IS41LV16105B-50TE

IS41LV16105B 1M x 16 (16-MBIT) DYNAMIC RAM WITH FAST PAGE MODE FEATURES • TTL compatible inputs and outputs; tristate I/O • Refresh Interval: — 1,024 cycles/16 ms • Refresh Mode: — RAS-Only, CAS-before-RAS (CBR), and Hidden • JEDEC standard pinout • Single power supply: 3.3V ± 10% • Byte Write and Byte Read operation via two CAS • Extended Temperature Range: -30 C to +85 C • Industrial Temperature Range: -40oC to +85oC • Lead-free available o o ISSI APRIL 2005 ® DESCRIPTION The ISSI IS41LV16105B is 1,048,576 x 16-bit high-performance CMOS Dynamic Random Access Memories. Fast Page Mode allows 1,024 random accesses within a single row with access cycle time as short as 20 ns per 16-bit word. The Byte Write control, of upper and lower byte, makes the IS41LV16105B ideal for use in 16-, 32-bit wide data bus systems. These features make the IS41LV16105B ideally suited for highbandwidth graphics, digital signal processing, high-performance computing systems, and peripheral applications. The IS41LV16105B is packaged in a 42-pin 400-mil SOJ and 400-mil 44- (50-) pin TSOP (Type II). KEY TIMING PARAMETERS Parameter Max. RAS Access Time (tRAC) Max. CAS Access Time (tCAC) Max. Column Address Access Time (tAA) Min. Fast Page Mode Cycle Time (tPC) VDD I/O0 I/O1 I/O2 I/O3 VDD I/O4 I/O5 I/O6 I/O7 NC NC NC WE RAS NC NC A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 GND I/O15 I/O14 I/O13 I/O12 GND I/O11 I/O10 I/O9 I/O8 NC NC LCAS UCAS OE A9 A8 A7 A6 A5 A4 GND -50 50 13 25 20 84 -60 60 15 30 25 104 Unit ns ns ns ns ns PIN CONFIGURATIONS 44(50)-Pin TSOP (Type II) 42-Pin SOJ VDD I/O0 I/O1 I/O2 I/O3 VDD I/O4 I/O5 I/O6 I/O7 NC NC WE RAS NC NC A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 GND I/O15 I/O14 I/O13 I/O12 GND I/O11 I/O10 I/O9 I/O8 NC LCAS UCAS OE A9 A8 A7 A6 A5 A4 GND Min. Read/Write Cycle Time (tRC) PIN DESCRIPTIONS A0-A9 I/O0-15 WE OE RAS UCAS LCAS VDD GND NC Address Inputs Data Inputs/Outputs Write Enable Output Enable Row Address Strobe Upper Column Address Strobe Lower Column Address Strobe Power Ground No Connection Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 1 IS41LV16105B FUNCTIONAL BLOCK DIAGRAM ISSI ® OE WE LCAS UCAS CAS CLOCK GENERATOR WE CONTROL LOGICS OE CONTROL LOGIC OE CAS WE RAS RAS CLOCK GENERATOR DATA I/O BUS REFRESH COUNTER DATA I/O BUFFERS ROW DECODER RAS COLUMN DECODERS SENSE AMPLIFIERS I/O0-I/O15 MEMORY ARRAY 1,048,576 x 16 ADDRESS BUFFERS A0-A9 2 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B TRUTH TABLE Function Standby Read: Word Read: Lower Byte Read: Upper Byte Write: Word (Early Write) Write: Lower Byte (Early Write) Write: Upper Byte (Early Write) Read-Write(1,2) Hidden Refresh RAS-Only Refresh CBR Refresh (4) ISSI RAS H L L L L L L L LCAS H L L H L L H L L L H L UCAS H L H L L H L L L L H L WE X H H H L L L H→L H L X X OE X L L L X X X L→H L X X X Address tR/tC X ROW/COL ROW/COL ROW/COL ROW/COL ROW/COL ROW/COL ROW/COL ROW/COL ROW/COL ROW/NA X I/O High-Z D OUT Lower Byte, DOUT Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DOUT DIN Lower Byte, DIN Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DIN DOUT, DIN D OUT D OUT High-Z High-Z ® Read(2) Write(1,3) L→H→L L→H→L L H→L Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. EARLY WRITE only. 4. At least one of the two CAS signals must be active (LCAS or UCAS). Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 3 IS41LV16105B Functional Description The IS41LV16105B is a CMOS DRAM optimized for highspeed bandwidth, low power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 16 address bits. These are entered ten bits (A0-A9) at a time. The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first nine bits and CAS is used the latter nine bits. The IS41LV16105B has two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generates a CAS signal functioning in an identical manner to the single CAS input on the other 1M x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 through I/O7 and UCAS controls I/O8 through I/O15. The IS41LV16105B CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IS41LV16105B both BYTE READ and BYTE WRITE cycle capabilities. ISSI Write Cycle ® A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs last. Refresh Cycle To retain data, 1,024 refresh cycles are required in each 16 ms period. There are two ways to refresh the memory. 1. By clocking each of the 1,024 row addresses (A0 through A9) with RAS at least once every 16 ms. Any read, write, read-modify-write or RAS-only cycle refreshes the addressed row. 2. Using a CAS-before-RAS refresh cycle. CAS-beforeRAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 9-bit counter provides the row addresses and the external address inputs are ignored. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Memory Cycle A memory cycle is initiated by bring RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensures proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tRAS time has expired. A new cycle must not be initiated until the minimum precharge time tRP, tCP has elapsed. Power-On After application of the VDD supply, an initial pause of 200 µs is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with VDD or be held at a valid VIH to avoid current surges. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tAR. Data Out becomes valid only when tRAC, tAA, tCAC and tOEA are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. 4 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B ABSOLUTE MAXIMUM RATINGS(1) Symbol VT VDD IOUT PD TA Parameters Voltage on Any Pin Relative to GND Supply Voltage Output Current Power Dissipation Commercial Operation Temperature Extended Temperature Industrial Temperature Storage Temperature 3.3V 3.3V Rating –0.5 to +4.6 –0.5 to +4.6 50 1 0 to +70 –30 to +85 –40 to +85 –55 to +125 Unit V V mA W °C °C °C °C ISSI ® TSTG Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND.) Symbol VDD VIH VIL TA Parameter Supply Voltage Input High Voltage Input Low Voltage Commercial Ambient Temperature Extended Ambient Temperature Industrial Ambient Temperature 3.3V 3.3V 3.3V Min. 3.0 2.0 –0.3 0 –30 –40 Typ. 3.3 — — — — — Max. 3.6 VDD + 0.3 0.8 +70 +85 +85 Unit V V V °C °C °C CAPACITANCE(1,2) Symbol CIN1 CIN2 CIO Parameter Input Capacitance: A0-A9 Input Capacitance: RAS, UCAS, LCAS, WE, OE Data Input/Output Capacitance: I/O0-I/O15 Max. 5 7 7 Unit pF pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 5 IS41LV16105B ELECTRICAL CHARACTERISTICS(1) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter IIL IIO VOH VOL ICC1 Input Leakage Current Output Leakage Current Output High Voltage Level Output Low Voltage Level Standby Current: TTL Test Condition Any input 0V ≤ VIN ≤ VDD Other inputs not under test = 0V Output is disabled (Hi-Z) 0V ≤ VOUT ≤ VDD IOH = –2.0 mA (3.3V) IOL = 2.0 mA (3.3V) RAS, LCAS, UCAS ≥ VIH Commerical Extended/Industrial RAS, LCAS, UCAS ≥ VDD – 0.2V RAS, LCAS, UCAS, Address Cycling, tRC = tRC (min.) RAS = VIL, LCAS, UCAS, Cycling tPC = tPC (min.) RAS Cycling, LCAS, UCAS ≥ VIH tRC = tRC (min.) RAS, LCAS, UCAS Cycling tRC = tRC (min.) 3.3V 3.3V 3.3V -50 -60 -50 -60 -50 -60 -50 -60 Speed Min. –5 –5 2.4 — — — — — — — — — — — — ISSI Max. 5 5 — 0.4 1 2 0.5 160 145 90 80 160 145 160 145 Unit µA µA V V mA mA mA mA ® ICC2 ICC3 Standby Current: CMOS Operating Current: Random Read/Write(2,3,4) Average Power Supply Current Operating Current: Fast Page Mode(2,3,4) Average Power Supply Current Refresh Current: RAS-Only(2,3) Average Power Supply Current Refresh Current: CBR(2,3,5) Average Power Supply Current ICC4 mA ICC5 mA ICC6 mA Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each Fast page cycle. 