MURD620CTPBF

Bulletin PD-21093 09/05 MURD620CTPbF Ultrafast Rectifier Features • • • • • Ultrafast Recovery Time Low Forward Voltage Drop Low Leakage Current 175°C Operating Junction Temperature Lead-Free ("PbF" suffix) t rr = 25ns IF(AV) = 6Amp VR = 200V Description/ Applications International Rectifier's MUR.. series are the state of the art Ultra fast recovery rectifiers specifically designed with optimized performance of forward voltage drop and ultra fast recovery time. The planar structure and the platinum doped life time control, guarantee the best overall performance, ruggedness and reliability characteristics. These devices are intended for use in the output rectification stage of SMPS, UPS, DC-DC converters as well as free-wheeling diode in low voltage inverters and chopper motor drives. Their extremely optimized stored charge and low recovery current minimize the switching losses and reduce over dissipation in the switching element and snubbers. Package Outline D-PAK Absolute Maximum Ratings Parameters VRRM IF(AV) IFSM IFM TJ, TSTG Peak Repetitive Peak Reverse Voltage Average Rectified Forward Current Total Device, (Rated VR ), TC = 146°C Non Repetitive Peak Surge Current Peak Repetitive Forward Current (Rated VR , Square wave, 20 KHz), TC = 146°C Operating Junction and Storage Temperatures - 65 to 175 °C Per Diode 50 6 Per Device Max 200 6 Units V A www.irf.com 1 MURD620CTPbF Bulletin PD-21093 09/05 Electrical Characteristics @ TJ = 25°C (unless otherwise specified) Parameters VBR, Vr VF Breakdown Voltage, Blocking Voltage Forward Voltage Min Typ Max Units Test Conditions 200 12 8.0 1.0 0.96 1.2 1.13 5 250 V V V V V µA µA pF nH IR = 100µA IF = 3A IF = 3A, TJ = 125°C IF = 6A IF = 6A, TJ = 125°C VR = VR Rated TJ = 125°C, VR = VR Rated VR = 200V Measured lead to lead 5mm from package body . IR Reverse Leakage Current - CT LS Junction Capacitance Series Inductance - Dynamic Recovery Characteristics @ TJ = 25°C (unless otherwise specified) Parameters trr Reverse Recovery Time Min Typ Max Units Test Conditions - 19 26 35 25 - ns IF = 1.0A, diF/dt = 50A/µs, VR = 30V IF = 0.5A, I R = 1.0A, IREC = 0.25A TJ = 25°C TJ = 125°C IF = 3A VR = 160V diF /dt = 200A/µs IRRM Peak Recovery Current - 3.1 4.6 30 60 - A T J = 25°C TJ = 125°C Qrr Reverse Recovery Charge - nC T J = 25°C TJ = 125°C Thermal - Mechanical Characteristics Parameters TJ TStg RthJC RthJA RthCS Wt Max. Junction Temperature Range Max. Storage Temperature Range Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient Thermal Resistance, Case to Heatsink Weight Per Leg Per Leg Min - 65 - 65 - Typ 0.3 0.01 - Max 175 175 9.0 80 12 10 Units °C °C/ W g (oz) Kg-cm lbf.in Mounting Torque 6.0 5.0 Marking Device Mounting Surface, Flat, Smooth and Greased MURD620CT 