20CTQ150TRLPBF

Bulletin PD-20648 rev. C 09/04 20CTQ150 20CTQ150S 20CTQ150-1 SCHOTTKY RECTIFIER 20 Amp Major Ratings and Characteristics Characteristics IF(AV) Rectangular waveform VRRM IFSM @ tp = 5 µs sine VF TJ @ 10 Apk, TJ = 125°C (per leg) range Description/ Features Units A V A V This center tap Schottky ectifier has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 175° C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. 175° C TJ operation Center tap configuration Low forward voltage drop High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance High frequency operation Guard ring for enhanced ruggedness and long term reliability Values 20 150 1030 0.66 - 55 to 175 °C Case Styles 20CTQ150 20CTQ150S 20CTQ150-1 Base Common Cathode 2 Base Common Cathode 2 Base Common Cathode 2 1 Anode 2 Common Cathode 3 1 Anode Anode 2 Common Cathode 3 1 Anode Anode 2 Common Cathode 3 Anode TO-220AB D2PAK TO-262 www.irf.com 1 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 Voltage Ratings Parameters VR Max. DC Reverse Voltage (V) VRWM Max. Working Peak Reverse Voltage (V) 20CTQ150 20CTQ150S 20CTQ150-1 150 Absolute Maximum Ratings Parameters IF(AV) Max. Average Forward Current IFSM EAS IAR * See Fig. 5 (Per Leg) (Per Device) Values 10 20 1030 180 2.45 0.7 Units A Conditions 50% duty cycle @ TC = 154°C, rectangular wave form 5µs Sine or 3µs Rect. pulse Following any rated load condition and with 10ms Sine or 6ms Rect. pulse rated V RRM a pplied TJ = 25 °C, IAS = 0.7 Amps, L = 10 mH Current decaying linearly to zero in 1 µsec Frequency limited by TJ max. VA = 1.5 x VR typical Max. Peak One Cycle Non-Repetitive Surge Current (Per Leg) * See Fig. 7 Non-Repetitive Avalanche Energy (Per Leg) Repetitive Avalanche Current (Per Leg) A mJ A Electrical Specifications Parameters VFM Max. Forward Voltage Drop (Per Leg) * See Fig. 1 (1) Typ. 0.80 0.90 0.63 0.73 Max. Units 0.88 1.0 0.66 0.77 25 5.0 280 8.0 10000 V V V V µA mA pF nH V/ µs Conditions @ 10A @ 20A @ 10A @ 20A TJ = 25 °C TJ = 125 °C @ 25°C TJ = 25 °C TJ = 125 °C VR = rated VR IRM CT LS Max. Reverse Leakage Current (Per Leg) * See Fig. 2 Typical Junction Capacitance (Per Leg) Typical Series Inductance (Per Leg) 3.0 2.7 - VR = 5VDC (test signal range 100kHz to 1Mhz) Measured lead to lead 5mm from package body (Rated VR) (1) Pulse Width < 300µs, Duty Cycle < 2% dv/dt Max. Voltage Rate of Change Thermal-Mechanical Specifications Parameters TJ Tstg Max. Junction Temperature Range Max. Storage Temperature Range Values -55 to 175 -55 to 175 2.0 1.0 0.50 2 (0.07) Min. Max. 6 (5) 12 (10) Units °C °C Conditions RthJC Max. Thermal Resistance Junction to Case (Per Leg) RthJC Max. Thermal Resistance Junction to Case (Per Package) RthCS Typical Thermal Resistance, Case to Heatsink wt T Approximate Weight Mounting Torque Marking Device °C/W DC operation °C/W DC operation °C/W Mounting surface , smooth and greased (only for TO-220) g (oz.) Kg-cm (Ibf-in) Case style TO-220 Case style D2-Pak Case style TO-262 20CTQ150 20CTQ150S 20CTQ150-1 2 www.irf.com 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 100 Reverse Current - I R (mA) 100 10 1 0.1 0.01 Tj = 175˚C 150˚C 125˚C 100˚C 75˚C 50˚C 25˚C Instantaneous Forward Current - I F (A) 0.001 0.0001 0 20 40 60 80 100 120 140 160 Reverse Voltage - VR (V) Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) 10 1000 T J = 175˚C T J = 125˚C T J = 25˚C Junction Capacitance - C T (p F) Tj = 25˚C 100 1 0.2 0.4 0.6 0.8 10 1 1.2 1.4 1.6 1.8 2 0 40 80 120 160 Forward Voltage Drop - V FM (V) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg) Reverse Voltage - VR (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg) 10 (°C/W) 1 Thermal Impedance Z D = 0.75 D = 0.50 D = 0.33 D = 0.25 D = 0.20 Notes: thJC P DM t1 t2 0.1 Single Pulse (Thermal Resistance) 1. Duty factor D = t1/ t2 2. Peak Tj = Pdm x ZthJC + Tc 0.01 0.00001 0.0001 0.001 0.01 t1 , Rectangular Pulse Duration (Seconds) 0.1 1 Fig. 4 - Max. Thermal Impedance ZthJC Characteristics (Per Leg) www.irf.com 3 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 180 Allowable Lead Temperature (°C) Allowable Power Loss (Watts) 10 9 8 7 6 5 4 3 2 1 0 0 170 DC D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 DC RMS Limit 160 150 Square wave (D = 0.50) 80% Rated Vr applied 140 see note (2) 130 0 2 4 6 8 10 12 14 16 Average Forward Current - I F(AV) (A) Fig. 5 - Maximum Average Forward Current Vs. Allowable Lead Temperature Non-Repetitive Surge Current - I FSM (A) 3 6 9 12 15 Average Forward Current - I F(AV) (A) Fig. 6 - Maximum Average Forward Dissipation Vs. Average Forward Current 1000 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge 100 10 100 1000 10000 Square Wave Pulse Duration - t p (microsec) Fig. 7 - Maximum Peak Surge Forward Current Vs. Pulse Duration L HIGH-S PEED S CH WIT FREE-WHEEL DIODE 40HF L40S 02 + DUT IR FP460 R = 25 ohm g Vd = 25 Volt CURR ENT MONIT OR Fig. 8 - Unclamped Inductive Test Circuit (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 80% rated VR 4 www.irf.com 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 Outline Table 10.54 (0.41) MAX. 3.78 (0.15) 3.54 (0.14) 15.24 (0.60) 14.84 (0.58) 123 14.09 (0.55) 13.47 (0.53) 3.96 (0.16) 3.55 (0.14) 2.04 (0.080) MAX. 1.40 (0.05) 1.15 (0.04) 0.94 (0.04) 0.69 (0.03) 2.89 (0.11) 2.64 (0.10) 0.10 (0.004) Base Common Cathode 2 1.32 (0.05) DIA. 6.48 (0.25) 6.23 (0.24) 2° 1.22 (0.05) 2.92 (0.11) 2.54 (0.10) TERM 2 123 4.57 (0.18) 4.32 (0.17) 0.61 (0.02) MAX. 1 Anode 2 Common Cathode 3 Anode 5.08 (0.20) REF. Conform to JEDEC outline TO-220AB Dimensions in millimeters and (inches) Modified JEDEC outline TO-262 Dimensions in millimeters and (inches) Base Common Cathode 2 1 Anode 2 Common Cathode 3 Anode www.irf.com 5 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 Outline Table Base Common Cathode 2 1 Anode 2 Common Cathode 3 Anode Conform to JEDEC outline D2Pak (SMD-220) Dimensions in millimeters and (inches) Tape & Reel Information TRR 1.60 (0.063) 1.50 (0.059) 4.10 (0.161) 3.90 (0.153) FEED DIRECTION 1.60 (0.063) 1.50 (0.059) DIA. 0.368 (0.0145) 0.342 (0.0135) 1.85 (0.073) 1.65 (0.065) 11.60 (0.457) 11.40 (0.449) 15.42 (0.609) 15.22 (0.601) 1.75 (0.069) 24.30 (0.957) 23.90 (0.941) TRL 10.90 (0.429) 10.70 (0.421) 1.25 (0.049) 16.10 (0.634) 15.90 (0.626) DIA. 4.72 (0.186) 4.52 (0.178) FEED DIRECTION 13.50 (0.532) 12.80 (0.504) DIA. 26.40 (1.039) 24.40 (0.961) SMD-220 Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples 60 (2.362) DIA. MIN . 360 (14.173) DIA. MAX. of 800 pieces per reel for both TRL and TRR. Dimensions in millimeters and (inches) 6 www.irf.com 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 Part Marking Information EXAMPLE: THIS IS A 20CTQ150 LOT CODE 1789 ASSEMBLED ON WW 19, 2000 IN THE ASSEMBLY LINE "C" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE YEAR 0 = 2000 WEEK 19 LINE C TO-220 THIS IS A 20CTQ150S LOT CODE 8024 ASSEMBLED ON WW 02, 2000 IN THE ASSEMBLY LINE "L" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER 20CTQ150S DATE CODE YEAR 0 = 2000 WEEK 02 LINE L D2PAK PART NUMBER EXAMPLE: THIS IS A 20CTQ150-1 LOT CODE 1789 ASSEMBLED ON WW 19, 1999 IN THE ASSEMBLY LINE "C" INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE DATE CODE YEAR 9 = 1999 WEEK 19 LINE C TO-262 www.irf.com 7 20CTQ150, 20CTQ150S, 20CTQ150-1 Bulletin PD-20648 rev. C 09/04 Ordering Information Table Device Code 20 1 C 2 T 3 Q 4 150 5 S 6 TRL 7 8 1 2 3 4 5 6 - Current Rating (20 = 20A) C = Common Cathode T = TO-220 Q = Schottky Q Series Voltage Rating (150 = 150V) none = TO-220AB -1 S = TO-262 = D2Pak 7 - none = Tube (50 pieces) TRL = Tape & Reel (Left Oriented - for D 2Pak only) TRR = Tape & Reel (Right Oriented - for D 2Pak only) 8 - none = Standard Production PbF = Lead-Free Data and specifications subject to change without notice. This product has been designed for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 2 33 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 09/04 8 www.irf.com