OVM4RTXV

Hi-Reliability Visible LED Lamp (TO46) OVM4x, OVM4xTX, OVM4xTXV • • • • Hermetically sealed TO-46 package Choice of blue, green, red or yellow High-brightness with well-defined spatial radiation patterns ESD protection built in Product Photo Here Each OVM4x, OVM4xTX and OVM4xTXV device is a high-reliability, high-sensitivity visible LED that is mounted in a hermetically sealed TO-46 package. “Hi-Reliability” Visible LEDs function in the abnormally severe levels of mechanical, environmental and electrical stress that are typical of military and harsh industrial applications. OVM4xTX and OVM4xTXV devices are processed to OPTEK’s 100% screening and QCI program-patterned after MIL-PRF-19500. Group A and B are performed on every lot. Group C is performed every six months. Applications • Automotive exterior and interior lighting • Architectural lighting • Electronic signs and signals Blue Intensity Typ. (mcd) 2260 Clear Glass InGaN Green 6520 Clear Glass OVM4RTXV AlInGaP Red 3300 Clear Glass OVM4YTXV AlInGaP Yellow 2010 Clear Glass Part Number Part Number Material Emitted Color OVM4BTX OVM4BTXV InGaN OVM4GTX OVM4GTXV OVM4RTX OVM4YTX ANODE (BRAZED) CATHODE (ISOLATED) Pin 2 Pin 1 RoHS Lens Color Pin 1 Cathode Pin 2 Anode Dimensions are in inches [ mm] DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.4 05/10 Page 1 of 4 Hi-Reliability Visible LED Lamp OVM4x, OVM4xTX, OVM4xTXV Absolute Maximum Ratings TA = 25o C unless otherwise noted Storage Temperature Range -65° C to +150° C Operating Temperature Range -55° C to +100° C Reverse Voltage 5V Continuous Forward Current 2 100 mA Peak Forward Current (10% Duty Cycle, 1 KHz) 1.6 A Power Dissipation 370 mW Lead Soldering Temperature (3mm from the case)1 260° C Current Linearity vs. Ambient Temperature -0.2 mA/° C LED Junction Temperature 115° C Notes: 1. Solder time less than 5 seconds at temperature extreme. 2. Design of heat dissipation should be considered. Electrical Characteristics TA = 25o C unless otherwise noted SYMBOL Iv VF λP λD Δλ 2Θ½ PARAMETER Luminous Intensity Forward Voltage Peak Wavelength Dominant Wavelength Spectral Half Width 50% Power Angle MIN TYP MAX Blue ---- 2260 ---- Green ---- 6520 ---- Red ---- 3300 ---- Yellow ---- 2010 ---- Blue ---- 2.60 2.95 Green ---- 2.60 2.95 Red ---- 1.80 2.15 Yellow ---- 1.80 2.15 Blue ---- 463 ---- Green ---- 530 ---- Red ---- 630 ---- Yellow ---- 591 ---- Blue 460 465 470 Green 520 530 540 Red 619 624 629 Yellow 584 589 594 Blue ---- 22 ---- Green ---- 35 ---- Red ---- 15 ---- Yellow ---- 18 ---- ---- 18 ---- UNITS CONDITIONS mcd IF = 20 mA V IF = 20 mA nm IF = 20 mA nm IF = 20 mA nm IF = 20 mA deg IF = 20 mA Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. To designate luminous intensity ranks, please contact OPTEK. 3. Pb content