IRS21064PBF

Data Sheet No. PD60260 IRS2108/IRS21084(S)PbF Features HALF-BRIDGE DRIVER Packages 8-Lead PDIP 14-Lead PDIP • Floating channel designed for bootstrap operation • Fully operational to +600 V • Tolerant to negative transient voltage, dV/dt • • • • • • • • • • • immune Gate drive supply range from 10 V to 20 V Undervoltage lockout for both channels 3.3 V, 5 V, and 15 V input logic compatible Cross-conduction prevention logic Matched propagation delay for both channels High-side output in phase with HIN input Low-side output out of phase with LIN input Logic and power ground +/- 5 V offset Internal 540 ns deadtime, and programmable up to 5 µs with one external RDT resistor (IRS21084) Lower di/dt gate driver for better noise immunity RoHS compliant 8-Lead SOIC 14-Lead SOIC Feature Comparison The IRS2108/IRS21084 are high voltCrossage, high speed power MOSFET and Deadtime ton/toff Input conduction Part Ground Pins IGBT drivers with dependent high- and logic prevention (ns) (ns) logic low-side referenced output channels. 2106/2301 COM HIN/LIN no none 220/200 Proprietary HVIC and latch immune 21064 VSS/COM 2108 Internal 540 COM CMOS technologies enable ruggedized HIN/LIN yes 220/200 Programmable 540 - 5000 21084 VSS/COM monolithic construction. The logic input 2109/2302 Internal 540 COM IN/SD yes 750/200 is compatible with standard CMOS or Programmable 540 - 5000 21094 VSS/COM LSTTL output, down to 3.3 V logic. The yes 160/140 HIN/LIN Internal 100 2304 COM output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high-side configuration which operates up to 600 V. Description Typical Connection VCC up to 600 V VCC HIN LIN VB HO VS LO up to 600 V TO LOAD HIN LIN COM IRS2108 VCC HIN LIN VCC HIN LIN DT VSS RDT VSS IRS21084 HO VB VS TO LOAD (Refer to Lead Assignments for correct pin configuration). These diagrams show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. COM LO www.irf.com 1 IRS2108/IRS21084(S)PbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol VB VS VHO VCC VLO DT VIN VSS dVS/dt Definition High-side floating absolute v oltage High-side floating supply offset voltage High-side floating output voltage Low-side and logic fixed supply voltage Low-side output voltage Programmable deadtime pin voltage (IRS21084 only) Logic input voltage (HIN & LIN ) Logic ground (IRS21084 only ) Allowable offset supply voltage transient (8 lead PDIP) (8 lead SOIC) (14 lead PDIP) (14 lead SOIC) (8 lead PDIP) (8 lead SOIC) (14 lead PDIP) (14 lead SOIC) Min. -0.3 VB - 25 VS - 0.3 -0.3 -0.3 V SS - 0.3 VSS - 0.3 VCC - 25 — — — — — — — — — — -50 — Max. 625 VB + 0.3 VB + 0.3 25 VCC + 0.3 VCC + 0.3 VCC + 0.3 VCC + 0.3 50 1.0 0.625 1.6 1.0 125 200 75 120 150 150 300 Units V V/ns PD Package power dissipation @ TA ≤ +25 oC W RthJA Thermal resistance, junction to ambient °C/W TJ TS TL Junction temperature Storage temperature Lead temperature (soldering, 10 