ICPL4503

ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 1. NC DESCRIPTION The 6N135, 6N136, ICPL4502 and ICPL4503 devices each consist of an infrared emitting diode, optically coupled to a high speed photo detector transistor. A separate connection for the photodiode bias and output-transistor collector increase the speed by several orders of magnitude over conventional phototransistor couplers by reducing the base-collector capacitance of the input transistor. 2. Anode 1 8 1 8 2 7 2 7 3 6 3 6 4 5 4 5 3. Cathode 4. NC 5. Gnd 6. Vout 7. VB (6N135/6N136) NC (ICPL4502/ ICPL4503) 6N135 / 6N136 FEATURES • • • • • • High speed 1Mbit/s High AC Isolation Voltage 5000Vrms Guaranteed performance from 0°C to 70°C Wide Operating temperature range -55°C to 100°C Pb Free and RoHS Compliant Safety Approvals Pending APPLICATIONS • • • • • • • Line Receivers Telecommunication Equipments Power Transistor Isolation in Motor Drives Replacement of Low Speed Phototransistor Optocouplers Feedback Loop in Switch Mode Power Supplies High Speed Logic Ground Isolation Home Appliances ORDER INFORMATION • • • Add G after PN for 10mm lead spacing Add SM after PN for Surface Mount, Add SMT&R after PN for Surface Mount Tape & Reel . ICPL4502 / ICPL4503 ABSOLUTE MAXIMUM RATINGS (TA = 25°C) Input Diode Forward Current Peak Forward Current (50% duty cycle, 1ms pulse width) Peak Transient Current (≤1μs pulse width, 300pps) Reverse Voltage Power dissipation http://www.isocom.com 1 17/10/13 25mA 50mA 1A 5V 45mW Output Output Current Peak Output Current Emitter-Base Reverse Voltage (6N135 and 6N136 only) Base Current (6N135 and 6N136 only) Output Voltage Supply Voltage Power Dissipation 8mA 16mA 5V 5mA -0.5 to 20V -0.5 to 30V 100mW Total Package Isolation Voltage Operating Temperature Storage Temperature Lead Soldering Temperature (10s) ISOCOM COMPONENTS 2004 LTD Unit 25B, Park View Road West, Park View Industrial Estate Hartlepool, Cleveland, TS25 1UD, United Kingdom Tel: +44 (0)1429 863 609 Fax : +44 (0)1429 863 581 e-mail: sales@isocom.co.uk 8. VCC 5000Vrms -55 to 100 °C -55 to 125 °C 260°C ISOCOM COMPONENTS ASIA LTD Hong Kong Office, Block A, 8/F, Wah Hing Industrial mansion, 36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong. Tel: +852 2995 9217 Fax : +852 8161 6292 e-mail sales@isocom.com.hk DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 ELECTRICAL CHARACTERISTICS (TA = 0°C to 70°C unless otherwise specified) INPUT Parameter Symbol Test Condition Forward Voltage VF IF = 16mA Reverse Voltage VR IR = 10µA Temperature Coefficient of VF ΔVF/ΔTA IF = 16mA Symbol Test Condition IOH Min Typ.* Max Unit 1.45 1.8 V 5.0 V -1.9 mV/°C OUTPUT Parameter Logic High Output Current Min Typ.* Max Unit IF = 0mA, VO = VCC = 5.5V, TA = 25°C 0.001 0.5 μA IF = 0mA, VO = VCC = 15V, TA = 25°C 0.01 1 IF = 0mA, VO = VCC = 15V 50 Logic Low Supply Current ICCL IF = 16mA, VO = Open, VCC = 15V 140 200 μA Logic High Supply Current ICCH IF = 0mA, VO = Open, VCC = 15V, TA = 25°C 0.01 1 μA IF = 0mA, VO = Open, VCC = 15V 2 * Typical values at TA = 25°C 2 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 ELECTRICAL CHARACTERISTICS (TA = 0°C to 70°C unless otherwise specified) COUPLED Parameter Symbol Test Condition Min Current Transfer Ratio CTR 6N135 6N136 / ICPL4502 / ICPL4503 7 19 Typ.* Max Unit 50 50 % 0.18 0.4 V 0.25 0.4 IF = 16mA, VO = 0.4V VCC = 4.5V, TA = 25°C 6N135 6N136 / ICPL4502 / ICPL4503 5 15 IF = 16mA, VO = 0.5V VCC = 4.5V Logic Low Output Voltage VOL 6N135 IF = 16mA, IO = 1.1mA, VCC = 4.5V, TA = 25°C 6N136 / ICPL4502 / ICPL4503 IF = 16mA, IO = 3mA, VCC = 4.5V, TA = 25°C 6N135 0.5 IF = 16mA, IO = 0.8mA, VCC = 4.5V 6N136 / ICPL4502 / ICPL4503 0.5 IF = 16mA, IO = 2.4mA, VCC = 4.5V * Typical values at TA = 25°C 3 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 ELECTRICAL CHARACTERISTICS (TA = 0°C to 70°C unless otherwise specified) Switching Characteristics (TA = 0°C to 70°C, IF = 16mA, VCC = 5V unless otherwise specified) Parameter Propagation Delay Time to Logic Low Symbol TPHL Test Condition Min Typ.