5. Enables on-chip refresh and address counters. 6 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 Min. Max. 84 — — — 50 30 8 9 38 (10, 20) ISSI -60 Min. Max. 104 — — — 60 40 10 9 40 14 0 10 0 10 40 12 30 5 10 37 0 5 3 — 20 5 10 5 0 0 0 10 — 60 15 30 10K — 10K — — 45 — — — — — 30 — — — — — — 15 15 — — — — — — — — Units ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ® Symbol t RC t RAC t CAC tAA tRAS t RP tCAS t CP t CSH t RCD tASR t RAH tASC t CAH t AR t RAD t RAL t RPC t RSH t RHCP tCLZ t CRP tOD tOE tOED tOEHC tOEP tOES t RCS t RRH t RCH t WCH Parameter Random READ or WRITE Cycle Time Access Time from RAS (6, 7) — 50 13 25 10K — 10K — — 37 — — — — — 25 — — — — — — 15 13 — — — — — — — — Access Time from CAS(6, 8, 15) Access Time from Column-Address(6) RAS Pulse Width RAS Precharge Time CAS Pulse Width(26) CAS Precharge Time(9, 25) CAS Hold Time (21) RAS to CAS Delay Time Row-Address Hold Time 12 0 8 Row-Address Setup Time Column-Address Setup Time Column-Address Hold Time Column-Address Hold Time (referenced to RAS) RAS to Column-Address Delay Time(11) Column-Address to RAS Lead Time RAS to CAS Precharge Time RAS Hold Time(27) RAS Hold Time from CAS Precharge CAS to Output in Low-Z (15, 29) (21) (20) 0 8 30 10 25 5 8 37 0 5 3 — 20 5 10 5 0 0 0 8 (20) CAS to RAS Precharge Time Output Disable Time(19, 28, 29) Output Enable Time(15, 16) Output Enable Data Delay (Write) OE HIGH Hold Time from CAS HIGH OE HIGH Pulse Width OE LOW to CAS HIGH Setup Time Read Command Setup Time Read Command Hold Time (referenced to RAS)(12) Read Command Hold Time (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) (17, 20) Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 7 IS41LV16105B AC CHARACTERISTICS (Continued)(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) Symbol t WCR tWP tWPZ t RWL t CWL tWCS t DHR t ACH tOEH t DS t DH t RWC t RWD t CWD tAWD t PC t RASP t CPA t PRWC t COH tOFF tWHZ t CLCH t CSR t CHR t ORD tREF tT Parameter Write Command Hold Time (referenced to RAS)(17) Write Command Pulse Width(17) WE Pulse Widths to Disable Outputs Write Command to RAS Lead Time Write Command Setup Time (17) (17, 21) ISSI Min. 40 8 10 13 8 0 39 15 8 0 8 108 64 26 39 20 50 (15) ® -50 Max. — — — — — — — — — — — — — — — — 100K 30 — — 12 10 — — — — 16 50 Min. 50 10 10 15 10 0 39 15 10 0 10 133 77 32 47 25 60 — 68 5 1.6 3 10 5 10 0 — 1 -60 Max. — — — — — — — — — — — — — — — — 100K 35 — — 15 10 — — — — 16 50 Units ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ms ns Write Command to CAS Lead Time (14, 17, 20) Data-in Hold Time (referenced to RAS) Column-Address Setup Time to CAS Precharge during WRITE Cycle OE Hold Time from WE during READ-MODIFY-WRITE cycle(18) Data-In Setup Time(15, 22) Data-In Hold Time(15, 22) READ-MODIFY-WRITE Cycle Time RAS to WE Delay Time during READ-MODIFY-WRITE Cycle(14) CAS to WE Delay Time(14, 20) Column-Address to WE Delay Time(14) Fast Page Mode READ or WRITE Cycle Time(24) RAS Pulse Width Access Time from CAS Precharge READ-WRITE Cycle Time(24) Data Output Hold after CAS LOW Output Buffer Turn-Off Delay from CAS or RAS(13,15,19, 29) Output Disable Delay from WE Last CAS going LOW to First CAS returning HIGH(23) CAS Setup Time (CBR REFRESH)(30, 20) CAS Hold Time (CBR REFRESH) (30, 21) — 56 5 1.6 3 10 5 8 0 — 1 OE Setup Time prior to RAS during HIDDEN REFRESH Cycle Auto Refresh Period (1,024 Cycles) Transition Time (Rise or Fall) (2, 3) 8 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B AC TEST CONDITIONS Output load: One