seconds) °C Recommended Operating Conditions The input/output logic timing diagram is shown in Fig. 1. For proper operation the device should be used within the recommended conditions. The VS and VSS offset rating are tested with all supplies biased at a 15 V differential. Symbol VB VS VHO VCC VLO Definition High-side floating supply absolute voltage High-side floating supply offset voltage High-side floating output voltage Low-side and logic fixed supply voltage Low-side output voltage Min. VS + 10 Note 1 VS 10 0 COM VSS Max. VS + 20 600 VB 20 VCC VCC VCC Units V IRS2108 VIN Logic input voltage IRS21084 DT Programmable deadtime pin voltage (IRS21084 only) VS VCC VSS Logic ground (IRS21084 only ) -5 5 TA Ambient temperature -40 125 °C Note 1: Logic operational for VS of -5 V to +600 V. Logic state held for VS of -5 V to -VBS. (Please refer to the Design Tip DT97-3 for more details). www.irf.com 2 IRS2108/IRS21084(S)PbF Dynamic Electrical Characteristics VBIAS (VCC, VBS) = 15 V, VSS = COM, CL = 1000 pF, TA = 25 °C, DT = VSS unless otherwise specified. Symbol ton toff MT tr tf DT MDT Definition Turn-on propagation delay Turn-off propagation delay Delay matching | ton - toff | Turn-on rise time Turn-off fall time Deadtime: LO turn-off to HO turn-on(DTLO-HO) & HO turn-off to LO turn-on (DTHO-LO) Deadtime matching = | DTLO-HO - DTHO-LO | Min. — — — — — 400 4 — — Typ. 220 200 0 100 35 540 5 0 0 Max. Units Test Conditions 300 280 30 220 80 680 6 60 600 µs ns ns VS = 0 V RDT= 0 Ω RDT = 200 kΩ (IR21084) RDT=0 Ω RDT= 200 kΩ (IR21084) VS = 0 V VS = 0 V or 600 V Static Electrical Characteristics VBIAS (VCC, VBS) = 15 V, V SS = COM, DT= V SS and TA = 25 °C unless otherwise specified. The VIL, VIH, and IIN parameters are referenced to VSS/COM and are applicable to the respective input leads: HIN and LIN. The VO, IO, and Ron parameters are referenced to COM and are applicable to the respective output leads: HO and LO. Symbol VIH VIL VOH VOL ILK IQBS IQCC IIN+ IINVCCUV+ VBSUV+ VCCUVVBSUVVCCUVH VBSUVH IO+ IO- Definition Logic “1” input voltage for HIN & logic “0” for LIN Logic “0” input voltage for HIN & logic “1” for LIN High level output voltage, VBIAS - VO Low level output voltage, VO Offset supply leakage current Quiescent VBS supply current Quiescent VCC supply current Logic “1” input bias current Logic “0” input bias current VCC and VBS supply undervoltage positive going threshold VCC and VBS supply undervoltage negative going threshold Hysteresis Output high short circuit pulsed current Output low short circuit pulsed current Min. Typ. Max. Units Test Conditions 2.5 — — — — 20 0.4 — — 8.0 7.4 0.3 120 250 — — 0.05 0.02 — 75 1.0 5 — 8.9 8.2 0.7 290 600 — 0.8 0.2 0.1 50 130 1.6 20 5 VCC = 10 V to 20 V V IO = 2 mA VB = VS = 600 V µA mA VIN = 0 V or 5 V VIN = 0 V or 5 V RDT=0 Ω HIN = 5 V, LIN = 0 V µA HIN = 0 V, LIN = 5 V 9.8 9.0 — — mA — VO = 0 V, PW ≤ 10 µs VO = 15 