180RKI80

Bulletin I25153 rev. D 09/03 180/181RKI SERIES PHASE CONTROL THYRISTORS Stud Version Features Hermetic glass-metal seal International standard case TO-209AB (TO-93) 180A Typical Applications DC motor controls Controlled DC power supplies AC controllers Major Ratings and Characteristics Parameters IT(AV) @ TC IT(RMS) ITSM @ 50Hz @ 60Hz I 2t @ 50Hz @ 60Hz V DRM /V RRM tq TJ typical 180/181RKI 180 80 285 3800 4000 72 66 400 to 1000 100 - 40 to 125 Units A °C A A A KA2s KA2s V µs °C case style TO-209AB (TO-93) www.irf.com 1 1 80/181RKI Series Bulletin I25153 rev. D 09/03 ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage Type number Code 40 180/181RKI 80 100 V DRM /V RRM , max. repetitive peak and off-state voltage V 400 800 1000 repetitive peak voltage V 500 900 1100 VRSM , maximum non- I DRM /I RRM m ax. @ TJ = TJ max. mA 30 On-state Conduction Parameter I T(AV) Max. average on-state current @ Case temperature I T(RMS) Max. RMS on-state current I TSM Max. peak, one-cycle non-repetitive surge current 180/181RKI 180 80 285 3800 4000 3500 3660 Units Conditions A °C DC @ 79°C case temperature t = 10ms A t = 8.3ms t = 10ms t = 8.3ms t = 10ms KA2 s t = 8.3ms t = 10ms t = 8.3ms KA √s 2 180° conduction, half sine wave No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max. I 2t Maximum I2t for fusing 72 66 61 56 I √t 2 Maximum I √t for fusing 2 720 0.83 t = 0.1 to 10ms, no voltage reapplied (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. V T(TO)1 Low level value of threshold voltage V T(TO) 2 High level value of threshold voltage r t1 r t2 V TM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Typical latching current V 0.89 (I > π x IT(AV)),TJ = TJ max. (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max. mΩ 0.81 1.35 600 1000 V mA (I > π x IT(AV)),TJ = TJ max. Ipk= 570A, TJ = TJ max, tp = 10ms sine pulse TJ = 25°C, anode supply 12V resistive load 0.92 Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current td tq Typical delay time Typical turn-off time 180/181RKI 300 1.0 Units Conditions A/µs Gate drive 20V, 20Ω, tr ≤ 1µs TJ = TJ max, anode voltage ≤ 80% VDRM Gate current 1A, di g /dt = 1A/µs Vd = 0.67% VDRM, TJ = 25°C µs 100 ITM = 50A, TJ = TJ max, di/dt = 1 0A/µs, V R = 1 00V dv/dt = 2 0V/µs 2 www.irf.com 1 80/181RKI Series Bulletin I25153 rev. D 09/03 Blocking Parameter dv/dt IRRM IDRM Maximum critical rate of rise of off-state voltage Max. peak reverse and off-state leakage current 180/181RKI 500 30 Units Conditions V/µs mA TJ = TJ max. linear to 80% rated VDRM TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM IGM +VGM -VGM Maximum peak gate power Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. IGT DC gate current required to trigger 130 65 35 VGT DC gate voltage required to trigger 2.0 1.2 0.9 IGD VGD DC gate current not to trigger DC gate voltage not to trigger 10 0.25 PG(AV) Maximum average gate power 180/181RKI 10 2.0 3.0 20 Units Conditions W A TJ = TJ max, t p ≤ 5 ms TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t p ≤ 5 ms V 5.0 MAX. 150 2.5 mA V V mA TJ = TJ max., tp ≤ 5ms TJ = - 40°C TJ = 25°C TJ = 125°C TJ = - 40°C TJ = 25°C TJ = 125°C TJ = TJ max. Max. gate current/ voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied Thermal and Mechanical Specification Parameter TJ Tstg Max. operating temperature range Max. storage temperature range 180/181RKI -40 to 125 -40 to 150 0.15 Units Conditions °C RthJC Max. thermal resistance, junction to case RthCS Max. thermal resistance, case to heatsink T Mounting torque, ± 10% DC operation K/W Mounting surface, smooth, flat and greased 0.04 31 (275) 24.5 (210) Nm (lbf-in) Non lubricated threads Lubricated threads g See Outline Table wt Approximate weight Case style 280 TO - 209AB (TO-93) www.irf.com 3 1 80/181RKI Series Bulletin I25153 rev. D 09/03 ∆RthJC Conduction Conduction angle 180° 120° 