RDHA720SF06A1NK

PD-96960B Radiation Hardened, Solid-State Relay Product Summary Part Number RDHA720SF06A1NK RDHA720SF06A1NK 60V, 20A Current 20A e Breakdown Voltage 60V tr / tf Fast 5-PIN SURFACE MOUNT Description The RDHA720SF06A1NK is a radiation hardened solid-state relay in a hermetic package. It is configured as a single-pole-single-throw (SPST) normally open relay. This device is characterized for 100 krad(Si) total ionizing dose. The RDHA720SF06A1NK is optically coupled and actuated by an input current. Features: n n n n Total Dose Capability to 100krad(Si) Optically Coupled 1000VDC Input to Output Isolation Hermetically Sealed Package Absolute Maximum Ratings @ Tj=25°C (unless otherwise specified) Output Supply Voltage Output Current d,e e Parameter Symbol VS IO IDD IDD pk PDISS TJ TS TL Value 60 20 50 100 150 -55 to +125 -65 to +150 300 Units V A mA W °C Input Supply Current Peak Input Supply Current (t ≤1ms) Power Dissipation , Operating Temperature Range Storage Temperature Range Lead Temperature de For notes, please refer to page 3 www.irf.com 1 03/29/06 RDHA720SF06A1NK General Characteristics @ -55°CdTCd+125°C (Unless Otherwise Specified) Parameter Input Supply Current Input Voltage Drop Group A Subgroups 1 1 Test Conditions IO = 20A IIN = 10mA VI-O = 1.0KVdc, dwell = 5.0s IDD ≤ 0.5mA, f =1.0MHz, V+= 25V TC = 25°C IDD = 20mA MIL-HDBK-217F, SF@Tc= 25°C Symbol Min. Typ. Max. Units IDD VL II-O COSS RTHJC 12 4.0 ---4.4 20 5.2 -2000 --40 6.4 1.0 -0.65 -mA V µA pF °C/W MHrs c Input-to-Output Leakage Current c Thermal Resistancec,d Output Capacitance MTBF Pre-Irradiation Electrical Characteristics @ -55°CdTCd+125°C (Unless Otherwise Specified) Parameter Group A Subgroups Output On-Resistance Output Leakage Current Turn-On Delay Turn-Off Delay Rise Time Fall Time 1 2 1 2 1,2,3 1,2,3 1,2,3 1,2,3 IDD = 20mA, IO= 20A IDD ≤ 0.5mA, VOUT = 60V IDD ≤ 0.5mA, VOUT = 48V IDD = 20mA, VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% IDD = 20mA, VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% RDS(ON) IO ton toff tr tf Test Conditions Symbol Min. Typ. Max. Units --------0.030 0.040 0.045 0.078 -25 -0.65 0.2 0.85 0.06 250 1.25 0.5 ms 1.65 0.15 Ω µA f f f f For notes, please refer to page 3 2 www.irf.com RDHA720SF06A1NK Post Total Dose Irradiation Electrical Characteristics @ 25°C (Unless Otherwise Specified)g,h,i Parameter Output On-Resistance Output Leakage Current Turn-On Delay Turn-Off Delay Rise Time Fall Time Group A Subgroups 1 1 1 1 1 1 Test Conditions IDD = 20mA, IO = 20A IDD ≤ 0.5mA, VOUT = 60V IDD = 20mA, VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% IDD = 20mA, VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% VS = 40V, IO = 20A PW = 4.0ms, D ≤ 1% Symbol Min. Typ. Max. Units RDS(ON) IO ton toff tr tf ------- 0.03 0.040 -0.8 0.05 1.1 0.06 25 1.6 0.13 Ω µA f f f ms 2.2 0.15 f Notes for Maximum Rating, Electrical and General Characteristic Tables  Specification is guaranteed by design ‚ Optically coupled Solid State Relays (SSRs) have relatively slow turn on and turn off times. Care must be taken to insure that transient currents do not cause violation of SOA. If transient conditions are present, IR recommends a complete simulation to be performed by the end user to ensure compliance with SOA requirements as specified in the IRHN7054 data sheet ƒ While the SSR design meets the design requirements specified in MIL-PRF-38534, the end user is responsible for product derating, as required for the application m Reference Figures 3 & 4 for Switching Test Circuit and Wave Form n Total Dose Irradiation with Input Bias 20mA IDD applied and VDS = 0 during Irradiation o Total Dose Irradiation with Output Bias 48 Volts VDS applied and IDD = 0 during Irradiation ‡ International Rectifier does not currently have a DSCC certified Radiation Hardness Assurance Program www.irf.com 3 RDHA720SF06A1NK 25 20 ( ID, Drain Current (A) 15 10 D 5 0 25 50 75 100 125 150 TC, Case Temperature (°C) Fig 1: Maximum Drain Current Vs Case Temperature Fig 2: Typical Application Radiation Performance International Rectifier Radiation Hardened SSRs are tested to verify their hardness capability. The hardness assurance program at IR uses a Cobalt-60 (60Co) Source and heavy ion irradiation. Both pre- and postirradiation performance are tested and specified using the same drive circuitry and test conditions to provide a direct comparison. 4 www.irf.com RDHA720SF06A1NK Fig 3: Switching Test Circuit Fig 4: Switching Test Waveform www.irf.com 5 RDHA720SF06A1NK Case Outline and Dimensions — 5-Pin Surface Mount Package Pin Assignment Pin # 1 2 3 4 5 Pin Description N/C DRAIN SOURCE PHOTO DIODE ANODE PHOTO DIODE CATHODE Notes 1. 2. 3. 4. Dimensioning and Tolerancing per ASME Y14.5SM-1994 Controlling Dimension: Inch Dimensions are shown in inches Tolerances are +/- 0.005 UOS Device Type Part Numbering Nomenclature RD H A 7 20 SF 06 A 1 N K Screening Level K = Class K per MIL-PRF-38534 RD = DC Solid State Relay Radiation Characterization H = RAD Hard Features N = Non Buffered Fast Generation A = Current Design Radiation Level 7 = 100K Rad (Si) Poles 1 = Single Pole Current 20 = 20A Throw Configuration A = Single Throw, Normally Open Package SF = 5-Pin Surface Mount Volts 06 = 60 Volts IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 IR LEOMINSTER : 205 Crawford St., Leominster, Massachusetts 01453, USA Tel: (978) 534-5776 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. Data and specifications subject to change without notice. 03/2006 6 www.irf.com