®
X5328, X5329
(Replaces X25328, X25329)
Data Sheet October 17, 2005 FN8132.1
CPU Supervisor with 32Kbit SPI EEPROM
FEATURES • Low VCC detection and reset assertion —Five standard reset threshold voltages —Re-program low VCC reset threshold voltage using special programming sequence —Reset signal valid to VCC = 1V • Long battery life with low power consumption — 3.3V, IOL = 2.1mA VCC ≤ 2V, IOL = 0.5mA 2V < VCC ≤ 3.3V, IOL = 1mA Test Conditions SCK = VCC x 0.1/VCC x 0.9 @ 2MHz, SO = Open SCK = VCC x 0.1/VCC x 0.9 @ 2MHz, SO = Open CS = VCC, VIN = VSS or VCC, VCC = 5.5V VIN = VSS to VCC VOUT = VSS to VCC
2V < VCC ≤ 3.3V, IOH = -0.4mA VCC ≤ 2V, IOH = -0.25mA IOL = 1mA
VCC > 3.3V, IOH = -1.0mA
CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V Symbol
COUT(2) CIN
(2)
Test
Output Capacitance (SO, RESET, RESET) Input Capacitance (SCK, SI, CS, WP)
Max.
8 6
Unit
pF pF
Conditions
VOUT = 0V VIN = 0V
Notes: (1) VIL min. and VIH max. are for reference only and are not tested. (2) This parameter is periodically sampled and not 100% tested.
12
FN8132.1 October 17, 2005
X5328, X5329
EQUIVALENT A.C. LOAD CIRCUIT AT 5V VCC
5V 2.06kΩ Output 3.03kΩ 100pF RESET/RESET 30pF 5V 4.6kΩ
A.C. TEST CONDITIONS
Input pulse levels Input rise and fall times Input and output timing level VCC x 0.1 to VCC x 0.9 10ns VCC x0.5
A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Serial Input Timing 2.7-5.5V Symbol
fSCK tCYC tLEAD tLAG tWH tWL tSU tH tRI(3) tFI(3) tCS tWC
(4)
Parameter
Clock Frequency Cycle Time CS Lead Time CS Lag Time Clock HIGH Time Clock LOW Time Data Setup Time Data Hold Time Input Rise Time Input Fall Time CS Deselect Time Write Cycle Time
Min.
0 500 250 250 200 250 50 50
Max.
2
Unit
MHz ns ns ns ns ns ns ns
100 100 500 10
ns ns ns ms
13
FN8132.1 October 17, 2005
X5328, X5329
Serial Input Timing
tCS CS tLEAD SCK tSU SI MSB IN tH tRI tFI LSB IN tLAG
SO
High Impedance
Serial Output Timing 2.7-5.5V Symbol
fSCK tDIS tV tHO tRO tFO
(3) (3)
Parameter
Clock Frequency Output Disable Time Output Valid from Clock Low Output Hold Time Output Rise Time Output Fall Time
Min.
0
Max.
2 250 250
Unit
MHz ns ns ns ns ns
0 100 100
Notes: (3) This parameter is periodically sampled and not 100% tested. (4) tWC is the time from the rising edge of CS after a valid write sequence has been sent to the end of the self-timed internal nonvolatile write cycle.
Serial Output Timing
CS tCYC SCK tV SO MSB Out MSB–1 Out tHO tWL LSB Out tDIS tWH tLAG
SI
ADDR LSB IN
14
FN8132.1 October 17, 2005
X5328, X5329
Power-Up and Power-Down Timing
VTRIP VCC 0 Volts tR RESET (X5328) tPURST tPURST tF tRPD VTRIP
RESET (X5329)
RESET Output Timing Symbol
VTRIP
Parameter
Reset Trip Point Voltage, X5328-4.5A, X5328-4.5A Reset Trip Point Voltage, X5328, X5329 Reset Trip Point Voltage, X5328-2.7A, X5329-2.7A Reset Trip Point Voltage, X5328-2.7, X5329-2.7 VTRIP Hysteresis (HIGH to LOW vs. LOW to HIGH VTRIP voltage) Power-up Reset Time Out VCC Detect to Reset/Output VCC Fall Time VCC Rise Time Reset Valid VCC
Min.
4.5 4.25 2.85 2.55 100 100 100 1
Typ.
4.63 4.38 2.93 2.63 20 200
Max.
4.75 4.5 3.0 2.7 280 500
Unit
V
VTH tPURST tRPD(5) tF(5) tR
Note:
(5)
mV ms ns µs µs V
VRVALID
(5) This parameter is periodically sampled and not 100% tested.
