IR3313SPBF

Data Sheet No. PD60288 revB IR3313SPbF PROGRAMMABLE CURRENT SENSE HIGH SIDE SWITCH Features • • • • • • • Load current feedback Programmable over current shutdown Active clamp ESD protection Input referenced to Vcc Over temperature shutdown Reverse battery protection Product Summary Rds(on) 7 mΩ max. Vcc op. 6 to 32V Current Ratio 8800 Prog. Ishutdown 10 to 90A Vclamp 40V Packages Description The IR3313SPbF is a fully protected 4 terminals high side switch. The input signal is referenced to Vcc. When the input voltage Vcc - Vin is higher than the specified threshold, the output power Mosfet is turned on. When the Vcc - Vin is lower than the specified Vil threshold, the output Mosfet is turned off. A current proportional to the power Mosfet current is sourced to the Ifb pin. Over current shutdown occurs when Vst-Vin > 4.5V. The current shutdown threshold is adjusted by selecting the proper RIfb. Either over current and over temperature latches off the switch. The device is reset by pulling the input pin high. Other integrated protections (ESD, reverse battery, active clamp) make the switch very rugged in automotive environment. D²Pak Pin 4 and 5 fused IR3313SPbF Typical Connection Vcc IN Ifb Current feeback Input On Off IR3313 Battery Out 10k Rifb Logic Ground Power Ground Load www.irf.com 1 IR3313SPbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Vcc lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Min. -16 -16 -16 -0.3 ⎯ ⎯ ⎯ ⎯ ⎯ Max. 37 32 33 37 2.8 100 2 4 0.5 150 ⎯ Units V Vcc-Vin Maximum Vcc voltage Vcc-Vin cont. Maximum continuous Vcc voltage Vcc-Vfb Maximum Ifb voltage Vcc-Vout Maximum output voltage Ids cont. Maximum body diode continuous current Rth=60°C/W (1) Ids pulsed Maximum body diode pulsed current (1) Pd Maximum power dissipation Rth=60°C/W ESD1 Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω ESD2 Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω Tj max. Max. storage & operating temperature junction temperature Min Rfb Minimum on the resistor on Ifb pin Ifb max. Max. Ifb current (1) Limited by junction temperature. Pulsed is also limited by wiring A W kV °C kΩ mA -40 0.3 -50 50 Thermal Characteristics Symbol Rth1 Rth2 Parameter Thermal resistance junction to ambient D²-Pak Std footprint Thermal resistance junction to case D²-Pak Typ. 60 0.7 Max. ⎯ ⎯ Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Iout Parameter Continuous output current Tambient=85°C, Rth=60°C/W, Tj=125°C Min. ⎯ Max. 7 3.5 ⎯ Units A kΩ ms Hz Rifb Recommended Ifb resistor (2)(3) Pulse min. Minimum turn-on pulse width Fmax. Maximum operating frequency 2) If Rifb is too low, the device can be damaged. 