ICPL2531SM

ISOCOM COMPONENTS ICPL2530, ICPL2531 DESCRIPTION The ICPL2530 and ICPL2531 dual channel devices each consists of an infrared emitting diode optically coupled to a high speed photo detector transistor. A separate connection for the photodiode bias and output transistor collector increases the speed by several orders of magnitude over conventional phototransistor couplers by reducing the base-collector capacitance. 1. Anode 2. Cathode 3. Cathode 4. Anode 5. Gnd 6. Vout2 7. Vout1 8. VCC FEATURES • • • • • • High Speed 1Mbit/s High AC Isolation Voltage 5000VRMS Guaranteed Performance from 0°C to 70°C Wide Operating Temperature Range -40°C to 100 °C Pb Free and RoHS Compliant Safety Approvals Pending APPLICATIONS • • • • • Line Receivers Telecommunication Equipment Power Transistor Isolation in Motor Drives Replacement of Low Speed Phototransistor Optocouplers High Speed Logic Ground Isolation ORDER INFORMATION • • • Add G after PN for 10mm lead spacing Add SM after PN for Surface Mount Add SMT&R after PN for Surface Mount Tape & Reel . ISOCOM COMPONENTS 2004 LTD Unit 25B, Park View Road West, Park View Industrial Estate Hartlepool, Cleveland, TS25 1UD, United Kingdom Tel: +44 (0)1429 863 609 Fax : +44 (0)1429 863 581 e-mail: sales@isocom.co.uk http://www.isocom.com 1 23/07/2013 ABSOLUTE MAXIMUM RATINGS Input Diode Forward Current Peak Forward Current (50% duty cycle 1ms pulse width) Peak Transient Current (≤ 1μs pulse width, 300pps) Reverse Voltage Power dissipation 25mA 50mA 1A 5V 45mW Output Average Output Current Peak Output Current Output Voltage Supply Voltage Power Dissipation 8mA 16mA -0.5 to 20V -0.5 to 30V 35mW Total Package Isolation Voltage Operating Temperature Storage Temperature Lead Soldering Temperature (10s) 5000VRMS -40 to 100 °C -55 to 125 °C 260°C ISOCOM COMPONENTS ASIA LTD Hong Kong Office, Block A, 8/F, Wah Hing Industrial mansion, 36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong. Tel: +852 2995 9217 Fax : +852 8161 6292 e-mail sales@isocom.com.hk Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 ELECTRICAL CHARACTERISTICS INPUT (TA = 0°C to 70°C unless otherwise specified) Parameter Symbol Test Condition Forward Voltage VF IF = 16mA, TA = 25°C Reverse Voltage VR IR = 10µA VF/TA IF = 16mA -1.9 mV/°C CIN VF = 0V, f = 1MHz 60 pF Temperature Coefficient Input Capacitance Min Typ.* Max Unit 1.45 1.8 V 5.0 V OUTPUT (TA = 0°C to 70°C unless otherwise specified) Parameter Logic High Output Current Symbol Test Condition IOH IF = 0mA, VO = VCC = 5.5V, TA = 25°C Min Typ.* Max Unit 0.001 0.5 µA IF = 0mA, VO = VCC = 15V, TA = 25°C 50 Logic Low Supply Current ICCL IF1 = IF2 = 16mA, VO = Open, VCC = 15V 140 400 µA Logic High Supply Current ICCH IF = 0mA, VO = Open VCC = 15V, TA = 25°C 0.01 1 µA IF = 0mA, VO = Open VCC = 15V 4 * Typical Values at TA = 25°C 2 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 ELECTRICAL CHARACTERISTICS COUPLED (TA = 0°C to 70°C unless otherwise specified) Parameter Symbol Current Transfer Ratio CTR Logic Low Output Voltage VOL Test Condition Min ICPL2530 ICPL2531 IF = 16mA, VO = 0.4V VCC = 4.5V, TA = 25°C 7 19 ICPL2530 ICPL2531 IF = 16mA, VO = 0.5V VCC = 4.5V 5 15 Typ.* Max Unit 50 50 % % ICPL2530 IF = 16mA, IO = 1.1mA VCC = 4.5V, TA = 25°C 0.18 0.5 V ICPL2531 IF = 16mA, IO = 3mA VCC = 4.5V, TA = 25°C 0.25 0.5 V ICPL2530 IF = 16mA, IO = 0.8mA VCC = 4.5V 0.5 V ICPL2531 IF = 16mA, IO = 2.4mA VCC = 4.5V 0.5 V * Typical Values at TA = 25°C 3 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 ELECTRICAL CHARACTERISTICS Switching Characteristics (TA = 0°C to 70°C, Vcc = 5V, IF = 16mA unless otherwise specified) Parameter Propagation Delay Time to Logic Low Propagation Delay Time to Logic High Common Mode Transient Immunity at Logic High Common Mode Transient Immunity at Logic Low Symbol tPHL tPLH CMH CML Test Condition Min Typ.