15
FN8132.1 October 17, 2005
X5328, X5329
VTRIP Set Conditions
tTHD VCC VTRIP tTSU tVPS tP tVPH tRP
CS
tVPS VP
tVPH
tVPO
SCK VP SI tVPO
VTRIP Reset Conditions
VCC* tRP tVPS tP tVP1
CS
tVPS
tVPH
tVPO
SCK
VCC
VP SI
tVPO
*VCC > Programmed VTRIP
16
FN8132.1 October 17, 2005
X5328, X5329
VTRIP Programming Specifications VCC = 1.7-5.5V; Temperature = 0°C to 70°C Parameter
tVPS tVPH tP tTSU tTHD tWC tRP tVPO VP VTRAN Vta1 Vta2 Vtr Vtv
Description
SCK VTRIP Program Voltage Setup time SCK VTRIP Program Voltage Hold time VTRIP Program Pulse Width VTRIP Level Setup time VTRIP Level Hold (stable) time VTRIP Write Cycle Time VTRIP Program Cycle Recovery Period (Between successive programming cycles) SCK VTRIP Program Voltage Off time before next cycle Programming Voltage VTRIP Programed Voltage Range Initial VTRIP Program Voltage accuracy (VCC applied-VTRIP) (Programmed at 25°C.) Subsequent VTRIP Program Voltage accuracy [(VCC applied-Vta1)-VTRIP] (Programmed at 25°C.) VTRIP Program Voltage repeatability (Successive program operations.) (programmed at 25°C) VTRIP Program variation after programming (0-75°C). (programmed at 25°C)
Min.
1 1 1 10 10
Max.
Unit
µs µs µs µs ms
10 10 0 15 1.7 -0.1 -25 -25 -25 18 5.0 +0.4 +25 +25 +25
ms ms ms V V V mV mV mV
VTRIP programming parameters are periodically sampled and are not 100% tested.
17
FN8132.1 October 17, 2005
X5328, X5329
TYPICAL PERFORMANCE
VCC Supply Current vs. Temperature (ISB)
2
tPURST vs. Temperature
205 200 195 190 Time (ms) 185 180 175 170 165
Isb (µA)
1
(VCC = 3V, 5V)
0 -40C
160 -40 25C Temp°C 90C
25 Degrees °C
90
VTRIP vs. Temperature (programmed at 25°C)
5.025 5.000 4.975 3.525 Voltage 3.500 3.475 2.525 2.500 2.475 0 25 Temperature 85 VTRIP = 2.5V VTRIP = 3.5V VTRIP = 5V
18
FN8132.1 October 17, 2005
X5328, X5329
PACKAGING INFORMATION 8-Lead Plastic Dual In-Line Package Type P
0.430 (10.92) 0.360 (9.14)
0.260 (6.60) 0.240 (6.10) Pin 1 Index Pin 1 0.300 (7.62) Ref. 0.060 (1.52) 0.020 (0.51)
Half Shoulder Width On All End Pins Optional Seating Plane 0.150 (3.81) 0.125 (3.18)
0.145 (3.68) 0.128 (3.25) 0.025 (0.64) 0.015 (0.38) 0.065 (1.65) 0.045 (1.14) 0.020 (0.51) 0.016 (0.41)
0.110 (2.79) 0.090 (2.29)
.073 (1.84) Max.
0.325 (8.25) 0.300 (7.62)
Typ. 0.010 (0.25)
0° 15°
NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
19
FN8132.1 October 17, 2005
X5328, X5329
PACKAGING INFORMATION 8-Lead Plastic Small Outline Gull Wing Package Type S
0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1
0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7°
0.053 (1.35) 0.069 (1.75) 0.004 (0.19) 0.010 (0.25)
0.050 (1.27)
0.010 (0.25) X 45° 0.020 (0.50)
0.050" Typical
0° - 8° 0.0075 (0.19) 0.010 (0.25) 0.016 (0.410) 0.037 (0.937) 0.250"
0.050" Typical
FOOTPRINT
0.030" Typical 8 Places
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
20
FN8132.1 October 17, 2005
X5328, X5329
PACKAGING INFORMATION 14-Lead Plastic Small Outline Gullwing Package Type S
0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) Pin 1 Index Pin 1
0.014 (0.35) 0.020 (0.51) 0.336 (8.55) 0.345 (8.75) (4X) 7°
0.053 (1.35) 0.069 (1.75) 0.004 (0.10) 0.010 (0.25)
0.050 (1.27)
0.050"T ypical 0.010 (0.25) 0.020 (0.50) X 45° 0.050"Typical 0° - 8° 0.0075 (0.19) 0.010 (0.25) 0.016 (0.410) 0.037 (0.937) 0.030" Typical 14 Places 0.250"
FOOTPRINT
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 21
FN8132.1 October 17, 2005