V, PW ≤ 10 µs V www.irf.com 3 IRS2108/IRS21084(S)PbF Functional Block Diagram VB 2108 HV LEVEL SHIFTER UV DETECT R PULSE FILTER R S Q HO HIN VSS/COM LEVEL SHIFT VS PULSE GENERATOR DT DEADTIME & SHOOT-THROUGH PREVENTION UV DETECT VCC +5V LO LIN VSS/COM LEVEL SHIFT DELAY COM VSS VB 21084 HIN VSS/COM LEVEL SHIFT HV LEVEL SHIFTER PULSE GENERATOR UV DETECT R PULSE FILTER R S Q HO VS DT +5V DEADTIME & SHOOT-THROUGH PREVENTION UV DETECT VCC LO LIN VSS/COM LEVEL SHIFT DELAY COM VSS www.irf.com 4 IRS2108/IRS21084(S)PbF Lead Definitions Symbol Description HIN LIN DT VSS VB HO VS VCC LO COM Logic input for high-side gate driver output (HO), in phase (referenced to COM for IRS2108 and VSS for IRS21084) Logic input for low-side gate driver output (LO), out of phase (referenced to COM for IRS2108 and VSS for IRS21084) Programmable deadtime lead, referenced to VSS (IR21084 only) Logic ground (IRS21084 only) High-side floating supply High-side gate driver output High-side floating supply return Low-side and logic fixed supply Low-side gate driver output Low-side return Lead Assignments 1 2 3 4 VCC HIN LIN COM VB HO VS LO 8 7 6 5 1 2 3 4 VCC HIN LIN COM VB HO VS LO 8 7 6 5 8 Lead PDIP 8 Lead SOIC IRS2108PbF IRS2108SPbF 1 2 3 4 5 6 7 VCC HIN LIN DT VSS COM LO VB HO VS 14 13 12 11 10 9 8 1 2 3 4 5 6 7 VCC HIN LIN DT VSS COM LO VB HO VS 14 13 12 11 10 9 8 14 Lead PDIP 14 Lead SOIC IRS21084PbF www.irf.com IRS21084SPbF 5 IRS2108/IRS21084(S)PbF HIN LIN HO LIN 50% 50% LO ton Figure 1. Input/Output Timing Diagram tr 90% toff 90% tf LO 10% 10% 50% 50% HIN ton tr 90% HIN LIN 50% 50% toff 90% tf HO 90% 10% 10% Figure 2. Switching Time Waveform Definitions HO LO DT LO-HO 10% DT HO-LO 90% 10% MDT= DT LO-HO - DT HO-LO Figure 3. Deadtime Waveform Definitions www.irf.com 6 IRS2108/IRS21084(S)PbF Turn-On Propagation Delay (ns) 400 300 M ax. Turn-On Propagation Delay (ns) 500 500 400 M ax. 300 200 100 0 10 12 14 16 18 20 V BIAS Supply Voltage (V) Figure 4B. Turn-On Propagation Delay vs. Supply Voltage Typ. 200 Typ. 100 0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 4A. Turn-On Propagation Delay vs. Tem perature Turn-Off Propagation Delay (ns) Turn-Off Propagation Delay (ns) 500 400 300 M ax. 500 400 M ax. 300 Typ. 200 Typ. 200 100 0 10 12 14 16 18 20 V BIAS Supply Voltage (V) Figure 5B. Turn-Off Propagation Delay vs. Supply Voltage 100 0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 5A. Turn-Off Propagation Delay vs.Tem perature www.irf.com 7 IRS2108/IRS21084(S)PbF 500 Turn-On Rise Time (ns ) 500 Turn-On Rise Time (ns) 400 300 Max. 400 300 200 Max. 200 100 0 100 Typ. Typ. 0 -50 -25 0 25 50 o 75 100 125 10 12 14 16 18 20 Temperature ( C) Figure 6A. Turn-On Rise Time vs.Temperature V BIAS Supply Voltage (V) Figure 6B. Turn-On Rise Time vs. Supply Voltage 200 200 Turn-Off Fall Time (ns) 150 100 50 0 -50 Turn-Off Fall Time Time ) Turn-Off Fall (ns) -25 0 25 50 o 150 100 50 