OVSARGB3R8

Full Color PLCC4 LED OVSARGB3R8 x x x x x x Surface mount device packaged in 8mm tape on 7” diameter reel Compatible with automatic placement equipment Compatible with infrared and vapor phase reflow solder Pb-free, RoHS-compliant Dimensions: 3.5x2.8x1.9mm 120° viewing angle Product Photo Here The OVSARGB3R8 provides full color light output from a single package, 3-die design. This surface mount package is an efficient solution in modular applications that require uniform brightness and color-on-demand. Light output is optimized by an interior reflector and the wide viewing angle adds flexibility for applications ranging from hand-held appliances to automotive interiors. Applications x RGB+White Full-color Indoor and Outdoor Displays x Backlighting x Coupling into Lightguides x Automotive Interiors x Entertainment Equipment Part Number OVSARGB3R8 Type R G B Material AlInGaP InGaN InGaN Chip Emitted Color Red Green Blue Intensity Typ. mcd 300 450 110 Lens Color Water Clear RoHS 1,3,4 CATHODE 2 ANODE DIMENSIONS ARE IN INCHES AND [MILLIMETERS]. Data is subject to change without prior notice. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue 1.0 0605 Page 1 Full-Color PLCC4 LED OVSARGB3R8 Absolute Maximum Ratings TA = 25o C unless otherwise noted RATING PARAMETER R G UNIT B Storage Temperature -40 ~ +100 °C Operating Temperature -40 ~ +100 °C 5 V Reverse Voltage Continuous Forward Current 1 50 25 25 mA Peak Forward Current (10% Duty Cycle, PW ” sec) 200 100 100 mA Power Dissipation 130 105 105 mW 110 110 110 °C Junction/ambient (1 chip on ) 450 400 450 °C/W Junction/ambient (3 chips on2) 650 580 680 °C/W Junction/solder point (1 chip on) 300 280 300 °C/W Junction/solder point (3 chips on) 450 430 480 °C/W Junction Temperature 2 Notes: 1. Single color light 2. Rth test condition: Mounted on PC Board FR 4 (pad size 
 2 ) Electrical Characteristics TA = 25o C unless otherwise noted SYMBOL PARAMETER IV Luminous Intensity VF Forward Voltage IR VALUES UNIT CONDITIONS mcd IF = 20mA V IF = 20mA 10 µA VR = 5V 520–540 460–480 nm IF = 20mA 620 520 465 nm IF = 20mA 50% Power Angle 120 120 120 deg IF = 20mA Spectrum Radiation Bandwidth 24 38 28 nm IF = 20mA R G B Min 180 280 71 Typ 300 450 110 Typ 2.3 3.6 3.6 Max 2.6 4.2 4.2 Reverse Current (max) 10 10 D Dominant Wavelength 612–625 P Wavelength at Peak Emission 2 Issue 1.0 Page 2 ½ 0605 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Full-Color PLCC4 LED OVSARGB3R8 Standard Bins (IF=20mA) Lamps are sorted to luminous intensity (IV) and dominant wavelength ( D) bins shown. Orders for OVSARGB3R8 may be filled with any or all bins contained as below. Luminous Intensity (mcd) RED 450 280 T 180 S 612 Dominant Wavelength (nm) Luminous intensity is at S bin or above. 625 Luminous Intensity (mcd) GREEN 710 450 U 280 T 520 Dominant Wavelength (nm) Luminous intensity is at T bin or above. 540 Luminous Intensity (mcd) BLUE 180 112 R 71 Q 460 Dominant Wavelength (nm) Luminous intensity is at Q bin or above. 480 Important Notes: 1. All ranks will be included per delivery, rank ratio will be based on the chip distribution. 2. Tolerance of measurement of luminous intensity is ±10%. 3. Tolerance of measurement of dominant wavelength is ±1nm. 4. Tolerance of measurement of VF is ±0.05V. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue 1.0 0605 Page 3 Full-Color PLCC4 LED OVSARGB3R8 Typical Electro-Optical Characteristics Curves Relative Intensity vs. Dominant Wave Length IF(mA) IF(mA) Forward Current vs. Forward Voltage VF(V) Percent (%) Percent (%) VF(V) IF(mA) IF(mA) Relative Luminous Intensity vs. Forward Current Issue 1.0 Page 4 0605 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Full-Color PLCC4 LED OVSARGB3R8 Typical Electro-Optical Characteristics Curves 1 Chip On 3 Chips On IF(mA) IF(mA) TA(°C) TA(°C) Maximum Forward DC Current vs. Solder Point Temperature 1 Chip On 3 Chips On IF(mA) IF(mA) TA(°C) TA(°C) Maximum Forward DC Current vs. Ambient Temperature 50% Power Angle: 120° Far Field Pattern OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue 1.0 0605 Page 5 Full-Color PLCC4 LED OVSARGB3R8 CIE Graph The color coordinates of the mixed light can be expected within the area of the color triangle marked a). The achromatic point (x =0.33, y=0.33) is marked “+”. Issue 1.0 Page 6 0605 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Full-Color PLCC4 LED OVSARGB3R8 Reel Dimensions (7 Inch) Carrier Tape Dimensions: Loaded Quantity 2000 PCS per Reel Moisture Resistant Packaging Label Aluminum Moisture-proof Bag OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Desiccant Bar Code Label Issue 1.0 0605 Page 7 Full-Color PLCC4 LED OVSARGB3R8 Issue 1.0 Issue 1.0 Page 8 0605 Change Description Initial Release Approval Date J. Haynie 6/30/05 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com