HFR-PAT3042SC-D-4-T

High Frequency Surface Mount Attenuators PAT Series • Frequency operation to 10 GHz • Industry standard 0805, 1206, 1612 chip sizes • Low parasitic capacitance and inductance • Thin film stability over time and temperature IRC Advanced Film Division The PAT chip attenuator series are available in a wide range of power ratings from 100mW to 250mW. The surface mount package is ideal for applications where parasitic capacitance and inductance are concerns. Typical applications include wireless communication receivers and transmitters. Electrical Data PAT1220 Impedance Frequency Range VSWR Attenuation Attenuation Tolerance TCR Power Rating Operating Temperature Range 50W DC to 10 GHz 1.3 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10dB ±0.3dB ±50ppm/°C 100mW PAT1632 50W DC to 3GHz 1.3 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 16dB 0 to 10dB: ±0.3dB 16dB: ±0.5dB ±50ppm/°C 125mW -55°C to +125°C PAT3042SC 50W DC to 3GHz 1.2 PAT3042SD 75W DC to 2GHz 1.3 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 16, 20dB 0 to 10dB: ±0.3dB 16, 20dB: ±0.5dB ±25ppm/°C 250mW Environmental Data Test Condition Short Time Overload Load Life Moisture Resistance Temperature Cycle Resistance to Solder Heat Terminal Strength Solderability Insulation Resistance 2.5 x rated voltage, 5 sec 1000 Hours, 70°C 1000 Hours, 60°C, 95% 5 Cycles, 125°C High, -55 Low 260°C, 10 sec. Fulcrum dist: 90mm, Bending width: 3mm Substrate: Glass epoxy t=1.6mm 235°C, 3 sec. 500V, 1 minute 37 A subsidiary of TT electronics plc PAT Series Issue October 2006 Sheet 1 of 3 Tolerance Attenuation ±0.02dB ±0.04dB ±0.04dB ±0.02dB ±0.02dB ±0.02dB ∆ Impedance ±0.2% ±0.5% ±0.5% ±0.2% ±0.2% ±0.2% >95% coverage >1000MW General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. © IRC Advanced Film Division • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com High Frequency Surface Mount Attenuators Physical Data L a W1 a IRC Advanced Film Division Dimensions (mm) t a1 4 b1 a1 L W t b3 3 a b W1 2 b W3 5 b b2 W2 W3 b1 2.00 ±0.10 1.25 ±0.10 0.40 ±0.10 0.50 ±0.20 0.60 ±0.20 0.40 ±0.20 0.40 ±0.20 0.35 ±0.20 0.70 ±0.10 0.50 ±0.10 0.70 ±0.10 0.80 ±0.10 2.30 ±0.10 1 PAT1220 W2 1 0 W K b3 b2 b3 W3 a2 a1 a2 1: Electrode (surface soldering and lead-free possible) 2: Covering resin 3: Alumina substrate 4: Thin film resistor 5: Mark (shows impedance, attenuations and date) L a W1 a t Dimensions (mm) a1 b1 a1 L W b3 3.20 ±0.20 1.60 ±0.20 0.40 ±0.10 1.00 ±0.25 1.00 ±0.20 0.55 ±0.25 0.40 ±0.25 0.40 ±0.20 1.00 ±0.20 0.65 ±0.20 0.80 ±0.10 1.20 ±0.20 3.40 ±0.20 C01 W2 W 4 3 b2 t a b W1 W2 PAT1632 2 b W3 5 b b3 W3 b1 a2 W3 b2 b3 a1 a2 1: Electrode (surface soldering and lead-free possible) 2: Covering resin 3: Alumina substrate 4: Thin film resistor 5: Mark (shows impedance, attenuations and date) L t a1 b1 a1 Dimensions (mm) C (50W) b3 D (75W) 4.20 ±0.20 3.00 ±0.20 0.80 ±0.15 0.80 ±0.20 0.50 ±0.20 3.10 ±0.20 1.05 ±0.20 0.95 ±0.20 0.95 ±0.20 0.80 ±0.20 0.95 ±0.20 0.90 ±0.20 0.95 ±0.20 0.30 ±0.20 3.50 ±0.20 1.55 ±0.20 1.55 ±0.20 0.55 ±0.20 0.60 ±0.20 0.55 ±0.20 0.60 ±0.20 1.55 ±0.20 W1 Wa C07 2 5 a L W W 4 3 b2 t a b3 b Lb a2 C (50W) b1 b2 2.90 ±0.20 0.90 ±0.20 1.10 ±0.20 1.20 ±0.20 5.30 ±0.20 D (75W) 3.30 ±0.20 1.10 ±0.20 1.00 ±0.20 1.00 ±0.20 5.30 ±0.20 Wa Wb W1 W2 W3 W4 Wb PAT3042S W2 W3 Wb K a b Lb b W4 b3 a1 a2 1: Electrode (surface soldering and lead-free possible) 2: Covering resin 3: Alumina substrate 4: Thin film resistor 5: Mark (shows impedance, attenuations and date) © IRC Advanced Film Division • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com 38 PAT Series Issue October 2006 Sheet 2 of 3 High Frequency Surface Mount Attenuators Power Derating Curve % of Rated Power 100 IRC Advanced Film Division Schematic Diagram Data 1 2 60 0 25° Ambient Temperature (°C) Temperature in °C 70° 125° 3 3 3 1 2 Ordering Data Prefix Model PAT1220; PAT1632; PAT3042SD (75W); PAT3042SC(50W) HFR - PAT1220 - C - 3dB - T(5) 3 3 Attenuation 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 16, 20dB Impedence C = 50W; D = 75W Package T=Tape, B=Bulk, Taping Quantity Unit:5 (5000), 1 (1000) © IRC Advanced Film Division • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com 39 PAT Series Issue October 2006 Sheet 3 of 3