RC-RC65LFC6K8CA

Precision Metal Film Resistor RC Series • Resistance tolerance down to ±0.05% • Low noise and negligible voltage coefficient • CECC released product with low TCRs over a wide resistance range • 100% tin plated (Pb-free, RoHS compliant) leads Electrical Data RC55 Commercial Power Rating At 70°C Resistance Range Limiting Element Voltage Isolation Voltage TCR (20 to +70°C) & codes Resistance Tolerance Approved CECC 40101-004 Power Rating At 70°C Resistance Range Limiting Element Voltage Isolation Voltage TCR & Codes Resistance Tolerance (code) Approved CECC 40101-804 Power Rating At 70°C Resistance Range Limiting Element Voltage Isolation Voltage TCR & Codes Resistance Tolerance (code) Standard Values Thermal Impedance Ambient Temperature Range °C/Watt °C 110 Watts Ohms Volts Volts ppm/°C % Watts Ohms Volts Volts ppm/°C % A 0.125 1R to 1M 200 280 Watts Ohms Volts Volts ppm/°C % H 0.063 1R to 1M 200 280 0.25 1R to 4M 350 500 0.5 1R to 4M 350 500 5(V), 10(T), 15(Y), 25(D), 50(C) & 100(Z) 0.05(W), 0.1(B), 0.25(C), 0.5(D) & 1 (F) J 0.125 1R to 1M 200 280 K 0.25 1R to 1M 250 350 K 0.25 10R to 1M 250 350 L 0.5 10R to 1M 350 500 See resistance restrictions C 0.5 10R to 1M 350 500 See resistance restrictions Any value to order 1.0 1R to 10M 500 700 See resistance restrictions RC65 RC70 Notes 15(Y), 25(D), 50(C) & 100(Z) 0.05(W), 0.1(B), 0.25(C), 0.5(D) & 1(F) B 0.25 1R to 1M 250 350 B 0.25 10R to 1M 250 350 15(T), 25(E) & 50(C) 0.05(W), 0.1(B), 0.25(C), 0.5(D) & 1(F) E24, E96 Preferred 70 -55 to +155 60 General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC’s own data and is considered accurate at time of going to print. © IRC Advanced Film Division • 4222 South Staples Street • Corpus Christi Texas 78411 USA Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com A subsidiary of TT electronics plc RC Series Issue December 2008 Sheet 1 of 3 Precision Metal Film Resistor Physical Data Dimensions (mm) & Weight (g) Type RC55 RC65 RC70 L Max 7.2 10.0 15.5 D F Max Min 2.5 3.7 5.5 30 30 30 D Nom 0.6 0.6 0.8 PCB Mounting Centers 10.2 12.7 18.4 Min Bend Radius 0.6 0.6 1.2 Wt. Nom 0.24 0.40 1.15 d D L f Construction A metal film is deposited onto a high quality ceramic former. Nickel-plated steel caps are force fitted to the former and termination wires are welded to the caps. The resistor is adjusted to value by a helical cut in the film and the body is protected with a specially formulated epoxy coating. Marking Type reference, TCR code, resistance value and tolerance code. The resistance values conform to IEC 62. Solvent Resistance The body protection and marking are resistant to all normal industrial cleaning solvents suitable for printed circuits. Terminations Material Strength Solderability 100% tin plated over copper wire The teminations meet the requirements of IEC 68.2.21. The terminations meet the requirements of IEC 115-1, Clause 4.17.3.2. Environmental Data CECC 40101-004 Requirements Load At Commercial Rating: 1000 Hours At 70°C Load At CECC Rating: 1000 Hours At 70°C Dry Heat: 1000 Hours at 155°C Shelf Life: 12 Months at Room Temperature Derating From Rated Power At 70°C Short Term Overload Climatic Climatic Category Long Term Damp Heat Temperature Rapid Change Resistance To Solder Heat Vibration and Bump Noise (in a decade of frequency) Voltage Coefficient Of Resistance Note: CECC 40101-804 Requirements --0.5 0.5 Not specified 50% at 125°C 0.1 0.5 55/155/56 0.5 0.1 0.1 0.1 Not specified Not specified *Actual Performance Maximum 0.3 0.3 **1.0 0.1 --0.1 0.3 55/155/56 0.5 **0.2 0.06 0.06 1.0 --Typical 0.1 0.05 0.15 0.03 --0.02 0.1 --0.1 0.05 0.03 0.02 0.1