0 75 100 125 10 12 14 16 18 20 Temperature ( C) Figure 7A. Turn-Off Fall Tim e vs. Temperature Input Voltage (V) Figure 7B. Turn-Off Fall Time vs. Input voltage www.irf.com 8 IRS2108/IRS21084(S)PbF 1000 800 Max. 1000 800 600 400 200 -25 0 25 50 75 100 125 Deadtime (ns) Deadtime (ns) Max. Typ. 600 Typ. Min. 400 Min. 200 -50 10 12 14 16 18 20 Temperature (oC) Figure 8A. Deadtim e vs. Tem perature V BIAS Supply Voltage (V) Figure 8B. Deadtim e vs. Supply Voltage 7 6 Max. 8 7 Input Voltage (V) 6 5 4 3 2 1 0 -50 Min. Deadtime ((µs) 5 4 3 2 1 0 0 50 100 RDT ( kΩ) Figure 8C. Deadtim e vs. RDT ( IR21084 Only) 150 Typ. Min. 200 -25 0 25 50 o 75 100 125 Temperature ( C) Figure 9A. Logic "1" Input Voltage vs. Tem perature www.irf.com 9 IRS2108/IRS21084(S)PbF 8 7 4.0 Input Voltage (V) 3.2 2.4 1.6 0.8 Min. Input Voltage (V) 6 5 4 3 2 1 0 10 12 14 16 18 20 V BAIS Supply Voltage (V) Figure 9B. Logic "1" Input Voltage vs. Supply Voltage Min. 0.0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 10A. Logic "0" Input Voltage vs. Tem perature 4.0 3.2 2.4 1.6 0.8 0.0 10 12 14 16 18 20 V CC Supply Voltage (V) Figure 10B. Logic "0" Input Voltage vs. Supply Voltage Min. High Level Output Voltage (V ) 0.5 0.4 0.3 0.2 0.1 Typ. Input Voltage (V) Max. 0.0 -50 -25 0 25 50 75 100 125 Temperature (oC) Figure 11A. High Level Output Voltage vs. Temperature www.irf.com 10 IRS2108/IRS21084(S)PbF High Level Output Voltage (V) 0.4 0.3 0.2 0.1 Typ. Max. Low Level Output Voltage (V) 0.5 0.5 0.4 0.3 0.2 0.1 Max. Typ. 0.0 10 12 14 16 18 20 VBAIS Supply Voltage (V) Figure 11B. High Lovel Output Voltage vs. Supply Voltage 0.0 -50 -25 0 25 50 o 75 100 125 Temperature ( C) Figure 12A. Low Level Output Voltage vs.Temperature Low Level Output Voltage (V) 0.5 0.4 0.3 0.2 Max. ( A) Offset Supply Leakage Current ( µA) 500 400 300 200 100 M ax. 0.1 Typ. 0 10 12 14 16 18 20 V BIAS Supply Voltage (V) Figure 12B. Low Level Output Voltage vs. Supply Voltage 0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 13A. Offset Supply Leakage Current vs. Tem perature www.irf.com 11 IRS2108/IRS21084(S)PbF Offset Supply Leakage Current (( A) µ A) 500 400 300 200 100 M ax. 400 A) V BS Supply Current (µA) 300 200 M ax. 100 Typ. Mi n. 0 0 100 200 300 400 500 600 V B Boost Voltage (V) Figure 13B. Offset Supply Leakage Current vs. Tem perature 0 -50 -25 0 25 50 75 Temperature ( oC) 100 125 Figure 14A. V BS Supply Current vs. Tem perature 400 VCC Supply Current (mA) 3.0 2.5 2.0 M ax. A) V BS Supply Current (µA) 300 200 M ax. Typ. Mi n. 1.5 Typ. 1.0 0.5 Mi n. 100 0 10 12 14 16 18 20 V BS Supply Voltage (V) Figure 14B. V BS Supply Current vs. Supply Voltage 0.0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 15A. V CC Supply Current vs. Tem perature www.irf.com 12 IRS2108/IRS21084(S)PbF 3.0 V CC Supply Current (mA) 2.5 2.0 1.5 1.0 0.5 0.0 10 12 14 16 18 V CC Supply Voltage (V) 20 Max. Typ. Min. 60 ( Logic "1" Input