2 www.irf.com MURD620CTPbF Bulletin PD-21093 09/05 100 100 T J = 175˚C Reverse Current - I R (µA) 10 150˚C 125˚C 100˚C 1 0.1 10 Instantaneous Forward Current - I F (A) 0.01 25˚C 0.001 T = 175˚C J J J 0 50 100 150 200 Reverse Voltage - VR (V) Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage T = 150˚C T = 25˚C Junction Capacitance - C T (pF) 100 T = 25˚C J 1 0.1 0 0.2 0.4 0.6 0.8 1 1.2 1.4 Forward Voltage Drop - VFM (V) 1.6 10 1 10 100 1000 Reverse Voltage - VR (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage Fig. 1 - Typical Forward Voltage Drop Characteristics 10 Thermal Impedance Z thJC (°C/W) D = 0.50 D = 0.20 1 D = 0.10 D = 0.05 D = 0.02 D = 0.01 PDM t1 t2 Notes: 1. Duty factor D = t1 /t2 2. Peak Tj = Pdm x ZthJC + Tc 0.1 Single Pulse (Thermal Resistance) 0.01 0.00001 0.0001 0.001 0.01 0.1 1 t1, Rectangular Pulse Duration (Seconds) Fig. 4 - Max. Thermal Impedance Z thJC Characteristics www.irf.com 3 MURD620CTPbF Bulletin PD-21093 09/05 180 Allowable Case Temperature (°C) 4.5 Average Power Loss ( Watts ) 4 3.5 3 2.5 2 1.5 1 0.5 0 0 1 2 3 4 5 Average Forward Current - IF(AV) (A) D = 0.01 D = 0.02 D = 0.05 D = 0.10 D = 0.20 D = 0.50 DC RMS Limit 170 160 DC 150 140 Rated Vr applied 130 see note (2) Square wave (D = 0.50) 120 0 1 2 3 4 5 Average Forward Current - IF(AV) (A) Fig. 5 - Max. Allowable Case Temperature Vs. Average Forward Current Fig. 6 - Forward Power Loss Characteristics 50 140 V R= 30V T J = 125˚C T J = 25˚C 120 40 IF = 3 A IF = 6 A 100 IF = 6 A IF = 3 A trr ( nC ) 30 Qrr ( nC ) V R= 30V T J = 125˚C T J = 25˚C 80 60 40 20 20 10 100 1000 0 100 1000 di F /dt (A/µs ) Fig. 7 - Typical Reverse Recovery vs. di F /dt di F /dt (A/µs ) Fig. 8 - Typical Stored Charge vs. di F /dt (2) Formula used: T C = T J - (Pd + PdREV) x R thJC ; Pd = Forward Power Loss = I F(AV) x V FM @ (IF(AV) / D) (see Fig. 6); Pd REV = Inverse Power Loss = V R1 x IR (1 - D); I R @ VR1 = rated V R 4 www.irf.com MURD620CTPbF Bulletin PD-21093 09/05 Reverse Recovery Circuit VR = 200V 0.01 Ω L = 70µH D.U.T. di F / dif/dtdt ADJUST G D IRFP250 S Fig. 9- Reverse Recovery Parameter Test Circuit 3 IF 0 t rr ta tb 4 2 Q rr I RRM 0.5 I RRM di(rec)M/dt 0.75 I RRM 5 1 /dt di fF/dt 1. diF/dt - Rate of change of current through zero crossing 2. IRRM - Peak reverse recovery current 3. trr - Reverse recovery time measured from zero crossing point of negative going IF to point where a line passing through 0.75 IRRM and 0.50 IRRM extrapolated to zero current 4. Qrr - Area under curve defined by t rr and IRRM t rr x I RRM Q rr = 2 5. di (rec)M /dt - Peak rate of change of current during t b p ortion of t rr Fig. 10 - Reverse Recovery Waveform and Definitions www.irf.com 5 MURD620CTPbF Bulletin PD-21093 09/05 Outline Table 2.38 (0.09) 6.73 (0.26) 6.35 (0.25) 5.46 (0.21) 5.21 (0.20) 4 2.19 (0.08) 1.27 (0.05) 0.88 (0.03) 1.14 (0.04) 0.89 (0.03) 0.58 (0.02) 0.46 (0.02) MINIMUM RECOMMENDED FOOTPRINT 5.97 (0.24) 6.45 (0.24) 6.22 (0.24) 1.64 (0.02) 1 2 3 5.68 (0.22) 10.42 (0.41) 9.40 (0.37) 0.51 (0.02) MIN. 6.48 (0.26) 10.67 (0.42) 5.97 (0.23) 1.52 (0.06) 1.15 (0.04) 2x 1.14 (0.04) 0.76 (0.03) 2.28 (0.09) 2x 4.57 (0.18) 3x 0.89 (0.03) 0.64 (0.02) 1 2 3 4 - Anode - Cathode - Anode - Cathode 2x 2.54 (0.10) 1.65 (0.06) 2x Base Common Cathode 4 0.58 (0.02) 0.46 (0.02) 2.28 (0.09) 2x Conform to JEDEC outline D-Pak (Similar to TO-252AA) Dimensions in millimeters and (inches) 2 Common 1 Cathode 3 Anode Anode Part Marking Information PART NUMBER MURD620CT THIS IS A MURD620CT INTERNATIONAL RECTIFIER LOT CODE 8024 LOGO ASSEMBLED ON WW 02, 2003 ASSEMBLY LOT CODE DATE CODE P = LEAD-FREE YEAR 3 = 2003 WEEK 02 X = SITE ID 6 www.irf.com MURD620CTPbF Bulletin PD-21093 09/05 Tape & Reel Information 4.1 (0.16) 3.9 (0.15) TR 2.1 (0.83) 1.9 (0.07) 1.85 (0.07) DIA. 1.65 (0.06) 1.85 (0.07) 1.65 (0.06) 7.6 (0.30) 7.4 (0.29) 12.1 (0.48) 11.9 (0.47) 2.6 (0.10) DIA. 1.5 (0.06) 0.35 (0.01) 0.25 (0.01) 16.3 (0.64) 15.7 (0.62) 7.0 (0.28) 6.8 (0.26) 2.75 (0.11) 2.55 (0.10) FEED DIRECTION 4.1 (0.16) 3.9 (0.15) TRR 2.1 (0.83) 1.9 (0.07) 1.85 (0.07) DIA. 1.65 (0.06) 1.85 (0.07) 1.65 (0.06) 7.6 (0.30) 7.4 (0.29) 0.35 (0.01) 0.25 (0.01) 10.6 (0.42) 10.4 (0.41) 2.75 (0.11) 2.55 (0.10) 16.3 (0.64) 15.7 (0.62) FEED DIRECTION 8.1 (0.32) 7.9 (0.31) 2.6 (0.10) DIA. 1.5 (0.06) 1.85 (0.07) DIA. 1.65 (0.06) 1.85 (0.07) 1.65 (0.06) 7.6 (0.30) 7.4 (0.29) 4.1 (0.16) 3.9 (0.15) TRL 2.1 (0.83) 1.9 (0.07) 0.35 (0.01) 0.25 (0.01) 16.3 (0.64) 15.7 (0.62) 10.6 (0.42) 10.4 (0.41) 2.75 (0.11) 2.55 (0.10) FEED DIRECTION 8.1 (0.32) 7.9 (0.31) 2.6 (0.10) DIA. 1.5 (0.06) 13 (0.52) DIA. 22.4 (0.88) TO-252AA Tape & Reel D-Pak Tape & Reel When ordering, indicate the part number, part orientation, and the quantity. Quantities are in multiples of 2,000 pieces per reel for TR and multiples of 3,000 pieces per reel for both TRL and TRR. 375 (14.17) DIA. MAX. 50 (1.97) DIA. www.irf.com 7 MURD620CTPbF Bulletin PD-21093 09/05 Ordering Information Table Device Code MUR 1 D 2 6 3 20 4 CT TRL PbF 5 6 7 1 2 3 4 5 6 7 - Ultrafast MUR Series D = D-Pak Current Rating (6 = 6A) Voltage Rating (20 = 200V) CT = Center Tap (Dual) TR = Tape & Reel TRL = Tape & Reel (Left Oriented) TRR = Tape & Reel (Right Oriented) Tape & Reel Suffix none = Standard Production PbF = Lead-Free Data and specifications subject to change without notice. This product has been designed and qualified for Consumer Level and Lead-Free. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 2 33 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 09/05 8 www.irf.com