OPB706A

 Choice of Phototransistor (OPB706) or Photodarlington (OPB707) output  Unfocused for sensing diffuse surface  Low cost plastic housing  Designed for use with PCBoards or connectors The OPB706 consists of an infrared Light Emitting Diode (LED) and an NPN silicon Phototransistor mounted “side-by-side” on parallel axes in a black plastic housing. The OPB707 consists of an infrared LED and an NPN silicon Photodarlington mounted “side-by-side” on parallel axes in a black plastic housing. On both OPB706 and OPB707, the LED and Phototransistor / Photodarlington are molded using dark infrared transmissive plastic to reduce ambient light noise. The Phototransistor / Photodarlington responds to light from the emitter when a reflective object passes within its field of view of the device. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information.       Part Number Non-contact reflective object sensor Assembly line automation Machine automation Machine safety End of travel sensor Door sensor OPB706A OPB706B OPB706C OPB707A OPB707B OPB707C LED Peak Wavelength Sensor Reflection Distance Lead Length / Spacing 0.050" (1.27mm) 0.45" / 0.087", 0.100" Transistor 935 nm Darlington OPB706 3 1 4 2 OPB707 [ MILLIMETERS] DIMENSIONS ARE IN: RoHS 3 1 4 2 INCHES Pin # LED Pin # Transistor 3 4 Anode Cathode 1 2 Collector Emitter Storage and Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] -40° C to +85° C (1) 260° C Input Diode Forward DC Current 50 mA Peak Forward Current (1 µs pulse width, 300 pps) 3A Reverse DC Voltage 2V (2) 75 mW Power Dissipation Output Phototransistor (OPB706) | Output Photodarlington (OPB707) Collector-Emitter Voltage OPB706 OPB707 24 V 15 V Emitter-Collector Voltage 5V Collector DC Current OPB706 OPB707 Power Dissipation OPB706(2) OPB707(3) Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.25 mW/°C above 25 ° C. (3) Derate linearly 1.67 mW/°C above 25 ° C. 25 mA 125 mA 75 mW 100 mW Input Diode (see OP165W for additional information) VF Forward Voltage - - 1.7 V IF = 20 mA IR Reverse Current - - 100 μA VR = 2 V Output Phototransistor (see OP505W for additional information) | Photodarlington (see OP535 for additional information) V(BR)CEO Collector-Emitter Brealdown Voltage OPB706 OPB707 24 15 - - V IC = 100 µA V(BR)ECO Emitter-Collector Breakdown Voltage 5 - - V IE = 100 µA Collector Dark Current OPB706 OPB707 - - 100 250 nA VCE = 5 V, IF = 0, EE ≤ 0.1 µW/cm2 Crosstalk OPB706 OPB707 - - 200 10 nA µA IF = 20 mA, VCE = 5 V, No reflecting surface(1) On-State Collector Current OPB706A OPB706B OPB706C 500 350 250 - - OPB707A OPB707B OPB707C 25 17 10 - - ICEO Combined ICX IC(ON) VCE(SAT) Collector-Emitter Saturation Voltage OPB706 OPB707 0.4 1.1 - - µA IF = 20 mA, VCE = 5V , d = 0.05” (1.27 mm)(2) (3) mA V IF = 20 mA, d = 0.05” (1.27 mm)(2) (3) IC(ON) = 100µA IC(ON) = 2 mA Notes: (1) Crosstalk (ICX) is the collector current measured with the indicated current in the input diode and with no reflecting surface. (2) The distance from the assembly face to the reflective surface is “d”. (3) Measured using Eastman Kodak neutral white test card with 90% diffuse reflectance as a reflecting surface. Reference: Eastman Kodak, Catalog #E 152 7795. (4) Lower curve is a calculated worst case condition rather than the conventional -2 Ω limit. (5) All parameters tested using pulse techniques. OPB706 - Output Current vs Forward Current vs Temperature OPB706 - Normalized Collector Current vs. Object Distance 3.0 1.2 Normalized IF = at 20mA atV20°C, VCC = Normalized at IF = at 20mA 20ºC, CE=5V 5V = 0.050” (1.27mm) using Kodak 90% at Distance using Kodak 90% at Distance = 0.050" VCE = 5V, IF = 20mA, Normalized at 0.050" Kodak 90% 2.5 Normalized Output Current Normalized Output Current 1.0 0.8 Kodak 90% Kodak 19% Copy Paper Avery Retro Reflective 0.6 0.4 0.2 2.0 1.5 -40° C -20° C 0° C 20° C 40° C 60° C 80° C 1.0 0.5 0.0 0.0 0.0 0.2 0.4 0.6 0.8 1.0 0 5 10 15 Distance to Reflective Surface (inches) 20 25 30 35 40 45 50 Forward Current - mA OPB707 - Normalized Collector Current vs. Object Distance OPB707 - Output Current vs Forward Current vs Temperature 1.6 1.2 Normalized at at IIF 20mAatat20ºC, 20°C,VVCC = 5V Normalized 20mA F == CE=5V using usingKodak Kodak90% 90%atatDistance Distance= =0.050" 0.050”(1.27mm) (1.27mm) VCE = 5V, IF = 20mA, Normalized at 0.050" Kodak 90% 1.4 Normalized Output Current Normalized Output Current 1.0 0.8 Kodak 90% Kodak 18% Copy Paper Avery Retro Reflective 0.6 0.4 1.2 1.0 0.8 -40° C -20° C 0° C 20° C 40° C 60° C 80° C 0.6 0.4 0.2 0.2 0.0 0.0 0.0 0.2 0.4 0.6 0.8 Distance to Reflective Surface (inches) 1.0 0 5 10 15 20 25 30 35 Forward Current - mA 40 45 50