Current ( µA) 50 40 30 20 10 0 -50 -25 0 25 50 o Max. Typ. 75 100 125 Temperature ( C) Figure 16A. Logic "1" Input Current vs. Tem perature Figure 15B. V CC Supply Current vs. Supply Voltage 60 50 40 30 Max. Lo gic "0" Input Bia s Current (µA) 6 5 4 3 2 1 0 -50 Max µA Logic "1" Input Current(µA)) ( 20 10 0 10 12 14 16 18 20 V CC Supply Voltage (V) Figure 16B. Logic "1" Input Current vs. Supply Voltage Typ. -25 0 25 50 75 100 125 Temperature (°C) Figure 17A. Logic "0" Input Bias Current vs. Temperature www.irf.com 13 IRS2108/IRS21084(S)PbF Logic "0" Input Bias C urrent (µA) 6 5 4 3 2 1 0 10 12 14 16 18 20 Max V CC UVLO Threshold (+) (V) 12 11 10 9 8 7 -50 -25 0 25 50 o Max. Typ. Min. 75 100 125 Supply Voltage (V) F i gure 17B. Lo gic "0" Input Bias Cur rent Figure 17B. Logic "0" Input Bias Current vs. Voltage Temperature ( C) Figure 18. V CC Undervoltage Threshold (+) vs. Tem perature 11 VCC UVLO Threshold (-) (V) 10 9 8 Min. Max. 12 V BS UVLO Threshold (+) (V) 11 10 9 8 Max. Typ. Typ. 7 6 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 19. V CC Undervoltage Threshold (-) vs. Tem perature Min. 7 -50 -25 0 25 50 o 75 100 125 Temperature ( C) Figure 20. V BS Undervoltage Threshold (+) vs. Tem perature www.irf.com 14 IRS2108/IRS21084(S)PbF V BS UVLO Threshold (-) (V) Output Source Current (m ) (mA) Α 11 10 9 8 Mi n. M ax. Typ. 500 400 Typ. 300 200 100 Min. 7 6 -50 -25 0 25 50 75 100 125 0 -50 -25 0 25 50 75 100 125 Temperature ( oC) Figure 21. V BS Undervoltage Threshold (-) vs. Tem perature Temperature (oC) Figure 22A. Output Source Current vs. Tem perature Output Source Current (mA) (m ) Α 500 400 300 200 Typ. 1000 Output Sink Current (m ) (mA) Α 800 600 400 Min. Typ. 100 Min. 200 0 -50 0 10 12 14 16 18 20 VBIAS Supply Voltage (V) Figure 22B. Output Source Current vs. Supply Voltage -25 0 25 50 75 100 125 Temperature (oC) Figure 23A. Output Sink Curre nt vs .Te m pe rature www.irf.com 15 IRS2108/IRS21084(S)PbF 1000 800 600 400 Typ. 0 V S Offset Supply Voltage (V) -2 Typ. Output Sink Current (mA) -4 -6 -8 -10 200 Min. 0 10 12 14 16 18 20 10 12 14 16 18 20 VBIAS Supply Voltage (V) Figure 23B. Output Sink Current vs. Supply Voltage V BS Floating Supply Voltage (V) Figure 24. Maxim um V s Negative Offset vs. Supply Voltage 140 120 o Temperature (o C) Temperature ( C) 140 120 Temperature (o C) 100 80 60 40 20 1 10 100 1000 Frequency (kHz) 1V 40 70 V 0V 100 1V 40 80 70 V 60 40 20 1 10 100 0V 1000 Frequency (kHz) Figure 26. IRS2108 vs. Frequency (IRFBC30), Rgate=22 Ω , V CC=15 V Figure 25. IRS2108 vs. Frequency (IRFBC20), Rgate=33 Ω , V CC=15 V www.irf.com 16 IRS2108/IRS21084(S)PbF 1 40 140 120 1 V 70 V 40 0V 1 20 Temperature (o C) Temperature (o C) 1 00 1V 40 70 V 100 80 60 40 80 60 0V 40 20 20 1 1 0 1 00 1 000 1 10 100 1000 Frequency (kHz) Figure 27. IRS2108 vs. Frequency (IRFBC40), Rgate=15 Ω , V CC=15 V Frequency (kHz) Figure 28. IRS2108 