70TPS16

Bulletin I2164 rev. A 10/04 SAFEIR Series 70TPS.. PHASE CONTROL SCR VT < 1.4V @ 100A ITSM = 1400A VRRM = 1200, 1600V Description/ Features The 70TPS... SAFEIR series of silicon controlled rectifiers are specifically designed for high and medium power switching and phase control applications. Typical applications are in input rectification (soft start) or AC-Switches or high current crow-bar as well as others phase-control circuits. These products are designed to be used with International Rectifier input diodes, switches and output rectifiers which are available in identical package outlines. Major Ratings and Characteristics Characteristics IT(AV) Sinusoidal waveform IRMS (*) 75 1200, 1600 1400 @ 100 A, TJ = 25°C 1.4 500 150 - 40 to 125 A V A V V/µs A/µs °C Package Outline Units A 70TPS.. 70 VRRM/ VDRM Range ITSM VT dv/dt di/dt TJ (*) Lead current limitation Super-247 www.irf.com 1 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Voltage Ratings Part Number VRRM/ VDRM, max. repetitive peak and off-state voltage V 70TPS12 70TPS16 1200 1600 VRSM , maximum non repetitive peak reverse voltage V 1300 1700 IRRM/ IDRM 125°C mA 15 Absolute Maximum Ratings Parameters IT(AV) Max. Average On-state Current IT(RMS) Max. Continuous RMS On-state Current As AC switch ITSM I2t Max. Peak One Cycle Non-Repetitive Surge Current Max. I 2t for Fusing 1200 1400 7200 10200 I √t 2 70TPS.. 70 75 Units A Conditions @ TC = 82° C, 180° conduction half sine wave Lead current limitation A A2s 10ms Sine pulse, rated VRRM applied 10ms Sine pulse, no voltage reapplied 10ms Sine pulse, rated VRRM applied 10ms Sine pulse, no voltage reapplied Initial TJ = TJ max. Max. I √t for Fusing 2 102000 0.916 A √s V 2 t = 0.1 to 10ms, no voltage reapplied TJ = 125°C VT(TO)1 Low Level Value of Threshold Voltage VT(TO)2 High Level Value of Threshold Voltage rt1 rt2 VTM di/dt IH IL IRRM / IDRM dv/dt Low Level Value of On-state Slope Resistance High Level Value of On-state Slope Resistance Max. Peak On-state Voltage Max. Rate of Rise of Turned-on Current Max. Holding Current Max. Latching Current Max. Reverse and Direct Leakage Current Max. Rate of Rise 1.21 4.138 mΩ 3.43 1.4 150 200 400 1.0 15 500 V A/µs mA @ 100A, TJ = 25°C TJ = 25°C TJ = 25°C mA TJ = 25°C TJ = 125°C VR = rated V RRM/ VDRM V/µs TJ = 125°C 2 www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Triggering Parameters PGM Max. peak Gate Power PG(AV) Max. average Gate Power IGM Max. peak Gate Current 70TPS.. 10 2.5 2.5 10 4.0 1.5 1.1 Units W t = 30µs Conditions A V TJ = - 40°C TJ = 25°C TJ = 125°C mA TJ = - 40°C TJ = 25°C TJ = 125°C V mA TJ = 125°C, V DRM = rated value Anode supply = 6V resistive load - V GM Max. peak negative Gate Voltage VGT Max. required DC Gate Voltage to trigger IGT Max. required DC Gate Current to trigger 270 100 80 V GD IGD Max. DC Gate Voltage not to trigger Max. DC Gate Current not to trigger 0.25 6 Thermal-Mechanical Specifications Parameters TJ Tstg Max. Junction Temperature Range Max. Storage Temperature Range 70TPS.. - 40 to 125 - 40 to 150 0.27 Units °C Conditions RthJC Max. Thermal Resistance Junction to Case RthJA Max. Thermal Resistance Junction to Ambient RthCS Max. Thermal Resistance Case to Heatsink wt T Approximate Weight Mounting Torque Min. Max. Case Style °C/W DC operation 40 0.2 Mounting surface, smooth and greased 6 (0.21) 6 (5) 12 (10) g (oz.) Kg-cm (lbf-in) Super-247 ∆R Conduction (per Junction) (The following table shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC) Device 70TPS Sine half wave conduction 180o 0.078 120o 0.092 90o 0.117 60o 0.172 30o 0.302 180 o 0.053 Rect. wave conduction 120 o 0.092 90o 0.125 60o 0.180 30o 0.306 Units °C/W www.irf.com 3 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Maximum Allowable Case temperature (°C) Maximum Allowable Case temperature (°C) 130 120 110 70TPS.. Series