90° 60° 30° (The following table shows the increment of thermal resistence RthJC when devices operate at different conduction angles than DC) Sinusoidal conduction Rectangular conduction Units 0.050 0.063 0.080 0.118 0.225 0.032 0.059 0.082 0.124 0.228 K/W Conditions T J = T J m ax. Ordering Information Table Device Code 18 1 2 3 4 IT(AV) rated average output current (rounded/10) 0 = Eyelet terminals (Gate and Auxiliary Cathode Leads) 1 = Fast - on terminals (Gate and Auxiliary Cathode Leads) Thyristor Voltage code: Code x 10 = VRRM (See Voltage Rating Table) 1 1 2 RKI 100 3 4 Outline Table GLASS METAL SEAL 19 (0.75) MAX. 8.5 (0.33) DIA. 4.3 (0.17) DIA. 9. 5( 0.3 6) 7) MI M N. IN . 4 (0.16) MAX. FLEXIBLE LEAD C.S. 25mm 2 RED SILICON RUBBER 10 (0.39) RED CATHODE C.S. 0.4mm (0.0006 s.i.) WHITE GATE 2 (0.039 s.i.) +I 210 (8.26) Case Style TO-209AB (TO-93) All dimensions in millimeters (inches) 82 (3.23) MIN. RED SHRINK 220 (8.66) +10 (0.39) WHITE SHRINK Fast-on Terminals 28.5 (1.12) 16 (0.63) MAX. MAX. 28.5 (1.12) MAX. DIA. 21 (0.83) MAX. SW 32 3/4"-16UNF-2A 35 (1.38) MAX. 4 22 AMP. 280000-1 REF-250 (0 .8 www.irf.com 1 80/181RKI Series Bulletin I25153 rev. D 09/03 Maximum Allowable Case Temperature (°C) 130 120 110 Conduction Angle Maximum Allowable Case Temperature (°C) 180/181RKI Series 181RKI Series R thJC (DC) = 0.15 K/W 130 120 110 180/181RKI Series 181RKI Series R thJC (DC) = 0.15 K/W Conduction Period 100 90 80 70 0 20 40 60 80 100 120 140 160 180 20 0 Average On-state Current (A) Fig. 1 - Current Ratings Characteristics 100 90 80 70 0 50 100 150 200 250 300 Average On-state Current (A) Fig. 2 - Current Ratings Characteristics 30° 60° 90° 30° 60° 90° 120° 180° 120° 180° DC Maximum Average On-state Power Loss (W) 240 SA R th 220 200 180 160 140 180° 120° 90° 60° 30° RMS Limit 2K 0. 3 0. W K/ 0.6 K/ W /W K/ W .1 =0 elt -D aR 120 100 80 60 0 .8 1K K/W /W Conduction Angle 1 .5 K/W 40 20 0 180/181RKI Series 181RKI Series T J = 125°C 2 K/W 0 20 40 60 80 100 120 140 160 180 0 25 50 75 100 125 Average On-state Current (A) Maximum Allowable Ambient Temperature (°C) Fig. 3 - On-state Power Loss Characteristics Maximum Average On-state Power Loss (W) 350 300 250 200 DC 180° 120° 90° 60° 30° A hS Rt 0. 2 K/ = W 1 0. 0. 3 W K/ K/ W el -D ta R 150 RMS Limit Conduction Period 0.6 K/ W 100 50 0 0 50 100 180/181RKI Series 181RKI Series T J = 125°C 150 200 250 K/ W 1 K/ W 1.5 K /W 2 K/ W 0.8 0 300 25 50 75 100 125 Average On-state Current (A) Maximum Allowable Ambient Temperature (°C) Fig. 4 - On-state Power Loss Characteristics www.irf.com 5 1 80/181RKI Series Bulletin I25153 rev. D 09/03 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) 4000 3500 At Any Rated Load Condition And With Rated VRRM Applied Following Surge. Initial TJ = 125°C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 4000 3000 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. 3500 Initial TJ = 125°C No Voltage Reapplied Rated VRRM Reapplied 3000 2500 2500 2000 180/181RKI Series 181RKI Series 2000 180/181RKI Series 181RKI Series 1500 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) 1500 0.01 0.1 Pulse Train Duration (s) 1 Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current 10000 Instantaneous On-state Current (A) TJ = 25°C 1000 TJ = 125°C 180/181RKI Series 181RKI Series 100 0.5 1 1.5 2 2.5 3 Instantaneous On-state Voltage (V) Fig. 7 - On-state Voltage Drop Characteristics Transient Thermal Impedance Z thJC (K/W) 1 Steady State Value R thJC = 0.15 K/W (DC Operation) 0.1 0.01 180/181RKI Series 181RKI Series 0.001 0.001 0.01 0.1 Square Wave Pulse Duration (s) 1 10 Fig. 8 - Thermal Impedance Z thJC Characteristic 6 www.irf.com 1 80/181RKI Series Bulletin I25153 rev. D 09/03 100 Instantaneous Gate Voltage (V) Rectangular gate pulse a) Recommended load line for rated di/dt: 20V, 30ohms; tr6µs b) Recommended load line for 10