HFR-PAT3042SLF-D-16-B

High Frequency Surface Mount Attenuators PAT-S Series • RoHS compliant • Frequency operation up to 10GHz • Low parasitic capacitance and inductance • Thin film stability over time and temperature The PAT chip attenuator series is available in a wide range of power ratings from 32mW to 250mW. The surface mount package is ideal for applications where parasitic capacitance and inductance are concerns. Typical applications include wireless communication receivers and transmitters. Electrical Data PAT0510SLF Impedance Frequency Range Attenuation (dB) Attenuation Tolerance Power Rating TCR VSWR Operating Temperature Range 0 to 3dB ±0.3dB 4 to 7dB ±0.5dB 8 to 10dB ±1.0dB 32mW 64mW 50Ω PAT0816LF 50Ω DC to 10 GHz 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 0 to 10dB: ±0.3dB 16dB: ±0.5dB 125mW ±50ppm/°C 1.3 PAT1220LF 50Ω PAT1632LF 50Ω DC to 3GHz PAT3042SCLF 50Ω DC to 3GHz PAT3042SDLF 75Ω DC to 2GHz 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 16, 20 0 to 10dB: ±0.3dB 16, 20dB: ±0.5dB 250mW ±0.3dB 100mW -55°C to +125°C General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. © IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com A subsidiary of TT electronics plc PAT-S Series Issue February 2009 Sheet 1 of 3 High Frequency Surface Mount Attenuators Physical Data PAT0510SLF, PAT0816LF W2 W W3 2 1 t 1 2 W4 1 2 L 3 W3 4 3 4 3 (Top) 4 W4 (Bottom) (Side) PAT1220LF, PAT1632LF, PAT3042CLF W2 W t 1 1 3 W4 1 3 3 L 2 2 2 3 W4 3 (Bottom) (Top) (Side) Dimensions (mm) Model PAT1220LF PAT1632LF PAT3042SLF PAT0510SLF PAT0816LF L 2.0 ± 0.2 3.2 ± 0.2 4.2 ± 0.2 1.0 ± 0.05 1.60 ± 0.1 W 1.25 ± 0.2 1.6 ± 0.2 3.0 ± 0.2 0.5 ± 0.05 0.8 ± 0.1 L2 0.6 ± 0.2 1.0 ± 0.2 0.5 ± 0.2 0.27 ± 0.05 0.4 ± 0.15 W3 0.35 ± 0.2 0.4 ± 0.2 0.95 ± 0.2 0.12 ± 0.04 0.2 ± .015 t 0.4 ± 0.1 0.4 ± 0.1 0.8 ± 0.15 0.3 ± 0.05 0.4 ± 0.1 © IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com PAT-S Series Issue February 2009 Sheet 2 of 3 High Frequency Surface Mount Attenuators Environmental Data Test Condition Short Time Overload Load Life Moisture Resistance Temperature Cycle Resistance to Solder Heat Terminal Strength Solderability Insulation Resistance 2.5 x rated voltage, 5 sec 1000 Hours, 70°C 1000 Hours, 60°C, 95% RH 5 Cycles, 125°C High, -55°C Low 260°C, 10 sec. Fulcrum dist: 90mm, Bending width: 3mm Substrate: Glass epoxy t=1.6mm 235°C, 3 sec. 500V, 1 minute Tolerance Attenuation ±0.03dB ±0.05dB ±0.05dB ±0.03dB ±0.03dB ±0.03dB ∆ Impedance ±0.5% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% >95% coverage >1000MΩ Power Derating Curve 100 Ordering Data Prefix Model PAT0510SLF; PAT0816LF; PAT1220LF; PAT1632LF PAT3042SLF HFR - PAT1220LF - C - 3dB - T(5) % Of Rated Power 60 Impedence C = 50Ω; D = 75Ω Attenuation 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 16, 20dB 10 Package 25 70 125 T = Tape, B = Bulk, Taping Quantity Unit: 5 (5000), 1 (1000) Ambient Temperature (°C) © IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com PAT-S Series Issue February 2009 Sheet 3 of 3