vs. Frequency (IRFPE50), Rgate=10 Ω , V CC=15 V 140 1 40 Temperature (o C) 100 80 60 40 20 1 10 100 1000 1V 40 70 V 0V p () Temperature (o C) 120 1 20 1 00 80 1V 40 60 70 V 40 0V 20 1 1 0 1 00 1 000 Frequency (kHz) Figure 29. IRS21084 vs. Frequency (IRFBC20), Rgate=33 Ω , V CC=15 V Frequency (kHz) Figure 30. IRS21084 vs. Frequency (IRFBC30), Rgate=22 Ω , V CC=15 V www.irf.com 17 IRS2108/IRS21084(S)PbF 140 120 1 40 1V 40 1 20 70 V Temperature (o C) 100 1V 40 Temperature (o C) 1 00 0V 80 80 60 40 20 1 10 100 70 V 0V 60 40 1000 20 1 1 0 1 00 1 000 Frequency (kHz) Figure 31. IRS21084 vs. Frequency (IRFBC40), Rgate=15 Ω , V CC=15 V Frequency (kHz) Figure 32. IRS21084 vs. Frequency (IRFPE50), Rgate=10 Ω , V CC=15 V 140 120 1 40 1 20 Temperature (o C) Temperature (o C) 100 80 60 40 20 1 10 100 1000 Frequency (kHz) Figure 33. IRS2108S vs. Frequency (IRFBC20), Rgate=33 Ω , V CC=15 V 1V 40 70 V 0V 1 00 1V 40 70 V 80 0V 60 40 20 1 1 0 1 00 1 000 Frequency (kHz) Figure 34. IRS2108S vs. Frequency (IRFBC30), Rgate=22 Ω , V CC=15 V www.irf.com 18 IRS2108/IRS21084(S)PbF 140 120 1 V 70 V 40 140 1 V 70 V 0 V 40 Temperature (o C) Temperature (o C) 120 100 80 60 40 20 100 80 60 40 20 1 10 100 0V 1 1000 Frequency (kHz) 10 100 1000 Frequency (kHz) Figure 36. IRS2108S vs. Frequency (IRFPE50), Rgate=10 Ω , V CC=15 V Figure 35. IRS2108S vs. Frequency (IRFBC40), Rgate=15 Ω , V CC=15 V 140 120 1 40 1 20 Temperature (o C) Temperature (o C) 100 80 60 40 20 1 10 100 1000 1V 40 70 V 0V 1 00 80 1V 40 70 V 60 0V 40 20 1 1 0 1 00 1 000 Frequency (kHz) Figure 37. IRS21084S vs. Frequency (IRFBC20), Rgate=33 Ω , V CC=15 V Frequency (kHz) Figure 38. IR21084S vs. Frequency (IRFBC30), Rgate=22 Ω , V CC=15 V www.irf.com 19 IRS2108/IRS21084(S)PbF 140 120 140 120 1 V 70 V 40 0V Temperature (o C) 100 80 60 40 20 1 10 100 Temperature (o C) 1V 40 70 V 0V 100 80 60 40 20 1000 1 10 100 1000 Frequency (kHz) Figure 39. IRS21084S vs. Frequency (IRFBC40), Rgate=15 Ω , V CC=15 V Frequency (kHz) Figure 40. IRS21084S vs. Frequency (IRFPE50), Rgate=10 Ω , V CC=15 V www.irf.com 20 IRS2108/IRS21084(S)PbF Case outlines 8-Lead PDIP DIM FOOTPRINT 8X 0.72 [.028] 01-6014 01-3003 01 (MS-001AB) D A 5 B INCHES MIN .0532 .013 .0075 .189 .1497 MAX .0688 .0098 .020 .0098 .1968 .1574 MILLIMETERS MIN 1.35 0.10 0.33 0.19 4.80 3.80 MAX 1.75 0.25 0.51 0.25 5.00 4.00 A b c D A1 .0040 6 E 8 7 6 5 H 0.25 [.010] A E 6.46 [.255] 1 2 3 4 e e1 H K L 8X 1.78 [.070] .050 BASIC .025 BASIC .2284 .0099 .016 0° .2440 .0196 .050 8° 1.27 BASIC 0.635 BASIC 5.80 0.25 0.40 0° 6.20 0.50 1.27 8° 6X e e1 3X 1.27 [.050] y A C 0.10 [.004] y K x 45° 8X b 0.25 [.010] NOTES: A1 CAB 8X L 7 8X c 1. DIMENSIONING & TOLERANC ING PER ASME Y14.5M-1994. 2. CONTROLLING DIMENSION: MILLIMETER 3. DIMENSIONS ARE SHOWN IN MILLIMETERS [INC HES]. 4. OUTLINE C ONFORMS TO JEDEC OUTLINE MS-012AA. 5 DIMENSION DOES NOT INCLUDE MOLD PROTRUSIONS. MOLD PROTRUSIONS NOT TO EXCEED 0.15 [.006]. 