Photologic® Dual Channel Encoder
OPBA301, OPBA303
Features:
Dual channel outputs for Quadrature output
Open collector inverter outputs
0.010” (0.254 mm) sensor apertures for high resolution
Snap mount
Product Photo Here
Description:
The OPBA301 and OPBA303 device consists of an infrared emitting diode and a monolithic integrated circuit
which incorporates two independent photodiodes, linear amplifiers, Schmitt trigger circuits and output transistors.
The OPBA301 features a dual TTL output that is compatible with TTL/LSTTL and can drive 8 TTL loads. The
OPBA303 has a 10K Ω pull-up output with EMI protection on each channel.
Applications include linear and rotary encoders with high resolution provided by internal 0.010” (0.254 mm)
apertures located in front of the Photologic® sensor on 0.040” (1.02 mm) center line spacing.
Custom electrical design, wire length and connectors are available. Contact your local representative or OPTEK
for more information.
Applications:
Ordering Information
Mechanical switch replacement
Speed and direction indication
Mechanical limit indication
Rotary encoders
Edge sensing
Sliding door automotive and
Part
Number
LED Peak
Wavelength
OPBA301
Sensor
Output
Slot Width /
Depth
Aperture
Emitter/Sensor
Wire
Length
0.200" / 0.350”
0.05” / 0.01"
24”
22 AWG Flat
Dual TTL
890 nm
OPBA303
10K Pull-Up
liftgate applications
OPBA301
VREG
AMP
OPBA303
4-Vcc
4-Vcc
VREG
10K
3-Out B
AMP
3-Out B
0.01µf
AMP
2-Out A
AMP
1-GND
10K
2-Out A
0.01µf
1-GND
OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue B 02/13
Page 1 of 5
Photologic® Dual Channel Encoder
OPBA301, OPBA303
OPBA301, OPBA303
B
A
Pin #
Description
1
Output-A
2
Output-B
3
VCC
4
Ground
CONTAINS POLYSULFONE
To avoid stress cracking, we suggest using
ND Industries’ Vibra-Tite for thread-locking.
Vibra-Tite evaporates fast without causing
structural failure in OPTEK’s molded plastics.
Absolute Maximum Ratings (TA = 25° C unless otherwise noted)
Storage & Operating Temperature Range
-40°C to +85° C
Input Diode
Forward DC Current
50 mA
Reverse DC Voltage
2.0 V
(1)
100 mW
Supply Voltage, VCC
5.5 V
Voltage at Output
OPBA301
OPBA303
18 V
5.5V
Power Dissipation
Output Photologic®
Power Dissipation(2)
200 mW
Sinking Output Current
DIMENSIONS ARE IN:
40 mA
[ MILLIMETERS]
INCHES
OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures.
Issue B 02/13
Page 2 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic® Dual Channel Encoder
OPBA301, OPBA303
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
4.5
-
5.5
V
TEST CONDITIONS
Input Diode
Supply Voltage
VCC
Output Photologic® Sensor
ICCL
Supply Current
Both Outputs Low
(both photodiodes irradiated)
-
25.5
29
mA
Unblocked condition (no load on output)
ICCH
Supply Current
Both Outputs High
(both photodiodes shaded)
-
20.5
23
mA
Blocked condition (no load on output)
ICCM
Supply Current
Mixed Output States
(one high, one low)
-
23
-
mA
1 blocked condition
1 unblocked condition
IOH
High Level Output Current
-
1
30
µA
VOH = 16 V (blocked condition)
VOL
Low Level Output Voltage
-
0.21
0.40
V
IOL = 12.8 mA (unblocked condition)
Propagation Delay
Output High to Low
Output Low to High
-
2
10
-
µs
µs
VCC = 5 V, RL = 360 Ω,
f = 10 kHz, DC = 50%
Output Rise Time
Output Fall Time
-
20
5
-
ns
ns
RL = 360 Ω
tPHL, tPLH
tr, tf
Performance Curves
Low Level Output vs Ambient Temperature
High Level Output vs Ambient Temperature
33
VCC = 4.5 V
IOL = 12.8 mA
λ = 890 nm
EE = 0.5 mW/cm2
Low Level Output Current - V
OL
0.4
15
10
5
VCC = 5 V
No Load on Output
λ = 890 nm
31
Supply C urrent - I CC L , I CC H (m A)
(volts)
mW/cm2
20
OH
(nA)
VCC = 4.5 V
VOH = 18 V
EE = 0
High Level Output Current - I
Supply Current vs Ambient Temperature
0.5
25
0.3
VOL
0.2
29
27
25
ICCL
23
ICCH
21
0.1
19
IOH
17
0
0
0
-50
-25
0
25
50
TA - Ambient Temperature (°C)
75
100
-50
-25
0
25
50
75
100
TA - Ambient Temperature (°C)
-50
-25
0
25
50
75
100
TA - Ambient Temperature (°C)
OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue B 02/13
Page 3 of 5
Photologic® Dual Channel Encoder
OPBA301, OPBA303
Performance Curves
Rise and Fall Time vs Ambient Temperature
vs Output Load
Propagation Delay vs Ambient Temperature
20
250
VCC = 5 V
λ = 890 nm
f = 10 kHz
t r, R L = 2 K Ώ
Propagation Delay - t P H L , t P LH (µs)
Switching Tim e - t r, t f (ns)
200
Amplitude = 0.5 mW/cm2
VCC = 5 V
RL = 360 Ώ
λ = 890 nm
f = 10 kHz
Duty Cycle = 50%
150
Amplitude = 0.5 mW/cm2
t r, R L = 1 K Ώ
100
50
15
10
tPHL
5
tPLH
tr, RL = 360 Ώ
tf, RL = 360 Ώ, 1 k Ώ, 2 kΏ
0
-50
-25
0
25
50
75
0
100
-50
-25
TA - Ambient Temperature (°C)
0
25
50
75
100
TA - Ambient Temperature (°C)
Ideal Target Size & Spacing
For Linear or Circular Targets
Sensor Output(s)
Ch-A
0.09 [2.20]
Clear
Hole
Ch-B
0.09 [2.20]
Clear
Hole
0.07 [1.80]
Clear
Hole
0.07 [1.80]
0.06 [1.50] MIN.
0.07 [1.80]
1-1
0-1
0-0
1-0
1-1
0-1
0-0
1-0
Dimensions are in inches [mm]
Please consult OPTEK for target design and
sensor location relative to the target.
OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures.
Issue B 02/13
Page 4 of 5
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Photologic® Dual Channel Encoder
OPBA301, OPBA303
Issue
Approval
Date
Initial Release
Tom Osborne
2/03/06
A.1
Minor changes to the first paragraph on page 1
Tom Osborne
3/29/06
A.2
Changed part numbers OPBA301 & OPBA302 on page 2
Tom Osborne
4/10/06
A.3
Added new DIMENSIONS statement and repositioned items on the
pages to match other data sheets. Used smaller new logo. Fixed
minor typos on page 2.
A.4
Removed OPBA300, OPBA302, changed verbiage to accommodate
the change, removed Package 1.
A
Change Description
07/28/06
Tom Osborne
02/21/2013
OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue B 02/13
Page 5 of 5
很抱歉,暂时无法提供与“OPBA303”相匹配的价格&库存,您可以联系我们找货
免费人工找货