AUIPS71411G

February, 21st 2010 Automotive grade AUIPS71411G CURRENT SENSE HIGH SIDE SWITCH Features           Suitable 24V battery operation Over current shutdown Over temperature shutdown Current sensing Active clamp Low current ESD protection Optimized Turn On/Off for EMI Solenoid 24V loads for trucks Product Summary Rds(on) 100m max. Vclamp 65V Current shutdown 5A min. Applications Packages Description The AUIPS71411G is a fully protected four terminal high side switch specifically designed for 24V battery application. It features current sensing, over-current, overtemperature, ESD protection and drain to source active clamp. When the input voltage Vcc - Vin is higher than the specified threshold, the output power Mosfet is turned on. When the Vcc - Vin is lower than the specified Vil threshold, the output Mosfet is turned off. The Ifb pin is used for current sensing. SO8 Typical Connection Vcc IN Ifb Current feeback Input On Off IPS Battery Out 10k 1.5k Logic Ground Power Ground Load www.irf.com 1 AUIPS71411G Qualification Information† Qualification Level Automotive (per AEC-Q100††) Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. MSL2, 260°C (per IPC/JEDEC J-STD-020) Class M2 (200 V) (per AEC-Q100-003) Class H1C (1500 V) (per AEC-Q100-002) Class C5 (1000 V) (per AEC-Q100-011) ClassII, Level A (per AEC-Q100-004) Yes Moisture Sensitivity Level SOIC-8L Machine Model ESD Human Body Model Charged Device Model IC Latch-Up Test RoHS Compliant † †† Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ Exceptions to AEC-Q100 requirements are noted in the qualification report. www.irf.com 2 AUIPS71411G Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to the ground lead. (Tambient=25°C unless otherwise specified). Symbol Vout Vcc-Vin max. Iifb, max. Vcc sc. Pd Tj max. Parameter Maximum output voltage Maximum Vcc voltage Maximum feedback current Maximum Vcc voltage with short circuit protection see page 6 Maximum power dissipation (internally limited by thermal protection) Rth=100°C/W Max. storage & operating junction temperature Min. Max. Units V V mA V W °C Vcc-60 Vcc+0.3 -16 65 -50 10  50  -40 1.25 150 Thermal Characteristics Symbol Rth1 Parameter Thermal resistance junction to ambient SO8 Typ. 100 Max.  Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Iout RIfb Parameter Continuous output current, Tambient=85°C, Tj=125°C Rth=100°C/W Ifb resistor Min.  Max. 1.5  Units A k 1.5 www.irf.com 3 AUIPS71411G Static Electrical Characteristics Tj=25°C, Vcc=28V (unless otherwise specified) Symbol Vcc op. Rds(on) Parameter Min. Typ. Max. Units V m µA mA Test Conditions Ids=2A Vin=Vcc / Vifb=Vgnd Vout=Vgnd Vcc-Vin=28V Id=10mA Id=6A see fig. 2 Id=10mA If=1A Operating voltage 6 60   ON state resistance Tj=25°C 75 100  ON state resistance Tj=150°C(2) 135 180  Icc off Supply leakage current 1 3  Iout off Output leakage current 1 3 I in on Input current while on 0.6 1.6 3  V clamp1 Vcc to Vout clamp voltage 1 60 64 V clamp2 Vcc to Vout clamp voltage 2 60 65 72  Vih(1) High level Input threshold voltage 3 4.5  Vil(1) Low level Input threshold voltage 1.5 2.3  Forward body diode voltage Tj=25°C 0.8 0.9  Forward body diode voltage Tj=125°C 0.65 0.75 (1) Input thresholds are measured directly between the input pin and the tab. V Switching Electrical Characteristics Vcc=28V, Resistive load=27, Tj=25°C Symbol Tdon Tr Tdoff Tf Parameter Turn on delay time to 20% Rise time from 20% to 80% of Vcc Turn off delay time Fall time from 80% to 20% of Vcc Min. 4 2 20 2.5 Typ. 10 5 40 5 Max. 20 10 80 10 Units µs Test Conditions See fig. 1 µs Protection Characteristics Symbol Tsd Isd I fault Parameter Over temperature threshold Over-current shutdown Ifb after an over-current or an overtemperature (latched) Min. 150(2) 5 2.7 Typ. 165 7 3.3 Max.  Units °C A mA Test Conditions See fig. 3 and fig. 11 See fig. 3 and page 6 See fig. 3 10 4 Current Sensing Characteristics Symbol Parameter Min. 2000 -5% -0.2 0 Typ. 2400 0 0 8 Max. 2800 +5 0.2 100 Units % A µA Test Conditions Iload=2A Tj=-40°C to +150°C Iout 7A 100 Diag + Tj > 165°C IN IFB OUT 5 www.irf.com AUIPS71411G Truth Table Op. Conditions Normal mode Normal mode Open load Open load Short circuit to GND Short circuit to GND Over temperature Over temperature Input H L H L H L H L Output L H L H L L L L Ifb pin voltage 0V I load x Rfb / Ratio 0V 0V 0V V fault (latched) 0V V fault (latched) Operating voltage Maximum Vcc voltage : this is the maximum voltage before the breakdown of the IC process. Operating voltage : This is the Vcc range in which the functionality of the part is guaranteed. The Q100 qualification is run at the maximum operating voltage specified in the datasheet. Reverse battery During the reverse battery the Mosfet is kept off and the load current is flowing into the body diode of the power