6 DIMENSION DOES NOT INCLUDE MOLD PROTRUSIONS. MOLD PROTRUSIONS NOT TO EXCEED 0.25 [.010]. 7 DIMENSION IS THE LENGTH OF LEAD FOR SOLDERING TO A SUBSTRATE. 8-Lead SOIC www.irf.com 01-6027 01-0021 11 (MS-012AA) 21 IRS2108/IRS21084(S)PbF 14 Lead PDIP 01-6010 01-3002 03 (MS-001AC) 14-Lead SOIC (narrow body) 01-6019 01-3063 00 (MS-012AB) www.irf.com 22 IRS2108/IRS21084(S)PbF Tape & Reel 8-lead SOIC LOAD ED TA PE FEED DIRECTION B A H D F C N OT E : CO NTROLLING D IM ENSION IN MM E G C A R R I E R T A P E D IM E N S I O N F O R 8 S O I C N M etr ic Im p er i al Co d e M in M ax M in M ax A 7 .9 0 8.1 0 0. 31 1 0 .3 18 B 3 .9 0 4.1 0 0. 15 3 0 .1 61 C 11 .7 0 1 2. 30 0 .4 6 0 .4 84 D 5 .4 5 5.5 5 0. 21 4 0 .2 18 E 6 .3 0 6.5 0 0. 24 8 0 .2 55 F 5 .1 0 5.3 0 0. 20 0 0 .2 08 G 1 .5 0 n/ a 0. 05 9 n/ a H 1 .5 0 1.6 0 0. 05 9 0 .0 62 F D C E B A G H R E E L D IM E N S I O N S F O R 8 S O IC N M etr ic Im p er i al Co d e M in M ax M in M ax A 32 9. 60 3 30 .2 5 1 2 .9 76 13 .0 0 1 B 20 .9 5 2 1. 45 0. 82 4 0 .8 44 C 12 .8 0 1 3. 20 0. 50 3 0 .5 19 D 1 .9 5 2.4 5 0. 76 7 0 .0 96 E 98 .0 0 1 02 .0 0 3. 85 8 4 .0 15 F n /a 1 8. 40 n /a 0 .7 24 G 14 .5 0 1 7. 10 0. 57 0 0 .6 73 H 12 .4 0 1 4. 40 0. 48 8 0 .5 66 www.irf.com 23 IRS2108/IRS21084(S)PbF Tape & Reel 14-lead SOIC LOAD ED TA PE FEED DIRECTION B A H D F C N OT E : CO NTROLLING D IM ENSION IN MM E G C A R R I E R T A P E D IM E N S I O N F O R 1 4 S O IC N M etr ic Im p er i al Co d e M in M ax M in M ax A 7 .9 0 8.1 0 0. 31 1 0 .3 18 B 3 .9 0 4.1 0 0. 15 3 0 .1 61 C 15 .7 0 1 6. 30 0. 61 8 0 .6 41 D 7 .4 0 7.6 0 0. 29 1 0 .2 99 E 6 .4 0 6.6 0 0. 25 2 0 .2 60 F 9 .4 0 9.6 0 0. 37 0 0 .3 78 G 1 .5 0 n/ a 0. 05 9 n/ a H 1 .5 0 1.6 0 0. 05 9 0 .0 62 F D C E B A G H R E E L D IM E N S I O N S F O R 1 4 SO IC N M etr ic Im p er i al Co d e M in M ax M in M ax A 32 9. 60 3 30 .2 5 1 2 .9 76 13 .0 0 1 B 20 .9 5 2 1. 45 0. 82 4 0 .8 44 C 12 .8 0 1 3. 20 0. 50 3 0 .5 19 D 1 .9 5 2.4 5 0. 76 7 0 .0 96 E 98 .0 0 1 02 .0 0 3. 85 8 4 .0 15 F n /a 2 2. 40 n /a 0 .8 81 G 18 .5 0 2 1. 10 0. 72 8 0 .8 30 H 16 .4 0 1 8. 40 0. 64 5 0 .7 24 www.irf.com 24 IRS2108/IRS21084(S)PbF LEADFREE PART MARKING INFORMATION Part number S IRxxxxxx Date code YWW? ?XXXX IR logo Pin 1 Identifier ? P MARKING CODE Lead Free Released Non-Lead Free Released Lot Code (Prod mode - 4 digit SPN code) Assembly site code Per SCOP 200-002 ORDER INFORMATION 8-Lead PDIP IRS2108PbF 8-Lead SOIC IRS2108SPbF 8-Lead SOIC Tape & Reel IRS2108STRPbF 14-Lead PDIP IRS21084PbF 14-Lead SOIC IRS21084SPbF 14-Lead SOIC Tape & Reel IRS21084STRPbF The SOIC-8 is MSL2 qualified. The SOIC-14 is MSL3 qualified. This product has been designed and qualified for the industrial level. Qualification standards can be found at www.irf.com IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 Data and specifications subject to change without notice. 12/4/2006 www.irf.com 25