IRHF7130

PD - 90653B REPETITIVE AVALANCHE AND dv/dt RATED HEXFET® TRANSISTOR 100Volt, 0.18Ω , MEGA RAD HARD HEXFET International Rectifier’s RAD HARD technology HEXFETs demonstrate excellent threshold voltage stability and breakdown voltage stability at total radiaition doses as high as 1x106 Rads(Si). Under identical pre- and post-irradiation test conditions, International Rectifier’s RAD HARD HEXFETs retain identical electrical specifications up to 1 x 105 Rads (Si) total dose. No compensation in gate drive circuitry is required. These devices are also capable of surviving transient ionization pulses as high as 1 x 1012 Rads (Si)/Sec, and return to normal operation within a few microseconds. Since the RAD HARD process utilizes International Rectifier’s patented HEXFET technology, the user can expect the highest quality and reliability in the industry. RAD HARD HEXFET transistors also feature all of the well-established advantages of MOSFETs, such as voltage control, very fast switching, ease of paralleling and temperature stability of the electrical parameters. They are well-suited for applications such as switching power supplies, motor controls, inverters, choppers, audio amplifiers and high-energy pulse circuits in space and weapons environments. IRHF7130 IRHF8130 JANSR2N7261 JANSH2N7261 N CHANNEL Product Summary Part Number IRHF7130 IRHF8130 MEGA RAD HARD BVDSS 100V 100V RDS(on) 0.18Ω 0.18Ω ID 8.0A 8.0A Features: n n n n n n n n n n n Radiation Hardened up to 1 x 106 Rads (Si) Single Event Burnout (SEB) Hardened Single Event Gate Rupture (SEGR) Hardened Gamma Dot (Flash X-Ray) Hardened Neutron Tolerant Identical Pre- and Post-Electrical Test Conditions Repetitive Avalanche Rating Dynamic dv/dt Rating Simple Drive Requirements Ease of Paralleling Hermetically Sealed Absolute Maximum Ratings Parameter ID @ VGS = 12V, TC = 25°C ID @ VGS = 12V, TC = 100°C IDM PD @ TC = 25°C VGS EAS dv/dt TJ T STG Continuous Drain Current Continuous Drain Current Pulsed Drain Current ‚ Max. Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy ƒ Peak Diode Recovery dv/dt „ Operating Junction Storage Temperature Range Lead Temperature Weight 8.0 5.0 32 25 0.20 ±20 130 5.5 -55 to 150 Pre-Irradiation IRHF7130, IRHF8130 Units A W W/°C V mJ V/ns o C g 300 (0.063 in. (1.6mm) from case for 10s) 0.98 (typical) www.irf.com 1 10/14/98 IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices Pre-Irradiation Electrical Characteristics @ Tj = 25°C (Unless Otherwise Specified) Parameter BVDSS Drain-to-Source Breakdown Voltage ∆BV DSS/∆T J Temperature Coefficient of Breakdown Voltage RDS(on) Static Drain-to-Source On-State Resistance VGS(th) Gate Threshold Voltage gfs Forward Transconductance IDSS Zero Gate Voltage Drain Current Min 100 — — — 2.0 2.5 — — — — — — — — — — — — — Typ Max Units — 0.10 — — — — — — — — — — — — — — — 5.0 15 — — V V/°C Test Conditions VGS = 0V, ID = 1.0mA Reference to 25°C, ID = 1.0mA VGS = 12V, ID = 5.0A … VGS = 12V, ID = 8.0A … VDS = VGS, ID = 1.0mA VDS > 15V, IDS = 5.0A … VDS= 0.8 x Max Rating,VGS=0V VDS = 0.8 x Max Rating VGS = 0V, TJ = 125°C VGS = 20V VGS = -20V VGS =12V, ID = 8.0A VDS = Max Rating x 0.5 VDD = 50V, ID = 8.0A, RG = 7.5Ω 0.18 Ω 0.185 4.0 V — S( ) 25 µA 250 100 -100 50 12 20 25 55 55 45 — — Ω IGSS IGSS Qg Q gs Q gd td(on) tr td(off) tf LD LS Gate-to-Source Leakage Forward Gate-to-Source Leakage Reverse Total Gate Charge Gate-to-Source Charge Gate-to-Drain (‘Miller’) Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance Internal Source Inductance nA nC ns nH Measured from drain Modified MOSFET symlead, 6mm (0.25 in) bol showing the internal from package to center inductances. of die. Measured from source lead, 6mm (0.25 in) from package to source bonding pad. Ciss C oss C rss Input Capacitance Output Capacitance Reverse Transfer Capacitance — — — 1100 310 55 — — pF VGS = 0V, VDS = 25V f = 1.0MHz Source-Drain Diode Ratings and Characteristics Parameter IS ISM VSD t rr Q RR ton Continuous Source Current (Body Diode) Pulse Source Current (Body Diode) ‚ Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time