CS4N65A3R

Silicon N-Channel Power MOSFET R ○ CS4N65 A3R General Description： 650 V ID 4 A VDMOSFETs, is obtained by the self-aligned planar Technology PD(TC=25℃) 75 W which reduce the conduction loss, improve switching RDS(ON)Typ 2.4 Ω CS4N65 A3R, the silicon N-channel Enhanced VDSS performance and enhance the avalanche energy. The transistor can be used in various power switching circuit for system miniaturization and higher efficiency. The package form is TO-251, which accords with the RoHS standard. Features： l Fast Switching l Low ON Resistance(Rdson≤2.8Ω) l Low Gate Charge (Typical Data: 14.5nC) l Low Reverse transfer capacitances(Typical:3.5pF) l 100% Single Pulse avalanche energy Test Applications： Power switch circuit of adaptor and charger. Absolute（Tc= 25℃ unless otherwise specified）： Symbol Parameter VDSS Drain-to-Source Voltage Rating Units 650 V 4 A 2.5 A 16 A Gate-to-Source Voltage ±30 V Single Pulse Avalanche Energy 200 mJ Peak Diode Recovery dv/dt 5.0 V/ns Power Dissipation 75 W 0.60 W/℃ 150，–55 to 150 ℃ 300 ℃ Continuous Drain Current ID IDM Continuous Drain Current T C = 100 °C a1 Pulsed Drain Current VGS EAS a2 dv/dt a3 PD Derating Factor above 25°C TJ，T stg Operating Junction and Storage Temperature Range TL Maximum Temperature for Soldering W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 1 of 1 0 2 0 1 5 V0 1 CS4N65 A3R R ○ Electrical Characteristics（Tc= 25℃ unless otherwise specified）： OFF Characteristics Symbol Parameter Test Conditions VDSS Drain to Source Breakdown Voltage VGS=0V, ID =250µA ΔBVDSS/ΔT J Bvdss Temperature Coefficient ID=250uA,Reference25℃ IDSS Drain to Source Leakage Current VDS =650V, V GS= 0V, Ta = 25℃ VDS =520V, V GS= 0V, Ta = 125℃ IGSS(F) Gate to Source Forward Leakage IGSS(R) Gate to Source Reverse Leakage Rating Unit s Min. Typ. Max. 650 -- -- V -- 0.67 -- V/℃ -- -- 1 µA -- -- 100 µA VGS =+30V -- -- 100 nA VGS =-30V -- -- -100 nA ON Characteristics Symbol Parameter Test Conditions R DS(ON) Drain-to-Source On-Resistance VGS=10V,ID =2A VGS(TH) Gate Threshold Voltage VDS = V GS , ID = 250µA Rating Units Min. Typ. Max. -- 2.4 2.8 Ω 2.0 -- 4.0 V Pulse width tp≤300µs,δ≤2% Dynamic Characteristics Symbol Parameter Test Conditions g fs Forward Transconductance VDS=15V, ID =2A C iss Input Capacitance C oss Output Capacitance C rss Reverse Transfer Capacitance VGS = 0V V DS = 25V f = 1.0MHz Rating Min. Typ. Max. -- 3.5 -- -- 610 -- -- 53 -- -- 3.5 -- Units S pF Resistive Switching Characteristics Symbol Parameter td(ON) Turn-on Delay Time tr Rise Time td(OFF) Turn-Off Delay Time tf Fall Time Qg Total Gate Charge Qgs Gate to Source Charge Qgd Gate to Drain (“Miller”)Charge Test Conditions ID =4A VDD = 325V RG =10Ω ID =4A V DD =520V VGS = 10V W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Rating Min. Typ. Max. -- 14 -- -- 16 -- -- 32 -- -- 11 -- -- 14.5 -- -- 3 -- -- 6.5 -- Pag e 2 of 1 0 Units 2 0 1 5 V0 1 ns nC CS4N65 A3R R ○ Source-Drain Diode Characteristics Symbol Parameter IS Test Conditions Rating Units