6N137SMT/R

ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 DESCRIPTION The 6N137, ICPL2601 and ICPL2611 devices each consist of an infrared emitting diode, optically coupled to a high speed integrated photo detector logic gate with a strobable output. 1 2 3 4 5 6 7 8 FEATURES • • • • • • • • High Speed 10Mbit/s Minimum Common Mode Transient Immunity 10kV/μs for ICPL2611 High AC Isolation Voltage 5000VRMS Guaranteed Performance from -40°C to 85°C Logic Gate Output Pb Free and RoHS Compliant UL File E91231 for ICPL2601 VDE File 40044276 marked as 6N137V APPLICATIONS • • • • • • • Line Receivers, Data Communication LSTTL to TTL, LSTTL or 5V CMOS Data Multiplexing Pulse Transformer Replacement Switch Mode Power Supplies Ground Loop Elimination Computer Peripheral Interface ORDER INFORMATION • • • Add G after PN for 10mm lead spacing Add SM after PN for Surface Mount Add SMT&R after PN for Surface Mount Tape & Reel NC Anode Cathode NC GND VO VE VCC A 0.1μF bypass Capacitor must be connected between Pins 8 and 5. ABSOLUTE MAXIMUM RATINGS (TA = 25°C) Stresses exceeding the absolute maximum ratings can cause permanent damage to the device. Exposure to absolute maximum ratings for long periods of time can adversely affect reliability. Input Forward Current Reverse Voltage Power dissipation 50mA 5V 100mW Output Output Current Output Voltage Supply Voltage Enable Input Voltage 50mA 7.0V 7.0V 5.5V (maximum 500mV above VCC) Power Dissipation 85mW Total Package Isolation Voltage Operating Temperature Storage Temperature Lead Soldering Temperature 5000VRMS -40 to 85 °C -55 to 125 °C 260°C (10s) ISOCOM COMPONENTS 2004 LTD Unit 25B, Park View Road West, Park View Industrial Estate Hartlepool, Cleveland, TS25 1PE, United Kingdom Tel : +44 (0)1429 863 609 Fax : +44 (0)1429 863 581 e-mail : sales@isocom.co.uk http://www.isocom.com 1 28/09/2017 ISOCOM COMPONENTS ASIA LTD Hong Kong Office, Block A, 8/F, Wah Hing Industrial mansion, 36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong. Tel : +852 2995 9217 Fax : +852 8161 6292 e-mail : sales@isocom.com.hk DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 Truth Table Input Enable Output H H L L H H H L H L L H H NC L L NC H Recommended Operating Conditions Parameter Symbol Min Max Unit Operating Temperature TA - 40 85 °C Supply Voltage VCC 4.5 5.5 V Input Current, High Level IF(ON) 5 10 mA Input Current, Low Level IF(OFF) 0 250 µA Enable Voltage, High Level VEH 2.0 VCC V Enable Voltage, Low Level VEL 0 0.8 V 2 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 ELECTRICAL CHARACTERISTICS (TA = -40 to 85°C unless otherwise specified) INPUT Parameter Typ.* Max Unit IF = 10mA 1.4 1.8 V ΔVF/ΔT IF = 10mA ̶ 1.8 Reverse Voltage VR IR = 10μA Input Capacitance CIN VF = 0V, f = 1MHz Symbol Test Condition High Level Supply Current ICCH Low Level Supply Current Forward Voltage Forward Voltage Temperature Coefficient Symbol Test Condition VF Min mV/°C 5.0 V 60 pF OUTPUT Parameter Min Typ.* Max Unit IF = 0mA, VCC = 5.5V VE = 0.5V 7 10 mA ICCL IF = 10mA, VCC = 5.5V 9 13 mA High Level Output Current IOH IF = 250µA, VCC = 5.5V, VE = 2.0V, VO = 5.5V 2.1 100 µA Low Level Output Voltage VOL IF = 5mA, VCC = 5.5V, VE = 2.0V, IOL = 13mA 0.35 0.6 V High Level Enable Current IEH VCC = 5.5V, VE = 2.0V -0.6 -1.6 mA Low Level Enable Current IEL VCC = 5.5V, VE = 0.5V -0.8 -1.6 mA High Level Enable Voltage VEH IF = 10mA, VCC = 5.5V Low Level Enable Voltage VEL IF = 10mA, VCC = 5.5V Parameter Symbol Test Condition Input Threshold Current IFT VCC = 5.5V, VO = 0.6V VE = 2.0V, IOL = 13mA 2.0 V 0.8 V Typ.