Min Typ Max Units — — — — — — — — — — 8.0 32 1.5 350 3.0 Test Conditions Modified MOSFET symbol showing the integral reverse p-n junction rectifier. Tj = 25°C, IS = 8.0A, VGS = 0V … Tj = 25°C, IF = 8.0A, di/dt ≤ 100A/µs VDD ≤ 50V … A V ns µC Intrinsic turn-on time is negligible. Turn-on speed is substantially controlled by LS + LD. Thermal Resistance Parameter RthJC Rth-JA Junction-to-Case Junction-to-Ambient Min Typ Max Units — — — — 5.0 175 °C/W Test Conditions Typical socket mount 2 www.irf.com Radiation Characteristics Radiation Performance of Rad Hard HEXFETs IRHF7130, IRHF8130, JANSR-,JANSH-,2N7261 Devices 1, column 2, IRHF8130. The values in Table 1 will be met for either of the two low dose rate test circuits that are used. Both pre- and post-irradiation performance are tested and specified using the same drive circuitry and test conditions in order to provide a direct comEvery manufacturing lot is tested in a low dose rate parison. (total dose) environment per MIL-STD-750, test method 1019 condition A. International Rectifier has High dose rate testing may be done on a special 12 imposed a standard gate condition of 12 volts per request basis using a dose rate up to 1 x 10 Rads (Si)/Sec (See Table 2) note 5 and a VDS bias condition equal to 80% of the device rated voltage per note 6. Pre- and post- irra- International Rectifier radiation hardened HEXFETs diation limits of the devices irradiated to 1 x 105 Rads have been characterized in heavy ion Single Event (Si) are identical and are presented in Table 1, col- Effects (SEE) environments. Single Event Effects charumn 1, IRHF7130. Post-irradiation limits of the devices acterization is shown in Table 3. irradiated to 1 x 106 Rads (Si) are presented in Table International Rectifier Radiation Hardened HEXFETs are tested to verify their hardness capability. The hardness assurance program at International Rectifier comprises three radiation environments. Table 1. Low Dose Rate † Parameter BVDSS VGS(th) IGSS IGSS IDSS RDS(on)1 VSD ‡ IRHF7130 Min Max — 4.0 100 -100 25 0.18 1.5 IRHF8130 Test Conditions ‰ VGS = 0V, ID = 1.0mA VGS = VDS, ID = 1.0mA VGS = 20V VGS = -20 V VDS=0.8 x Max Rating, VGS =0V VGS = 12V, ID = 5.0A TC = 25°C, IS =8.0A,VGS = 0V Min 100 1.25 — — — — — Max — 4.5 100 -100 50 0.24 1.5 V nA µA Ω V 100K Rads (Si) 1000K Rads (Si) Units Drain-to-Source Breakdown Voltage 100 Gate Threshold Voltage … 2.0 Gate-to-Source Leakage Forward — Gate-to-Source Leakage Reverse — Zero Gate Voltage Drain Current — Static Drain-to-Source … — On-State Resistance One Diode Forward Voltage … — Table 2. High Dose Rate Parameter VDSS IPP di/dt L1 ˆ 1011 Rads (Si)/sec 1012 Rads (Si)/sec Drain-to-Source Voltage Min Typ Max Min Typ Max Units Test Conditions — — 80 — — 80 V Applied drain-to-source voltage during gamma-dot — 100 — — 100 — A Peak radiation induced photo-current — — 800 — — 160 A/µsec Rate of rise of photo-current 0.1 — — 0.5 — — µH Circuit inductance required to limit di/dt Table 3. Single Event Effects Ion Cu LET (Si) (MeV/mg/cm2) 28 Fluence (ions/cm2) 3x 105 Range (µm) ~43 VDSBias (V) 100 VGS Bias (V) -5 www.irf.com 3 IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices Post-Irradiation Fig 1. Typical Response of Gate Threshhold Voltage Vs. Total Dose Exposure Fig 2. Typical Response of On-State Resistance Vs. Total Dose Exposure Fig 3. Typical Response of Transconductance Vs. Total Dose Exposure Fig 4. Typical Response of Drain to Source Breakdown Vs. Total Dose Exposure 4 www.irf.com Post-Irradiation IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices Fig 5. Typical Zero Gate Voltage Drain Current Vs. Total Dose Exposure Fig 6. Typical On-State Resistance Vs. Neutron Fluence Level Fig 8a. Gate Stress of VGSS Equals 12 Volts During Radiation Fig 7. Typical Transient Response of Rad Hard HEXFET During 1x1012 Rad (Si)/Sec Exposure Fig 8b. VDSS Stress Equals 80% of BVDSS During Radiation Fig 9. High Dose Rate (Gamma Dot) Test Circuit www.irf.com 5 IRHF7130, IRHF8130, JANSR-,JANSH-,2N7261 Devices Note: Bias