Min. Typ. Max. Continuous Source Current (Body Diode) -- -- 4 A ISM Maximum Pulsed Current (Body Diode) -- -- 16 A VSD Diode Forward Voltage -- -- 1.5 V trr Reverse Recovery Time -- 256 -- ns Qrr Reverse Recovery Charge -- 1200 -- nC IRRM Reverse Recovery Current -- 9.4 -- A IS =4.0A,VGS =0V IS =4.0A,Tj = 25℃ dIF /dt=100A/us, VGS=0V Pulse width tp≤300µs,δ≤2% Symbol Parameter Typ. Units R θ JC Junction-to-Case 1.67 ℃/W R θ JA Junction-to-Ambient 100 ℃/W a1 ：Repetitive rating; pulse width limited by maximum junction temperature ：L=10mH, ID=6.3A, Start TJ=25℃ a3 ：ISD =4A,di/dt ≤100A/us,VDD≤BVDS, Start T J=25℃ a2 W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 3 of 1 0 2 0 1 5 V0 1 CS4N65 A3R R ○ Characteristics Curve： 80 PD , Power Dissipation ，Watts Id , Drain Current , Amps 100 10 100us 1 1ms OPERATION IN THIS AREA MAY BE LIMITED BY RDS(ON) TJ=MAX RATED TC=25℃ Single Pulse 0 .1 10ms DC 70 60 50 40 30 20 10 0 0 .0 1 1 10 100 V d s , D r a in - t o - S o u r c e V o lta g e , V o lts 0 1000 Figure 1 Maximum Forward Bias Safe Operating Area 25 50 75 100 TC , Case Temperature , C 8 250us Pluse Test Tc = 25℃ Id , Drain Current , Amps Id , Drain Current , Amps 5 3 2 150 Figure 2 Maximum Power Dissipation vs Case Temperature 6 4 125 VGS=10V 6 VGS=7V 4 VGS=5V VGS=6V VGS=4V 2 1 0 0 0 25 75 100 125 50 TC , C ase Tem perature , C 150 Figure 3 Maximum Continuous Drain Current vs Case Temperature 0 5 10 15 20 Vds , Drain-to-Source Voltage , Volts 25 Figure 4 Typical Output Characteristics Thermal Impedance, Normalized 1 50% 20% 0.1 10% 5% PDM 2% 0.01 Single pulse 0.001 0.00001 t1 t2 1% NOTES： DUTY FACTOR ：D=t1/ t2 PEAK Tj=PDM*ZthJC*RthJC+TC 0.0001 0.001 0.01 Rectangular Pulse Duration,Seconds 0.1 1 Figure 5 Maximum Effective Thermal Impendance , Junction to Case W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 4 of 1 0 2 0 1 5 V0 1 CS4N65 A3R 8 Isd, Reverse Drain Current , Amps Id , Drain Current , Amps 9 250us Pulse Test VDS=10V 7.5 6 4.5 +25℃ 3 +150℃ 1.5 0 7 6 5 4 +150℃ 3 +25℃ 2 1 0 2 4 6 8 Vgs , Gate to Source Voltage , Volts 10 0 0.2 0.4 0.6 0.8 1 Vsd , Source - Drain Voltage , Volts 1.2 Figure 7 Typical Body Diode Transfer Characteristics Figure 6 Typical Transfer Characteristics Rds(on), Drain to Source ON Resistance, Nomalized 4 Rds(on), Drain to Source ON Resistance, Ohms R ○ PULSE DURATION = 10μs DUTY CYCLE= 0.5%MAX Tc =25 ℃ 3.5 VGS=10V 3 2.5 2 2.5 2.25 PULSE DURATION = 10μs DUTY CYCLE= 0.5%MAX VGS=10V ID=2A 2 1.75 1.5 1.25 1 0.75 0.5 0 1 2 3 Id , Drain Current , Amps Figure 8 Typical Drain to Source ON Resistance vs Drain Current 4 -50 0 50 100 Tj, Junction temperature , C Figure 9 Typical Drian to Source on Resistance vs Junction Temperature W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 5 of 1 0 2 0 1 5 V0 1 150 CS4N65 A3R 1.15 1.1 Bvdss,Drain to Source Breakdown Voltage, Normalized Vgs(th),Threshold Voltage, Nomalized 1.15 1.05 1 0.95 0.9 VGS=0V ID=250μA 0.85 0.8 0.75 1.05 VGS=0V ID=250μA 0.95 0.85 0.7 0.65 -75 -50 -25 0 25 50 75 100 125 150 175 