TTL Load and 50 pF (VDD = 3.3V ±10%) Input timing reference levels: VIH = 2.0V, VIL = 0.8V (VDD = 3.3V ±10%) Output timing reference levels: VOH = 2.0V, VOL = 0.8V (3.3V ±10%) ISSI ® Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between VIH and VIL (or between VIL and VIH) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 4. If CAS and RAS = VIH, data output is High-Z. 5. If CAS = VIL, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that tRCD ≤ tRCD (MAX). If tRCD is greater than the maximum recommended value shown in this table, tRAC will increase by the amount that tRCD exceeds the value shown. 8. Assumes that tRCD ≥ tRCD (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tCP. 10. Operation with the tRCD (MAX) limit ensures that tRAC (MAX) can be met. tRCD (MAX) is specified as a reference point only; if tRCD is greater than the specified tRCD (MAX) limit, access time is controlled exclusively by tCAC. 11. Operation within the tRAD (MAX) limit ensures that tRCD (MAX) can be met. tRAD (MAX) is specified as a reference point only; if tRAD is greater than the specified tRAD (MAX) limit, access time is controlled exclusively by tAA. 12. Either tRCH or tRRH must be satisfied for a READ cycle. 13. tOFF (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to VOH or VOL. 14. tWCS, tRWD, tAWD and tCWD are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If tWCS ≥ tWCS (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If tRWD ≥ tRWD (MIN), tAWD ≥ tAWD (MIN) and tCWD ≥ tCWD (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to VIH) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after tOEH is met. 19. The I/Os are in open during READ cycles once tOD or tOFF occur. 20. The first χCAS edge to transition LOW. 21. The last χCAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling χCAS edge to first rising χCAS edge. 24. Last rising χCAS edge to next cycle’s last rising χCAS edge. 25. Last rising χCAS edge to first falling χCAS edge. 26. Each χCAS must meet minimum pulse width. 27. Last χCAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 9 IS41LV16105B FAST-PAGE-MODE READ CYCLE ISSI tRC tRAS tRP ® RAS tCSH tCRP tRCD tRSH tCAS tCLCH tRRH UCAS/LCAS tAR tRAD tASR tRAH tASC tRAL tCAH ADDRESS WE Row tRCS Column tRCH Row tAA tRAC tCAC tCLC tOFF(1) I/O Open tOE Valid Data tOD Open OE tOES Don’t Care Note: 1. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 10 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B FAST PAGE MODE READ-MODIFY-WRITE CYCLE ISSI tRASP tRP ® RAS tCSH tCAS tCRP tRCD tCP tPRWC tCAS tCP tRSH tCAS tCRP UCAS/LCAS tAR tRAH tASR tRAD tASC tCAH tCPWD tASC tAR tCWL tRWD tAWD tCWD tCAH tCPWD tRAL tCAH tASC ADDRESS Row Column Column tCWL tAWD tCWD Column tCWL tRWL tWP tAWD tCWD tRCS tWP tWP WE tAA tCAC tCAC tOEA tOEA tAA tCAC tOEA tAA OE tRAC tCLZ tOEZ tOED tDH tDS tCLZ OUT IN OUT tOEZ tOED tDH tDS IN tOEZ tOED tDH tCLZ OUT IN tDS I/O0-I/O15 Don’t Care Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 11 IS41LV16105B FAST-PAGE-MODE EARLY WRITE CYCLE (OE = DON'T CARE) ISSI tRC tRAS tRP ® RAS tCSH tCRP tRCD tRSH tCAS tCLCH UCAS/LCAS tAR tRAD tASR tRAH tASC tRAL tCAH tACH ADDRESS Row Column tCWL tRWL tWCR tWCS tWCH tWP Row WE tDHR tDS tDH I/O Valid Data Don’t Care 12 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B ISSI tRWC tRAS tRP ® FAST-PAGE-MODE READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) RAS tCSH tCRP tRCD tRSH tCAS tCLCH UCAS/LCAS tAR tRAD tASR tRAH tASC tCAH tACH tRAL ADDRESS Row tRCS Column tRWD tCWD tAWD Row tCWL tRWL tWP WE tAA tRAC tCAC tCLZ tDS tDH I/O Open tOE Valid DOUT tOD Valid DIN Open tOEH OE Don’t Care Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 13 IS41LV16105B FAST PAGE MODE