* Max Unit μs 6N135 RL = 4.1kΩ, TA = 25°C RL = 4.1kΩ 0.35 1.5 2.0 0.35 0.8 1.0 6N136 / ICPL4502 / ICPL4503 RL = 1.9kΩ, TA = 25°C RL = 1.9kΩ Propagation Delay Time to Logic High TPLH μs 6N135 RL = 4.1kΩ, TA = 25°C RL = 4.1kΩ 0.5 1.5 2.0 6N136 / ICPL4502 / ICPL4503 RL = 1.9kΩ, TA = 25°C RL = 1.9kΩ Common Mode Transient Immunity at Logic High CMH 6N135 0.8 1.0 1000 V/μs IF = 0mA, VCM = 10Vp-p, RL = 4.1kΩ, TA = 25°C 6N136 / ICPL4502 1000 IF = 0mA, VCM = 10Vp-p, RL = 1.9kΩ, TA = 25°C ICPL4503 15000 20000 IF = 0mA, VCM = 1500Vp-p, RL = 1.9kΩ, TA = 25°C Common Mode Transient Immunity at Logic Low CML 6N135 1000 V/μs IF = 16mA, VCM = 10Vp-p, RL = 4.1kΩ, TA = 25°C 6N136 / ICPL4502 1000 IF = 16mA, VCM = 10Vp-p, RL = 1.9kΩ, TA = 25°C ICPL4503 15000 20000 IF = 16mA, VCM = 1500Vp-p, RL = 1.9kΩ, TA = 25°C * Typical values at TA = 25°C 4 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 Fig 1 Forward Current vs Forward Voltage Fig 2 Output Current vs Output Voltage Fig 3 Normalized CTR vs Forward Current Fig 4 Normalized CTR vs TA Fig 5 Logic High Output Current vs TA Fig 6 Propagation Delay vs TA 5 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 Fig 7 Propagation Delay vs Load Resistance   Switching Time Test Circuit 6 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 Common Mode Transient Immunity Test Circuit Note: Common mode transient immunity in logic high level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e., VO > 2.0V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO < 0.8V). 7 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 ORDER INFORMATION 6N135, 6N136, ICPL4502, ICPL4503 After PN PN Description Packing quantity None 6N135, 6N136, ICPL4502, ICPL4503 Standard Dip8 45 pcs per tube G 6N135G, 6N136G, ICPL4502G, ICPL4503G 10mm Lead Spacing 45 pcs per tube SM 6N135SM, 6N136SM, ICPL4502SM, ICPL4503SM Surface Mount 45 pcs per reel SMT&R 6N135SMT&R, 6N136SMT&R, ICPL4502SMT&R, ICPL4503SMT&R Surface Mount Tape & Reel 1000 pcs per reel 8 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 PACKAGE DIMENSIONS (mm) DIP G FORM 9 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 PACKAGE DIMENSIONS (mm) SMD RECOMMENDED PAD LAYOUT FOR SMD (mm) 10 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 REFLOW SOLDERING TEMPERATURE PROFILE (One Time Reflow Soldering is Recommended) TP 260°C TP - 5°C tP Max Ramp Down Rate 6°C/s Max Ramp Up Rate 3°C/s TL 217°C TEMP (°C) tL Tsmax Tsmin 200°C 150°C ts Preheat 60s – 120s 25°C Time 25°C to Peak Temperature TIME (s) Profile Details Conditions Preheat - Min Temperature (TSMIN) - Max Temperature (TSMAX) - Time TSMIN to TSMAX (ts) 150°C 200°C 60s - 120s Soldering Zone - Peak Temperature (TP) - Liquidous Temperature (TL) - Time within 5°C of Actual Peak Temperature (TP ̶ 5°C) - Time maintained above TL (tL) - Ramp Up Rate (TL to TP) - Ramp Down Rate (TP to TL) 260°C 217°C 30s 60s - 100s 3°C/s max 6°C/s max Average Ramp Up Rate (Tsmax to TP) 3°C/s max Time 25°C to Peak Temperature 8 minutes max 11 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 DEVICE MARKING (Example 6N136) 6N136 IYWW 6N136 Y WW I 12 17/10/13 denotes Device Part Number denotes 1 digit Year code denotes 2 digit Week code denotes Isocom DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 TAPE AND REEL PACKAGING   Direction of feed from reel   Dimension No. A B Do D1 E F Dimension( mm) 10.4±0.1 10.0±0.1 1.5±0.1 1.5±0.1 1.75±0.1 7.5±0.1 Dimension No. Po P1 P2 t W K Dimension (mm) 4.0±0.1 12.0±0.1 2.0±0.1 0.4±0.1 16.0+0.3/ -0.1 4.5±0.1 13 17/10/13 DC93159 ISOCOM COMPONENTS 6N135, 6N136, ICPL4502, ICPL4503 NOTES : - Isocom is continually improving the quality, reliability, function or design and Isocom reserves the right to make changes without further notices. - The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio/visual equipment, electrical application and instrumentation. - For equipment/application where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc., please contact our sales representatives. - When requiring a device for any ”specific” application, please contact our sales for advice. - The contents described herein are subject to change without prior notice. - Do not immerse device body in solder paste. 14 17/10/13 DC93159