Tj, Junction temperature , C Figure 10 Typical Theshold Voltage vs Junction Temperature 0.75 -55 -5 20 45 70 95 120 Tj, Junction temperature , C 145 170 12 Ciss 100 Coss VGS=0V , f=1MHz Ciss=Cgs+Cgd Coss=Cds+Cgd Crss=Cgd Vgs , Gate to Source Voltage ,Volts 1000 10 -30 Figure 11 Typical Breakdown Voltage vs Junction Temperature 10000 Capacitance , pF R ○ 10 VDS=520V VDS=325V VDS=130V 8 6 4 2 Crss ID=4A 0 1 0.1 1 10 Vds , Drain - Source Voltage , Volts 100 Figure 12 Typical Capacitance vs Drain to Source Voltage 0 3 6 9 Qg , Total Gate Charge , nC 12 15 Figure 13 Typical Gate Charge vs Gate to Source Voltage W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 6 of 1 0 2 0 1 5 V0 1 CS4N65 A3R R ○ Test Circuit and Waveform W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 7 of 1 0 2 0 1 5 V0 1 CS4N65 A3R W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . R ○ Pag e 8 of 1 0 2 0 1 5 V0 1 CS4N65 A3R R ○ Package Information Items A B B1 B2 C D E F G H L M N Values(mm) MIN MAX 6.30 6.90 5.20 6.30 0.70 1.30 6.80 7.40 2.10 2.50 0.30 0.60 0.50 0.86 0.30 0.60 0.70 1.00 1.40 2.40 7.50 9.80 5.90 6.50 4.40 5.80 2.10 3.90 5.10 5.50 2.09 2.49 TO-251 Package W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Pag e 9 of 1 0 2 0 1 5 V0 1 CS4N65 A3R R ○ The name and content of poisonous and harmful material in products Hazardous Substance Part’s Name Pb Hg ≤0.1% ≤0.1% Lead Frame ○ ○ Molding Compound ○ ○ Chip ○ Wire Bonding Solder Limit Cd Cr(VI) PBB PBDE DIBP DEHP DBP BBP ≤0.1% ≤0.1% ≤0.1% ≤0.1% ≤0.1% ≤0.1% ≤0.1% ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ ○ ○ ○ ○ ≤ 0.01% ○：means the hazardous material is under the criterion of SJ/T11363-2006. Note ×：means the hazardous material exceeds the criterion of SJ/T11363-2006. The plumbum element of solder exist in products presently, but within the allowed range of Eurogroup’s RoHS. Warnings 1. 2. 3. 4. Exceeding the maximum ratings of the device in performance may cause damage to the device, even the permanent failure, which may affect the dependability of the machine. It is suggested to be used under 80 percent of the maximum ratings of the device. When installing the heatsink, please pay attention to the torsional moment and the smoothness of the heatsink. VDMOSFETs is the device which is sensitive to the static electricity, it is necessary to protect the device from being damaged by the static electricity when using it. This publication is made by Huajing Microelectronics and subject to regular change without notice. WUXI CHINA RESOURCES HUAJING MICROELECTRONICS CO., LTD. Add： No.14 Liangxi RD. Wuxi, Jiangsu, China Mail:214061 http://www. crhj.com.cn Tel: +86 0510-85807228 Fax: +86- 0510-85800864 HTU Marketing Part： Post：214061 UTH Tel： +86 0510-81805277/81805336 Fax: +86 0510-85800360/85803016 E-mail：sales@hj.crmicro.com Application and Service：Post：214061 Tel / Fax：+86- 0510-81805243/81805110 W U X I C H I N A R E S O U R C E S H U A J I N G M I C R O E L E C T R O N I C S C O . , LT D . Page 10 of 10 2015V01