PPS11001000J

Metal Glaze™ Power Pack Surface Mount High Power Density Ceramic Package PPS-1 Series • • • • • • Low inductance 0.1Ω to 348KΩ range Superior surge handling capability 150°C maximum operating temperature 1 Watt performance - standard 2010 footprint Flameproof ceramic package provides superior temperature rise profile Electrical Data Size IRC Type PPS-1 Maximum Power Rating 1W Working Voltage¹ 350 Maximum Voltage 700 Resistance Range (ohms) 0.1 to 0.99 1.0 to 348K Tolerance (±%)² 1, 2, 5 1, 2, 5 TCR (ppm/°C)² 100 50, 100 2010 ¹Not to exceed ( √ P x R )½. ²Consult factory for tighter tolerances and TCRs. Applications The PPS-1 will dissipate 1 watt at 70°C on a 2010 footprint. The PPS-1 is recommended for applications where board real estate or component/board TCE mismatch is a major concern. It is also recommended in circuits where a standard 2010 resistor exhibits marginal or unacceptable performance due to high power density/surge handling demands. Environmental Data Characteristic Thermal Shock Low Temperature Operation Short Time Overload High Temperature Exposure Resistance to Bonding Exposure Solderability Moisture Resistance Life Test Terminal Adhesion Strength Resistance to Board Bending Maximum Change ±(0.5% + 0.01 ohm) ±(0.25% + 0.01 ohm) ±(1.0% + 0.01 ohm) ±(0.5% + 0.01 ohm) ±(0.25% + 0.01 ohm) 95% minimum coverage ±(0.5% + 0.01 ohm) ±(1.0% + 0.01 ohm) ±(1% + 0.01 ohm) ±(1% + 0.01 ohm) Test Method MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles) MIL-R-55342E Par 4.7.4 (-65°C @ working voltage) MIL-R-55342E Par 4.7.5 (2.5 x (PxR)½ MIL-R-55342E Par 4.7.6 (+150°C for 100 hours) MIL-R-55342E Par 4.7.7 (Reflow soldered to board @ 260°C for 10 seconds) MIL-STD-202, Method 208 (245°C for 5 seconds) MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours) MIL-R-55342E Par 4.7.10 (2000 hours @ 70°C intermittent) 1200 gram push from underside of mounted chip for 60 seconds Chip mounted in center of 90mm long board, deflected 5mm so as to exert pull on chip contacts for 10 seconds General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com A subsidiary of TT electronics plc PPS-1 Series Issue December 2008 Sheet 1 of 2 Metal Glaze™ Power Pack Surface Mount High Power Density Ceramic Package Physical Data (Inches and (mm)) Top View: 0.170 ± 0.010 (4.32 ± 0.25) 0.130 ± 0.005 (3.30 ± 0.13) 0.079 ± 0.006 (2.01 ± 0.15) 0.200 ± 0.010 (5.08 ± 0.25) Side View: 0.105 ± 0.005 (2.67 ± 0.13) 0.130 ± 0.005 (3.30 ± 0.13) Ordering Data Sample Part No. IRC Type (PPS1) PPS1 100 1000 F Temperature Coefficient Resistance Value Tolerance F = 1%, G = 2%, J = 5% Wire and Film Technologies Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com PPS-1 Series Issue December 2008 Sheet 2 of 2