105PF40T

Bulletin I2028 rev. D 01/05 105PF40T STANDARD RECOVERY DIODES (Lead-Free) Stud Version Features High surge current capability Very low VF 105 A Major Ratings and Characteristics Parameters IF(AV) @ TC IF(RMS) IFSM @ 50Hz @ 60Hz I2t @ 50Hz @ 60Hz VRRM TJ range range 105PF 105 150 160 2300 2400 23900 26450 400 - 40 to 180 Units A °C A A A A2 s A2 s V °C case style DO-203AB (DO-5) www.irf.com 1 105PF40T Final I2028 rev. D 01/05 ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage VRRM, maximum repetitive peak reverse voltage V 400 VRSM, maximum nonrepetitive peak reverse voltage V 500 IRRM max. @ TJ = 150°C Type number 105PF Code mA 5 40 Forward Conduction Parameter I F(AV) Max. average forward current @ Case temperature 105PF 105 150 150 135 Units Conditions A °C A °C A t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms A2s t = 8.3ms t = 10ms t = 8.3ms No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max. 180° conduction, half sine wave I F(RMS) Max. RMS forward current I FSM Max. peak, one-cycle forward, non-repetitive surge current 160 2300 2400 1970 2050 I 2t Maximum I2t for fusing 26450 23900 19400 17440 I 2√ t V F(TO) rf VFM Maximum I2√t for fusing Value of threshold voltage Value of forward slope resistance Max. forward voltage drop 200 0.75 kA2√s t = 0.1 to 10ms, no voltage reapplied V TJ = TJ max. TJ = TJ max. VIpk= 200A, TJ = 25°C, tp = 400µs rectangular wave 1.0 1.05 mΩ V Thermal and Mechanical Specifications Parameter TJ Tstg RthJC RthCS T Max. junction operating temperature range Max. storage temperature range Max. thermal resistance, junction to case Max. thermal resistance, case to heatsink Allowable mounting torque (1) As general recommendation we suggest to tight on hexagon and not on nut 105PF -40 to 180 -40 to 180 0.25 0.25 2.8 25 3.4 +0-10% 30 Units Conditions °C °C/W AC operation Mounting surface, smooth, flat and greased Top thread; using bus-bar or plate, only. Avoid silicone grease on thread Bottom base; tighting on nut (1) Not lubricated threads Bottom base; tighting on hexagon (2) Lubricated threads unleaded device See Outline Table Nm lbf · in Nm lbf · in Nm lbf · in g (oz) (2) Torque must be appliable only to hexagon and not to plastic structure 2.3 +0-10% 20 17 (0.6) DO-203AB (DO5) wt Approximate weight Case style 2 www.irf.com 105PF40T Bulletin I2028 rev. D 01/05 Maximum Allowable Case Temperature (°C) 105PF Series Maximum Allowable Case Temperature (°C) 180 180 105PF Series 170 160 150 140 130 120 110 100 0 50 100 150 200 250 Average Forward Current (A) Fig. 2 - Current Ratings Characteristics 160 Conduction Angle Conduction Period 30˚ 60˚ 90˚ 120˚ 180˚ DC 30˚ 140 60˚ 90˚ 120˚ 180˚ 120 0 20 40 60 80 100 120 140 160 Average Forward Current (A) Fig. 1 - Current Ratings Characteristics Maximum Allowable Case Temperature (°C) Maximum Allowable Case Temperature (°C) 180 160 140 120 100 80 60 40 20 0 0 180˚ 120˚ 90˚ 60˚ 30˚ 250 200 150 DC 180˚ 120˚ 90˚ 60˚ 30˚ RMS Limit 100 RMS Limit 50 0 0 50 100 150 200 250 Average Forward Current (A) Fig. 4 - Current Ratings Characteristics Conduction Angle 150PF Series Conduction Period 105PF Series 40 80 120 160 Average Forward Current (A) Fig. 3 - Current Ratings Characteristics Peak Half Sine Wave Forward Current (A) Peak Half Sine Wave Forward Current (A) 2200 2000 1800 1600 1400 1200 1000 800 600 400 1 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge. Initial Tj = Tj Max. @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 2500 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Initial Tj = Tj Max. 2000 No Voltage Reapplied Rated Vrrm Reapplied 1500 1000 500 105PF Series 105PF Series 10 100 0 0.01 Number Of Equal Amplitude Half Cycle Current Pulses (N) Pulse Train Duration (s) 0.1 1 10 Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current www.irf.com 3 105PF40T Final I2028 rev. D 01/05 1000 Instantaneous Forward Current (A) Transient Impedance Z thJC (K/W) 1 Tj = Tj Max. Steady State Value RthJC = 0.25 K/W (DC Operation) 100 Tj = 25˚C 0.1 10 105PF Series 0.01 85HF(R) Series 1 0.6 0.8 1 1.2 1.4 1.6 0.001 0.0001 0.001 0.01 0.1 1 10 Instantaneous Forward Voltage (V) Fig. 7 - Forward Voltage Drop Characteristics Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Outline Table 105PF Case Style DO-203AB (DO-5) All dimensions in millimeters (inches) 4 www.irf.com 105PF40T Bulletin I2028 rev. D 01/05 Ordering Information Table Device Code 105 1 PF 2 40 3 T 4 1 2 3 4 - Current Rating (105 = 105A) PF = Plastic Package Voltage Rating (40 = 400V) T = Top Thread Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level and Lead-Free. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 2 33 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 01/05 www.irf.com 5