OPB698AZ

OPB685      Photologic® output Four output options Mechanical switch replacement Printed circuit board mounting (OPB685 Series) 2.5mm, 3-pin connector mates with Molex connector 5051 series housing and 4809 series terminal for OPB695 Series OPB695 Each OPB685 and OPB695 series flag switch consists of an infrared emitting diode and a monolithic integrated circuit that incorporates a photodiode, a linear amplifier and a Schmitt trigger. A lever arm actuated flag interrupts the light beam, which switches the output between states that can readily drive logic gates. The OPB695 series is designed to easily snap mount into a 0.037” ± 0.001” (0.940 mm ± 0.025 mm) thick material with a rectangular opening of 0.320” ± 0.003” x 0.472” (8.13 mm x 11.99 mm) minimum. Insertion into the punched side of metal is recommended. Devices in these series feature TTL/LSTTL compatible logic level output that can drive up to 10 TTL loads over a voltage range from 4.5 V to 16 V. Customized lever arms and spring torques can be designed for specific applications for each of the devices. Custom electrical, wire, cabling and connectors are available. Contact your local representative or OPTEK for more information. Ordering Information  Mechanical switch replacement  Speed indication (tachometer)  Mechanical limit indication  Edge sensing Part Number LED Peak Wavelength Sensor Photologic® OPB685 10K Pull-Up OPB686 Open Collector OPB687 Inv. 10K Pull-Up OPB688 Inv. Open Collector Flag Travel Degrees Max Lead Length / Spacing or Connector 59° 0.100" / 0.275" OPB695AZ OPB695BZ 10K Pull-Up OPB695CZ OPB696AZ OPB696BZ 890 nm Open Collector OPB696CZ 70° OPB697AZ OPB697BZ Inv. 10K Pull-Up OPB697CZ OPB698AZ OPB698BZ RoHS OPB698CZ Inv. Open Collector Mates with 3 Pin—Molex 5051 (22-01-1032) Housing & 4809 (08-70-0069) Terminals OPB685, OPB685-3, OPB686, OPB687, OPB688 Pin # Description 1 Anode 5 Cathode 2 Ground 3 Output 4 VCC [ MILLIMETERS] DIMENSIONS ARE IN: INCHES OPB695, OPB696, OPB697, OPB698 Part Number Max. Torque (Grams) OPB685 1.5 Pin # OPB695 OPB685-3 3.0 1 VCC OPB686 1.5 2 Output OPB687 1.5 3 Ground OPB688 1.5 OPB695 1.5 OPB696 1.5 OPB697 1.5 OPB698 1.5 Torque is measured at the end of the arm from the resting position to the switching point of the flag Storage & Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] -40°C to +100°C (1) Reverse Voltage 260°C 2.0 V Continuous Forward Current 50 mA Peak Forward Current Total Device Power Dissipation 3.0 A (2) 100 mW ® Supply Voltage, VCC Duration of Output Short to VCC Voltage at Output Notes: (1) (2) (3) (4) 1 second 30 V Low Level Output Current (sinking) Power Dissipation 18 V (3) (4) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.33 mW/°C above 25° C. Derate linearly 2.00 mW/°C above 25° C (OPB680, OPB680-20, OPB690Z). Derate linearly 2.50 mW/°C above 25° C (OPB685, OPB686, OPB687, OPB688, OPB695, OPB696, OPB697, OPB698). 16 mA 240 mW OPB685 and OPB695 Series OPB685, OPB695 Buffered 10K Pull-Up OPB686, OPB696 Buffered Open-Collector OPB687, OPB697 Inverted 10K Pull-Up OPB688, OPB698 Inverted Open-Collector VF Forward Voltage - - 1.6 V IF = 10 mA IR Reverse Current - - 100 µA VR = 3 V 4.5 4.5 8.0 13.5 5.0 12.0 15.0 16.0 8.0 13.5 16.0 - 20 30 mA mA ® VCC Operating DC Supply Voltage OPB685 Series OPB695-698A OPB695-698B OPB695-698C ICC Operating DC Supply Voltage OPB695-698A/B/C ICCL Low Level Supply Current: Buffered 10k Pull-Up Buffered Open-Collector OPB685 OPB686 - 5.5 4.0 12 12 Inverted 10k Pull-Up Inverted Open-Collector OPB687 OPB688 - 6.5 5.0 12 12 mA VCC = 16 V, IF = 10 mA (no load on output) High Level Supply Current: Buffered 10k Pull-Up Buffered Open-Collector OPB685 OPB686 - 5.0 12 mA VCC = 16 V, IF = 10 mA (no load on output) Inverted 10k Pull-Up Inverted Open-Collector OPB687 OPB688 - 4.0 12 mA VCC = 16 V, IF = 0 mA (no load on output) OPB685 OPB686 OPB695 OPB696A/B/C - - 0.4 0.4 0.4 0.4 - - VCC -1.5 ICCH Low Level Output Voltage(1): Buffered 10k Pull-Up Buffered Open-Collector VOL Inverted 10k Pull-Up(2) VOH VCC = 16 V, IF = 0 mA (no load on output) V VCC = 4.5 V, IOL = 16 mA, IF = 0 VCC = 4.5 V to 8 V, IOL = 16 mA VCC = 8.5 V to 13 V, IOL = 16 mA VCC = 13.5 V to 16 V, IOL = 16 mA 0.4 0.4 0.4 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 0 VCC = 4.5 V to 8 V, IOL = 16 mA VCC = 8.5 V to 13 V, IOL = 16 mA VCC = 13.5 V to 16 V, IOL = 16 mA - - V IOH = 100 µA, IF = 10 mA VCC -1.5 - - V IOH = 100 µA, IF = 0 mA OPB686 OPB696A OPB696B OPB696C - - 100 100 100 100 OPB688 OPB698A OPB698B OPB698C - - 100 100 100 100 OPB685 OPB686 OPB695 OPB696A/B/C Inverted Open-Collector V High Level Output Voltage(2): Buffered 10k Pull-Up (1) Inverted 10k Pull-Up Inverted Open-Collector (2) High Level Output Voltage : Buffered Open-Collector IOH Inverted 10k Pull-Up(1) µA µA VCC = 16 V, IF = 10 mA, VCH = 30 V VCC = 4.5 V to 8 V, VOH = 30 V VCC = 8.5 V to 13 V, VOH = 30 V VCC = 13.5 V to 16 V, VOH = 30 V VCC = 16 V, IF = 10 mA, VCH = 30 V(1) VCC = 4.5 V to 8 V, VOH = 30 V(1) VCC = 8.5 V to 13 V, VOH = 30 V(1) VCC = 13.5 V to 16 V, VOH = 30 V(1) ® IF(+) IF(+)/IF(-) trtf tPLHtPHL LED Positive-Going Threshold Current OPB685-688 0.1 1.8 10 mA VCC = 5 V Hysteresis 1.0 1.2 1.6 mA VCC = 5 V Rise Time, Fall Time - 30 - ns Propagation Delay Low-High & High-Low: Buffer, 10k Pull-Up OPB685 Buffer, Open-Collector OPB686 - 1 (LH) 2 (HL) - µs µs Inverter, 10k Pull-Up Inverter, Open-Collector - 2 (LH) 1( HL) - OPB685/688 OPB687 OPB688 Notes: (1) Test requires lever arm in “blocked” position. (2) Test requires lever arm in “unblocked” position µs µs VCC = 5 V, IF = 0 or 10 mA RL = 300 Ω, DC = 50% f = 10 kHz