3) If Rifb is too high, the device may not switch on. 0.5 1 ⎯ 200 www.irf.com 2 IR3313SPbF Protection Characteristics Tj=25°C, Rifb=500 to 3.5kΩ Symbol Vifb-Vin@Isd Tsd OV Isdf Isd_1k Treset Min. pulse WAIT Rds(on) rev. Parameter Over-current shutdown threshold Over temperature threshold Over voltage protection (not latched) Fixed over current shutdown Programmable over current shutdown 1k Time to reset protection Min. pulse width (no WAIT state) WAIT function timer Reverse battery On state resistance Min. 4 ⎯ Typ. 4.7 165 35 120 40 50 400 1 6.7 Max. 5.6 ⎯ Units V °C V A µs ms mΩ Test Conditions See fig. 5 Vifb 120A Tj > 165°C Min. Pulse + reverse battery protection IN IFB OUT www.irf.com 4 IR3313SPbF Lead Assignments 3- Vcc 1- In 2- Ifb 3- Vcc (tab) 4- Out 5- Out 12 45 D²Pak 90% Vcc-Vin Vih Vil Vhyst IN Icc Vcc IR3313 Iin Ifb Out Vcc-Vout Vclamp1 Vclamp2 Vcc-Vin 10% Tr-in 90% Vcc-5V Vout 10% Td on Td off Tr1 Tr2 Tf Ifb Iout Isd Figure 1 – Voltages and current definitions Figure 2 – Switching time definitions www.irf.com 5 IR3313SPbF T clamp Vin Vcc-Vin Iout T min. pulse T min. pulse Vcc Iout W ai t Vout Vcc - V clamp See Application Notes to evaluate power dissipation Figure 3 – Active clamp waveforms Figure 4 – Min. pulse and Wait function Vcc-Vin t < T reset t > T reset W ait t < T reset t > T reset W ait Over-current shutdown Iout Over-temperature shutdown Tj Figure 5 – Protection Timing Diagrams www.irf.com 6 IR3313SPbF All curves are typical characteristics. Operation in hatched areas is not recommended. Tj=25°C, Rifb=500ohm, Vcc=14V (unless otherwise specified). 1 0 6 Icc off, supply leakage current (µA) 0 1 0 20 30 40 50 8 5 4 3 2 1 0 -50 0 50 100 150 Icc, supply current (mA) 6 4 2 0 Vcc-Vin, supply voltage (V) Figure 6 – Icc (mA) Vs Vcc-Vin (V) Tj, junction temperature (°C) Figure 7 – Icc off (µA) Vs Tj (°C) 200% 6 5 Rds(on), Drain-to-Source On Resistance (Normalized) 150% Vih, Vil and Vifb-Vin@Isd (V) 4 3 2 1 0 Vifb-Vin@Isd VIH VIL 100% 50% -50 0 50 100 150 -50 -25 0 25 50 75 100 125 150 Tj, junction temperature (°C) Figure 8 - Normalized Rds(on) (%) Vs Tj (°C) Tj, junction temperature (°C) Figure 9 – Vih, Vil and Vifb-Vin@Isd (V) Vs Tj (°C) www.irf.com 7 IR3313SPbF 18 16 14 12 100 W ith calibration Spec. Max. Isd, over current shutdown (A) 10 100 Error (+/-A) 10 8 6 4 2 0 0 20 40 60 80 100 1000 10000 I load, load current (A) Figure 10 – Error (+/- A) Vs I load (A) Rifb, feedback resistor (Ω) Figure 11 – Ids (A) Vs Rifb (Ω) 30 60°C/W 35°C/W 100 Max. output current (A) 20 1 0 Max. output current (A) 10 0 -50 0 50 10 0 1 50 10 100 1000 Tamb., ambient temperature (°C) Figure 12 – Max. Iout (A) Vs Tamb. (°C) Inductance (µH) Figure 13 – Max. Iout (A) Vs inductance (µH) www.irf.com 8 IR3313SPbF 100 Tamb=25°C Tamb=100°C 100 Zth, transient thermal impedance (°C/W) 50°C/W free air 10 5°C/W Ids, output current (A) 1 0.1 10 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 0.01 1E-4 1E-3 1E-2 1E-1 1E+0 1E+1 1E+2 Protection response time (s) Figure 14 – Ids (A) Vs over temperature protection response time (s)/ Rth=60°C/W Time (s) Figure 15 – Transient thermal impedance (°C/W) Vs time (s) www.irf.com 9 IR3313SPbF Case Outline 5 Leads - D2PAK – Automotive Q100 PbF MSL1 qualified www.irf.com 10 IR3313SPbF Tape & Reel 5 Lead - D2PAK (SMD220) IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. D2Pak is MSL1 qualified. This product has been designed and qualified for the Automotive [Q100] market. 22/01/2007 www.irf.com 11 Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/