Conditions during radiation: VGS = 12 Vdc, VDS = 0 Vdc Radiation Characterstics Fig 10. Typical Output Characteristics Pre-Irradiation Fig 11. Typical Output Characteristics Post-Irradiation 100K Rads (Si) Fig 12. Typical Output Characteristics Post-Irradiation 300K Rads (Si) Fig 13. Typical Output Characteristics Post-Irradiation 1 Mega Rads(Si) 6 www.irf.com Radiation Characterstics IRHF7130, IRHF8130, JANSR-,JANSH-,2N7261 Devices Note: Bias Conditions during radiation: VGS = 0 Vdc, VDS = 80 Vdc Fig 14. Typical Output Characteristics Pre-Irradiation Fig 15. Typical Output Characteristics Post-Irradiation 100K Rads (Si) Fig 16. Typical Output Characteristics Post-Irradiation 300K Rads (Si) Fig 17. Typical Output Characteristics Post-Irradiation 1 Mega Rads(Si) www.irf.com 7 IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices Pre-Irradiation Fig 18. Typical Output Characteristics Fig 19. Typical Output Characteristics Fig 20. Typical Transfer Characteristics Fig 21. Normalized On-Resistance Vs. Temperature 8 www.irf.com Pre-Irradiation IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices 30 Fig 22. Typical Capacitance Vs. Drain-to-Source Voltage Fig 23. Typical Gate Charge Vs. Gate-to-Source Voltage Fig 24. Typical Source-Drain Diode Forward Voltage Fig 25. Maximum Safe Operating Area www.irf.com 9 IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices Pre-Irradiation V DS VGS RG RD D.U.T. + -V DD 12V Pulse Width ≤ 1 µs Duty Factor ≤ 0.1 % Fig 27a. Switching Time Test Circuit VDS 90% 10% VGS Fig 26. Maximum Drain Current Vs. Case Temperature td(on) tr t d(off) tf Fig 27b. Switching Time Waveforms Fig 28. Maximum Effective Transient Thermal Impedance, Junction-to-Case 10 www.irf.com Pre-Irradiation IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices 1 5V VD S L D R IV E R RG D .U .T IA S + - VD D A 12V 20V tp 0 .0 1 Ω Fig 29a. Unclamped Inductive Test Circuit V (B R )D S S tp Fig 29c. Maximum Avalanche Energy Vs. Drain Current IAS Fig 29b. Unclamped Inductive Waveforms Current Regulator Same Type as D.U.T. 50KΩ QG 12V .2µF .3µF 12 V QGS VG QGD VGS 3mA D.U.T. + V - DS Charge IG ID Current Sampling Resistors Fig30a. Basic Gate Charge Waveform Fig 30b. Gate Charge Test Circuit www.irf.com 11 IRHF7130, IRHF8130,JANSR-,JANSH-,2N7261 Devices  See Figures 18 through 30 for pre-radiation ‚ ƒ „ curves Repetitive Rating; Pulse width limited by maximum junction temperature. Refer to current HEXFET reliability report. VDD = 25V, Starting TJ = 25°C, Peak IL = 8.0A,L>3.0mH RG=25Ω ISD ≤ 8.0A, di/dt ≤ 140A/µs, VDD ≤ BVDSS, TJ ≤ 150°C Suggested RG =7.5Ω Pulse width ≤ 300 µs; Duty Cycle ≤ 2% Pre-Irradiation † Total Dose Irradiation with VGS Bias. 12 volt VGS applied and VDS = 0 during irradiation per MIL-STD-750, method 1019, codition A. ‡ Total Dose Irradiation with VDS Bias. VDS = 0.8 rated BVDSS (pre-radiation) applied and VGS = 0 during irradiation per MlL-STD-750, method 1019, condition A. ˆ This test is performed using a flash x-ray source operated in the e-beam mode (energy ~2.5 MeV), 30 nsec pulse. ‰ All Pre-Irradiation and Post-Irradiation test conditions are identical to facilitate direct comparison for circuit applications. … Case Outline and Dimensions — TO-205AF (Modified TO-39) All dimensions are shown millimeters (inches) WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331 IR GREAT BRITAIN: Hurst Green, Oxted, Surrey RH8 9BB, UK Tel: ++ 44 1883 732020 IR CANADA: 15 Lincoln Court, Brampton, Ontario L6T3Z2, Tel: (905) 453 2200 IR GERMANY: Saalburgstrasse 157, 61350 Bad Homburg Tel: ++ 49 6172 96590 IR ITALY: Via Liguria 49, 10071 Borgaro, Torino Tel: ++ 39 11 451 0111 IR FAR EAST: K&H Bldg., 2F, 30-4 Nishi-Ikebukuro 3-Chome, Toshima-Ku, Tokyo Japan 171 Tel: 81 3 3983 0086 IR SOUTHEAST ASIA: 1 Kim Seng Promenade, Great World City West Tower, 13-11, Singapore 237994 Tel: ++ 65 838 4630 IR TAIWAN:16 Fl. Suite D. 207, Sec. 2, Tun Haw South Road, Taipei, 10673, Taiwan Tel: 886-2-2377-9936 http://www.irf.com/ Data and specifications subject to change without notice. 10/98 12 www.irf.com