OVFSG6C8

4-Pin Green LED Lamp (7.6 mm) OVFSG6C8 x x x x x Packaged in tubes Compatible with automatic placement equipment Compatible with infrared and vapor phase reflow solder process Mono-color type Pb-free Product Photo Here The OVFSG6C8 is designed with higher forward voltage to maximize brightness and incorporates a low-profile lens to enhance efficient light distribution. Response time is fast and it consumes less power resulting in low current requirements from circuit power supply. Tubular arrays replace neon in outdoor and indoor signs. This square package allows high-density arrays to form light engines. Applications x Automotive: Rear stop/turn signal lamps/truck marker lamps x Mood-setting decoration and landscape lighting x Special decorative interior/exterior lighting x Special effects stage lighting x Illumination for signs and channel letters x Traffic signals, pedestrian and walkway signs RoHS Part Number Material Emitted Color Flux Typ. mlm Lens Color OVFSG6C8 InGaN Green 2500 Water Clear Moisture DIMENSIONS ARE IN INCHES AND [MILLIMETERS]. 2,3 ANODE 1,4 CATHODE DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com Issue A 04/06 Page 1 of 4 4-Pin Green LED Lamp OVFSG6C8 Absolute Maximum Ratings TA = 25o C unless otherwise noted Storage Temperature Range -40 ~ +100° C Operating Temperature Range -40 ~ +100° C Lead Soldering Temperature (3 mm from the base of the epoxy bulb) 1 260° C Reverse Voltage 5V Continuous Forward Current 2 30 mA Peak Forward Current (10% Duty Cycle, PW ”—VHF 100 mA Power Dissipation 140 mW Notes: 1. Solder time less than 3 seconds at temperature extreme. Electrical Characteristics TA = 25o C unless otherwise noted PARAMETER MIN TYP MAX UNITS CONDITIONS lumen Luminous Flux 1500 2500 ---- mlm IF = 30 mA VF Forward Voltage ---- 4.0 4.6 V IF = 30 mA IR Reverse Current ---- ---- 100 µA VR = 5 V Dominant Wavelength 515 527 535 nm IF = 30 mA 50% Power Angle ---- 60 ---- deg IF = 30 mA SYMBOL D 2 ½ Luminous Flux (mlm) Standard Bins (IF = 30 mA) Lamps are sorted to luminous flux ( V), forward voltage (VF), and dominant wavelength ( D) bins shown. Orders for OVFSG6C8 may be filled with any or all bins contained as below. X6 X7 X8 X9 2500-3600 H 2000-3000 G 1500-2400 F 515 520 525 530 535 Luminous flux is at F bin or above. Dominant Wavelength (nm) Forward Voltage (VF) Rank V9 V10 V11 V12 V13 V14 V15 Voltage (V) 3.2–3.4 3.4–3.6 3.6–3.8 3.8–4.0 4.0–4.2 4.2–4.4 4.4–4.6 Important Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. To designate luminous intensity ranks, please contact OPTEK. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 04/06 Page 2 of 4 Phone: (972) 323-2200 or (800) 341-4747 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com 4-Pin Green LED Lamp OVFSG6C8 Typical Electro-Optical Characteristics Curves mA % mA V Forward Current vs Forward Voltage Half Power Relative Luminous Flux vs Forward Current WL = 38 nm mA °C nm Relative Luminous Flux vs Wavelength Maximum Forward DC Current vs Ambient Temperature 50% Power Angle: 60° V A Far Field Pattern Reverse Current vs Reverse Voltage OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com Issue A 04/06 Page 3 of 4 4-Pin Green LED Lamp OVFSG6C8 Moisture Resistant Packaging 60/Tube Aluminum Moisture-proof Bag Desiccant Bar Code Label OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A 04/06 Page 4 of 4 Phone: (972) 323-2200 or (800) 341-4747 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com