* Max Unit 2.5 5 mA COUPLED Min * Typical values at TA = 25°C 3 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 ELECTRICAL CHARACTERISTICS (TA = -40 to 85°C unless otherwise specified) SWITCHING (IF = 7.5mA, VCC = 5V unless otherwise specified) Parameter Symbol Test Condition Propagation Delay Time to High Output Level tPLH Propagation Delay Time to Low Output Level tPHL RL = 350Ω, CL = 15pF, TA = 25ºC Pulse Width Distortion |tPHL - tPLH| RL = 350Ω, CL = 15pF Min Typ.* Max Unit 35 75 ns 40 75 5 35 Output Rise Time (10% to 90%) tr 40 Output Fall Time (90% to 10%) tf 10 Enable Propagation Delay Time to High Output Level tELH Enable Propagation Delay Time to Low Output Level tEHL VEH = 3.5V, RL = 350Ω, CL = 15pF 15 15 * Typical values at TA = 25°C 4 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 ELECTRICAL CHARACTERISTICS (TA = -40 to 85°C unless otherwise specified) SWITCHING (IF = 7.5mA, VCC = 5V unless otherwise specified) Parameter Common Mode Transient Immunity at Logic High Symbol CMH Test Condition Min 6N137 Typ.* Max Unit 5000 V/μs 5000 V/μs IF = 0mA, VOH = 2.0V, RL = 350Ω, VCM = 10Vp-p, TA = 25°C ICPL2601 5000 IF = 0mA, VOH = 2.0V, RL = 350Ω, VCM = 50Vp-p, TA = 25°C ICPL2611 10000 IF = 0mA, VOH = 2.0V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C ICPL2611 20000 High CMR Test Circuit IF = 0mA, VOH = 2.0V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C Common Mode Transient Immunity at Logic Low CML 6N137 IF = 7.5mA, VOL = 0.8V, RL = 350Ω, VCM = 10Vp-p, TA = 25°C ICPL2601 5000 IF = 7.5mA, VOL = 0.8V, RL = 350Ω, VCM = 50Vp-p, TA = 25°C ICPL2611 10000 IF = 7.5mA, VOL = 0.8V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C ICPL2611 20000 High CMR Test Circuit IF = 7.5mA, VOL = 0.8V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C * Typical values at TA = 25°C 5 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 ELECTRICAL CHARACTERISTICS (TA = -40 to 85°C unless otherwise specified) ISOLATION Parameter Insulation Voltage Symbol Test Condition Min VISO RH = 40% - 60%, TA = 25°C t = 1 min, 5000 Typ.* Max Unit VRMS * Typical values at TA = 25°C Note : - VCC supply must be bypassed by a 0.1μF capacitor or larger with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins. - Enable Input – No pull up resistor required as the device has an internal pull up resistor. - tPLH is measured from the 3.75mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. - tPHL is measured from the 3.75mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. - tr Rise time is measured from the 10% to the 90% levels on the LOW to HIGH transition of the output pulse. - tf Fall time is measured from the 90% to the 10% levels on the HIGH to LOW transition of the output pulse. - tELH is measured from the 1.5V level on the HIGH to LOW transition of the input Enable voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse. - tEHL is measured from the 1.5V level on the LOW to HIGH transition of the input Enable voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse. - CMH – The maximum tolerable rate of rise of the Common Mode voltage to ensure the output will remain in the HIGH state (i.e., VO > 2.0V). - CML – The maximum tolerable rate of rise of the Common Mode voltage to ensure the output will remain in the LOW output state (i.e., VO < 0.8V). 6 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 Fig 1 Forward Current vs Forward Voltage Fig 2 Input Threshold Current vs TA Fig 3 Output Voltage vs Forward Current Fig 4 Output Low Level Voltage vs TA Fig 5 Output High Level Current vs TA Fig 6 Output Low Level Current vs TA 7 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 Fig 7 Propagation Delay vs Forward Current Fig 9 Rise / Fall Time vs TA Fig 8 Propagation Delay vs TA Fig 10 Pulse Width Distortation vs TA Fig 11 Enable Propagation Delay vs TA 8 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 tr, tf, tPLH and tPHL Test Circuit CMR Test Circuit 9 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 VCM 0V 5V VO Pos. A, IF = 0mA CMH VO(Min) VO(Max) VO