valid VCC 1 V SDA vs RESET/RESET Timing SCL SDA tCST RESET tWDO tWDO tRST tRST RESET RESET/RESET Output Timing SYMBOL tWDO PARAMETER MIN TYP MAX UNIT ms Watchdog Time-out Period WD1 = 1, WD0 = 1 (factory setting) OFF WD1 = 1, WD0 = 0 100 200 300 WD1 = 0, WD0 = 1 450 600 800 ms WD1 = 0, WD0 = 0 1 1.4 2 sec 200 400 ms tCST CS Pulse Width to Reset the Watchdog 400 tRST Reset Time-out 100 FN8113 Rev 2.00 June 30, 2008 ns Page 13 of 16 X4003, X4005 VTRIP Programming Timing Diagram VCC (VTRIP) VTRIP tTHD tTSU VP WP tVPH tVPO tVPS SCL tRP SDA 01h OR 03h 00h A0h VTRIP Programming Parameters PARAMETER DESCRIPTION MIN MAX UNIT tVPS VTRIP Program Enable Voltage Set-up Time 1 µs tVPH VTRIP Program Enable Voltage Hold Time 1 µs tTSU VTRIP Set-up Time 1 µs tTHD VTRIP Hold (Stable) Time 10 ms tWC VTRIP Write Cycle Time tVPO VTRIP Program Enable Voltage Off Time (Between Successive Adjustments) 0 µs tRP VTRIP Program Recovery Period (Between Successive Adjustments) 10 ms VP Programming Voltage 15 18 V VTRIP Programmed Voltage Range 1.7 5.0 V Vta1 Initial VTRIP Program Voltage Accuracy (VCC Applied - VTRIP) (Programmed At +25°C.) -0.1 +0.4 V Vta2 Subsequent VTRIP Program Voltage Accuracy [(VCC Applied - Vta1) - VTRIP. programmed at +25°C.) -25 +25 mV Vtr VTRIP Program Voltage Repeatability (Successive Program Operations. Programmed at +25°C.) -25 +25 mV Vtv VTRIP Program Variation After Programming (0°C to +75°C). (Programmed at +25°C) -25 +25 mV VTRAN 10 ms © Copyright Intersil Americas LLC 2005-2008. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN8113 Rev 2.00 June 30, 2008 Page 14 of 16 X4003, X4005 Mini Small Outline Plastic Packages (MSOP) N M8.118 (JEDEC MO-187AA) 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE E1 INCHES E -B- INDEX AREA 1 2 0.20 (0.008) A B C TOP VIEW 4X  0.25 (0.010) R1 R GAUGE PLANE SEATING PLANE -CA 4X  A2 A1 b -H- 0.10 (0.004) L1 SEATING PLANE C D 0.20 (0.008) C a CL E1 0.20 (0.008) C D MAX MIN MAX NOTES 0.037 0.043 0.94 1.10 - A1 0.002 0.006 0.05 0.15 - A2 0.030 0.037 0.75 0.95 - b 0.010 0.014 0.25 0.36 9 c 0.004 0.008 0.09 0.20 - D 0.116 0.120 2.95 3.05 3 E1 0.116 0.120 2.95 3.05 4 0.026 BSC -B- 0.65 BSC - E 0.187 0.199 4.75 5.05 - L 0.016 0.028 0.40 0.70 6 0.037 REF N C SIDE VIEW MIN A L1 -A- e SYMBOL e L MILLIMETERS 0.95 REF 8 R 0.003 R1 0  - 8 - 0.07 0.003 - 5o 15o 0o 6o 7 - - 0.07 - - 5o 15o - 0o 6o Rev. 2 01/03 END VIEW NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-187BA. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. Dimension “D” does not include mold flash, protrusions or gate burrs and are measured at Datum Plane. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions and are measured at Datum Plane. - H - Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. Formed leads shall be planar with respect to one another within 0.10mm (0.004) at seating Plane. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Datums -A -H- . and - B - to be determined at Datum plane 11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. FN8113 Rev 2.00 June 30, 2008 Page 15 of 16 X4003, X4005 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 NOTES: Rev. M 2/07 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 FN8113 Rev 2.00 June 30, 2008 Page 16 of 16