Mosfet. Power dissipation in the IPS : P = I load * Vf If the power dissipation is too high in Rifb, a diode in serial can be added to block the current. The transistor used to pull-down the input should be a bipolar in order to block the reverse current. The 100ohm input resistor can not sustain continuously 16V (see Vcc-Vin max. in the Absolute Maximum Ratings section) Active clamp The purpose of the active clamp is to limit the voltage across the MOSFET to a value below the body diode break down voltage to reduce the amount of stress on the device during switching. The temperature increase during active clamp can be estimated as follows:  Tj  PCL  Z TH ( t CLAMP ) Where: Z TH ( t CLAMP ) is the thermal impedance at tCLAMP and can be read from the thermal impedance curves given in the data sheets. PCL  VCL  ICLavg : Power dissipation during active clamp VCL  65V : Typical VCLAMP value. ICLavg  ICL : Average current during active clamp 2 t CL  di  dt ICL : Active clamp duration di dt VBattery  VCL : Demagnetization current L Figure 9 gives the maximum inductance versus the load current in the worst case : the part switch off after an over temperature detection. If the load inductance exceed the curve, a free wheeling diode is required. Over-current protection The threshold of the over-current protection is set in order to guaranteed that the device is able to turn on a load with an inrush current lower than the minimum of Isd. Nevertheless for high current and high temperature the device may switch off for a lower current due to the over-temperature protection (see Figure 11). www.irf.com 6 AUIPS71411G Current sensing accuracy Ifb Ifb2 Ifb1 Ifb leakage I offset Iout1 Iout2 Iout The current sensing is specified by measuring 3 points : - Ifb1 for Iout1 - Ifb2 for Iout2 - Ifb leakage for Iout=0 Then the parameters of the datasheet are computed by the following formula : Ratio = ( Iout2 – Iout1 )/( Ifb2 – Ifb1) I offset = Ifb1 x Ratio – Iout1 This allows the designer to evaluate the Ifb for any Iout value using : Ifb = ( Iout + I offset ) / Ratio if Ifb > Ifb leakage For some applications, a calibration is required. In that case, the accuracy of the system will depends on the variation of the I offset and the ratio over the temperature range. The ratio variation is given by Ratio_TC specified in page 3. The Ioffset variation depends directly of the Rdson : I offset@-40°C= I offset@25°C / 0.8 I offset@150°C= I offset@25°C / 1.9 Maximum Vcc voltage with short circuit protection The maximum Vcc voltage with short circuit is the maximum voltage for which the part is able to protect itself under test conditions representative of the application. 2 kind of short circuits are considered : terminal and load short circuit. L supply 5µH R supply 10mohm Vcc IPS Out L SC R SC Terminal SC Load SC L SC 0.1 µH 10 µH R SC 10 mohm 100 mohm www.irf.com 7 AUIPS71411G T clamp Vcc-Vin 80% Vcc-Vin 20% Ids 80% Vcc Vout 20% Td on Tr Td off Tf Vds Vds clamp See Application Notes to evaluate power dissipation Figure 1 – IN rise time & switching definitions Figure 2 – Active clamp waveforms 10 Vin Ids I shutdown Icc off, supply leakage current (µA) 8 6 4 Tj Tsd 165°C V fault Tshutdown 2 Vifb 0 -50 0 50 100 150 Tj, junction temperature (°C) Figure 3 – Protection timing diagram Figure 4 – Icc off (µA) Vs Tj (°C) www.irf.com 8 AUIPS71411G 20 4 Icc, supply current (mA) 1 5 3 Vih and Vil (V) 1 0 2 VIH 1 5 VIL 0 0 1 0 20 30 40 50 0 -50 -25 0 25 50 75 100 125 150 Vcc-Vin, supply voltage (V) Figure 5 – Icc (mA) Vs Vcc-Vin (V) Tj, junction temperature (°C) Figure 6 – Vih and Vil (V) Vs Tj (°C) 200% 100.00 Rds(on), Drain-to-Source On Resistance (Normalized) 150% Zth, transient thermal impedance (°C/W) 10.00 1.00 100% 0.10 50% -50 0 50 100 150 0.01 1.E05 1.E04 1.E03 1.E02 1.E- 1.E+0 1.E+0 1.E+0 01 0 1 2 Tj, junction temperature (°C) Figure 7 - Normalized Rds(on) (%) Vs Tj (°C) Time (s) Figure 8 – Transient thermal impedance (°C/W) Vs time (s) www.irf.com 9 AUIPS71411G 100 1.4 Ifb, current feedback current (mA) 1.2 25°C 1.0 0.8 Max. output current (A) 10 150°C 0.6 0.4 0.2 0.0 0 1 2 3 4 1 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 Inductance (µH) Figure 9 – Max. Iout (A) Vs inductance (µH) Iout, output current (A) Figure 10 – Ifb (mA) Vs Iout (A) www.irf.com 10 AUIPS71411G Case Outline - SO-8 www.irf.com 11 AUIPS71411G Tape & Reel - SO-8 www.irf.com 12 AUIPS71411G Part Marking Information Ordering Information Base Part Number Standard Pack Package Type Form AUIPS71411G SO8 Tube Tape and reel Quantity 95 2500 AUIPS71411G AUIPS71411GTR Complete Part Number www.irf.com 13 AUIPS71411G IMPORTANT NOTICE Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements. For technical support, please contact IR’s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 www.irf.com 14