Pos. B, IF = 7.5mA CML 0.5V CMR Test Circuit High CMR Test Circuit for ICPL2611 10 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 ORDER INFORMATION UL Approval PN After PN Description Packing quantity None ICPL2601 Standard DIP8 45 pcs per tube G ICPL2601G 10mm Lead Spacing 45 pcs per tube SM ICPL2601SM Surface Mount 45 pcs per tube SMT&R ICPL2601SMT&R Surface Mount Tape & Reel 1000 pcs per reel UL and VDE Approvals PN After PN Description Packing quantity None 6N137 Standard DIP8 45 pcs per tube G 6N137G 10mm Lead Spacing 45 pcs per tube SM 6N137SM Surface Mount 45 pcs per tube SMT&R 6N137SMT&R Surface Mount Tape & Reel 1000 pcs per reel Safety Approval Pending PN After PN Description Packing quantity None ICPL2611 Standard DIP8 45 pcs per tube G ICPL2611G 10mm Lead Spacing 45 pcs per tube SM ICPL2611SM Surface Mount 45 pcs per tube SMT&R ICPL2611SMT&R Surface Mount Tape & Reel 1000 pcs per reel 11 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 DEVICE MARKING Example : 6N137 6N137V IYWW 6N137V denotes Device Part Number I denotes Isocom Y denotes 1 digit Year code WW denotes 2 digit Week code 12 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 PACKAGE DIMENSIONS (mm) DIP G-Form 13 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 PACKAGE DIMENSIONS (mm) SMD RECOMMENDED PAD LAYOUT FOR SMD (mm) 14 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 TAPE AND REEL PACKAGING Direction of feed from reel Dimension No. A B D0 D1 E F Dimension( mm) 10.4±0.1 10.0±0.1 1.5±0.1 1.5±0.1 1.75±0.1 7.5±0.1 Dimension No. P0 P1 P2 t W K Dimension (mm) 4.0±0.1 12.0±0.1 2.0±0.1 0.4±0.1 16.0 ±0.3 / -0.1 4.5±0.1 15 28/09/2017 DD93209 ISOCOM COMPONENTS 6N137, ICPL2601, ICPL2611 IR REFLOW SOLDERING TEMPERATURE PROFILE One Time Reflow Soldering is Recommended. Do not immerse device body in solder paste. TP 260°C TP - 5°C Max Ramp Up Rate 3°C/s TEMP (°C) TL Tsmax Tsmin tP Max Ramp Down Rate 6°C/s 217°C TL 200°C 150°C ts Preheat 60s – 120s 25°C TIME (s) Time 25°C to Peak Temperature Profile Details Conditions Preheat - Min Temperature (TSMIN) - Max Temperature (TSMAX) - Time TSMIN to TSMAX (ts) 150°C 200°C 60s - 120s Soldering Zone - Peak Temperature (TP) - Time at Peak Temperature - Liquidous Temperature (TL) - Time within 5°C of Actual Peak Temperature (TP ̶ 5°C) - Time maintained above TL (tL) - Ramp Up Rate (TL to TP) - Ramp Down Rate (TP to TL) 260°C 10s max 217°C 30s max 60s - 100s 3°C/s max 6°C/s max Average Ramp Up Rate (Tsmax to TP) 3°C/s max Time 25°C to Peak Temperature 8 minutes max 16 28/09/2017 DD93209 ISOCOM COMPONENTS DISCLAIMER Isocom Components is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing Isocom Components products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such Isocom Components products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that Isocom Components products are used within specified operating ranges as set forth in the most recent Isocom Components products specifications. The Isocom Components products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These Isocom Components products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation Instruments, traffic signal instruments, combustion control instruments, medical Instruments, all types of safety devices, etc... Unintended Usage of Isocom Components products listed in this document shall be made at the customer’s own risk. Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with domestic garbage. The products described in this document are subject to the foreign exchange and foreign trade laws. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Isocom Components for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of Isocom Components or others. The information contained herein is subject to change without notice. 17 28/09/2017 DD93209