* Max ICPL2530 RL = 4.1kΩ, TA = 25°C RL = 4.1kΩ 0.35 1.5 2.0 ICPL2531 RL = 1.9kΩ, TA = 25°C RL = 1.9kΩ 0.35 0.8 1.0 ICPL2530 RL = 4.1kΩ, TA = 25°C RL = 4.1kΩ 0.5 1.5 2.0 ICPL2531 RL = 1.9kΩ, TA = 25°C RL = 1.9kΩ 0.3 0.8 1.0 Unit μs μs ICPL2530 IF = 0mA, VCM = 10Vp-p, RL = 4.1kΩ , TA = 25°C 1000 10000 V/μs ICPL2531 IF = 0mA, VCM = 1000Vp-p, RL = 1.9kΩ , TA = 25°C 1000 10000 V/μs ICPL2530 IF = 16mA, VCM = 10Vp-p, RL = 4.1kΩ , TA = 25°C 1000 10000 V/μs ICPL2531 IF = 16mA, VCM = 1000Vp-p, RL = 1.9kΩ , TA = 25°C 1000 10000 V/μs * Typical Values at TA = 25°C - Common mode transient immunity in logic high level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e. VO > 2.0V). - Common mode transient immunity in logic low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e. VO < 0.8V). 4 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 Fig 1 Forward Current vs Forward Voltage Fig 2 Output Current vs Output Voltage Fig 3 Normalized CTR vs Forward Current Fig 4 Normalized CTR vs Ambient Temperature Fig 5 Propagation Delay vs Load Resistance Fig 6 Propagation Delay vs Ambient Temperature 5 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 Fig 7 Logic High Output Current vs TA Pulse Generator tr = 5ns ZO = 50Ω 10% Duty Cycle 1/f < 100μs Fig 8 Switching Time Test Circuit Fig 9 Transient Immunity Test Circuit 6 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 ORDER INFORMATION ICPL2530 After PN PN Description Packing quantity None ICPL2530 Standard DIP8 45 pcs per tube G ICPL2530G 10mm Lead Spacing 45 pcs per tube SM ICPL2530SM Surface Mount 45 pcs per tube SMT&R ICPL2530SMT&R Surface Mount Tape & Reel 1000 pcs per reel ICPL2531 After PN PN Description Packing quantity None ICPL2531 Standard DIP8 45 pcs per tube G ICPL2531G 10mm Lead Spacing 45 pcs per tube SM ICPL2531SM Surface Mount 50 pcs per tube SMT&R ICPL2531SMT&R Surface Mount Tape & Reel 1000 pcs per reel 7 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 PACKAGE DIMENSIONS (mm) DIP G FORM SMD 8 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 RECOMMENDED PAD LAYOUT FOR SMD (mm) REFLOW SOLDERING TEMPERATURE PROFILE 260 °C (peak,10s Max) >255 °C (30s Max) 217°C TEMP (°C) 200°C 60s – 120 s 150°C 60s – 100s 1-3 °C/s Max TIME (s) 9 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 TAPE AND REEL PACKAGING Dimension A B D0 D1 E F (mm) 10.4±0.1 10.0±0.1 1.5±0.1 1.5±0.1 1.75±0.1 7.5±0.1 Dimension P0 P1 P2 t W K (mm) 4.0±0.1 12.0±0.1 2.0±0.1 0.4±0.1 16.0 +0.3/-0.1 4.5±0.1 10 23/07/2013 Dxxxxxx ISOCOM COMPONENTS ICPL2530, ICPL2531 NOTES : - Isocom is continually improving the quality, reliability, function or design and Isocom reserves the right to make changes without further notices. - The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio/visual equipment, electrical application and instrumentation. - For equipment/application where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc., please contact our sales representatives. - When requiring a device for any ”specific” application, please contact our sales for advice. - The contents described herein are subject to change without prior notice. - Do not immerse device’s body in solder paste. 11 23/07/2013 Dxxxxxx