RthJC (DC) = 0.27 ˚C/W 130 120 110 70TPS.. Series RthJC (DC) = 0.27 ˚C/W DC Conduction Period Conduction Angle 100 180˚ 100 90 80 70 0 30˚ 60˚ 90˚ 120˚ 180˚ 90 80 30˚ 60˚ 70 60 0 90˚ 120˚ 10 20 30 40 50 60 70 80 Average On-state Current (A) Fig. 1 - Current Rating Characteristics 10 20 30 40 50 60 70 80 90 Average On-state Current (A) Fig. 2 - Current Rating Characteristics Maximum Average On-state Power Loss (W) Maximum Average On-state Power Loss (W) 140 120 100 80 60 40 20 0 0 180˚ 120˚ 90˚ 60˚ 30˚ RMS Limit 150 120 90 60 30 0 0 15 30 45 60 75 Average On-state Current (A) Fig. 4 - On-state Power Loss Characteristics 180˚ 120˚ 90˚ 60˚ 30˚ RMS Limit DC Conduction Angle 70TPS.. Series Tj = 125˚C Conduction Period 70TPS.. Series Tj = 125˚C 10 20 30 40 50 60 70 Average On-state Current (A) Fig. 3 - On-state Power Loss Characteristics Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) 1300 1200 1100 1000 900 800 700 600 500 1 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge. Initial Tj = 125˚C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 1500 1400 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. 1300 Initial Tj = 125˚C No Voltage Reapplied 1200 Rated Vrrm Reapplied 1100 1000 900 800 700 600 70TPS.. Series 70TPS.. Series 10 100 500 0.01 0.1 Pulse Train Duration (s) 1 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current 4 www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 1000 Instantaneous On-state Current (A) Tj = 125˚C 100 10 Tj = 25˚C 70TPS.. Series 1 0.5 1 1.5 2 2.5 3 3.5 Instantaneous On-state Voltage (A) Fig. 7 - On-state Voltage Drop Characteristics 100 Instantaneous Gate Voltage (V) 10 Rectangular gate pulse a)Recommended load line for rated di/dt: 20 V, 30 ohms tr = 0.5 µs, tp >= 6 µs b)Recommended load line for = 6 µs (1) PGM = 100 W, tp = 500 µs (2) PGM = 50 W, tp = 1 ms (3) PGM = 20 W, tp = 25 ms (4) PGM = 10 W, tp = 5 ms (a) (b) TJ = -40 ˚C TJ = 25 ˚C TJ = 125 ˚C 1 VGD IGD (4) (3) (2) (1) 0.1 0.001 70TPS.. Series Frequency Limited by PG(AV) 0.01 0.1 1 10 Instantaneous Gate Current (A) Fig. 8 - GateCharacteristics 100 1000 Transient Thermal Impedance Z thJC (°C/W) 1 Steady State Value (DC Operation) 0.1 D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Single Pulse 70TPS.. Series 0.01 0.0001 0.001 0.01 0.1 Square Wave Pulse Duration (s) 1 10 Fig. 9 - Thermal Impedance ZthJC Characteristics www.irf.com 5 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Outline Table 0.13 [.005] 16.10 [.632] 15.10 [.595] A 5.50 [.216] 4.50 [.178] 0.25 [.010] BA 2X R 2.15 [.084] 1.45 [.058] 13.90 [.547] 13.30 [.524] 1.30 [.051] 0.70 [.028] 20.80 [.818] 19.80 [.780] 4 16.10 [.633] 15.50 [.611] 4 C 1 2 3 B 14.80 [.582] 13.80 [.544] Ø 1.60 [.063] MAX. E E 4.25 [.167] 3.85 [.152] 5.45 [.215] 2X 3X 0.25 [.010] BA 3X 1.30 [.051] 1.10 [.044] 2.35 [.092] 1.65 [.065] SECTION E-E NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. 2. DIMENSIONS ARE SHOWN IN MILLIMETERS [INCHES] 3. CONTROLLING DIMENSION: MILLIMETER 4. OUTLINE CONFORMS TO JEDEC OUTLINE TO-274AA LEAD ASSIGNMENTS MOSFET 1 - GATE 2 - DRAIN 3 - SOURCE 4 - DRAIN IGBT 1 - GATE 2 - COLLECTOR 3 - EMITTER 4 - COLLECTOR Dimensions in millimeters and inches NOTE:parts are designed for clip mounting to heatsinks; mounting requirements and methods are discussed in AN-997 Ordering Information Table Device Code 70 1 T 2 P 3 S 4 16 5 2 (A) 1 2 3 4 5 - Current Rating Circuit Configuration: T = Thyristor Package: P = Super-247 Type of Silicon: S = Standard Recovery Rectifier Voltage code: Code x 100 = VRRM 12 = 1200V 16 = 1600V 1 (K) (G) 3 6 www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Data and specifications subject to change without notice. This product has been designed for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 2 33 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 10/04 www.irf.com 7