EARLY WRITE CYCLE tRASP ISSI tRP tRHCP tRSH tCAS tCP tCRP ® RAS tCSH tCAS tCRP tRCD tCP tPC tCAS UCAS/LCAS tAR tRAL tRAH tASR tRAD tASC tCAH tASC tAR tCWL tWCS tWP tWCH tWCS tWP tCAH tASC tCAH ADDRESS Row Column Column tCWL tWCH tWCS Column tCWL tWCH tWP WE tWCR OE tDHR tDS tDH tDS tDH tDS tDH I/O0-I/O15 Valid DIN Valid DIN Valid DIN Don’t Care 14 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B AC WAVEFORMS READ CYCLE (With WE-Controlled Disable) RAS tCSH tCRP tRCD tCAS tCP ISSI ® UCAS/LCAS tAR tRAD tASR tRAH tASC tCAH tASC ADDRESS WE Row tRCS Column tRCH tRCS Column tAA tRAC tCAC tCLZ tWHZ tCLZ I/O Open tOE Valid Data Open tOD OE Don’t Care RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) tRC tRAS tRP RAS tCRP tRPC UCAS/LCAS tASR tRAH ADDRESS I/O Row Open Row Don’t Care Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 15 IS41LV16105B CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) ISSI tRP tRAS tRP tRAS ® RAS tRPC tCP tCHR tCSR tRPC tCSR tCHR UCAS/LCAS I/O Open HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) tRAS tRP tRAS RAS tCRP tRCD tRSH tCHR UCAS/LCAS tAR tASR tRAD tRAH tASC tRAL tCAH ADDRESS Row Column tAA tRAC tCAC tCLZ tOFF(2) I/O Open tOE tORD Valid Data Open tOD OE Don’t Care Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 16 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 IS41LV16105B ISSI Package 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free ® ORDERING INFORMATION : 3.3V Commercial Range: 0oC to +70oC Speed (ns) 50 Order Part No. IS41LV16105B-50K IS41LV16105B-50KL IS41LV16105B-50T IS41LV16105B-50TL IS41LV16105B-60K IS41LV16105B-60KL IS41LV16105B-60T IS41LV16105B-60TL 60 Extended Range: -30oC to +85oC Speed (ns) 50 Order Part No. IS41LV16105B-50KE IS41LV16105B-50KLE IS41LV16105B-50TE IS41LV16105B-50TLE IS41LV16105B-60KE IS41LV16105B-60KLE IS41LV16105B-60TE IS41LV16105B-60TLE Package 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 60 Industrial Range: -40oC to +85oC Speed (ns) 50 Order Part No. IS41LV16105B-50KI IS41LV16105B-50KLI IS41LV16105B-50TI IS41LV16105B-50TLI IS41LV16105B-60KI IS41LV16105B-60KLI IS41LV16105B-60TI IS41LV16105B-60TLI Package 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free 60 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 04/18/05 17 PACKAGING INFORMATION 400-mil Plastic SOJ Package Code: K ISSI Notes: 1. Controlling dimension: millimeters. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Reference document: JEDEC MS-027. ® N N/2+1 E1 E 1 N/2 D A SEATING PLANE b C A2 e B A1 E2 Symbol No. Leads A A1 A2 B b C D E E1 E2 e Millimeters Inches Min Max Min Max (N) 28 3.25 3.75 0.128 0.148 0.64 — 0.025 — 2.08 — 0.082 — 0.38 0.51 0.015 0.020 0.66 0.81 0.026 0.032 0.18 0.33 0.007 0.013 18.29 18.54 0.720 0.730 11.05 11.30 0.435 0.445 10.03 10.29 0.395 0.405 9.40 BSC 0.370 BSC 1.27 BSC 0.050 BSC Millimeters Min Max 32 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 20.82 21.08 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.820 0.830 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Millimeters Min Max 36 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 23.37 23.62 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 0.920 0.930 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 PACKAGING INFORMATION ISSI Millimeters Min Max 42 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 27.18 27.43 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC Inches Min Max 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.070 1.080 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Millimeters Min Max 44 3.25 3.75 0.64 — 2.08 — 0.38 0.51 0.66 0.81 0.18 0.33 28.45 28.70 11.05 11.30 10.03 10.29 9.40 BSC 1.27 BSC 0.128 0.148 0.025 — 0.082 — 0.015 0.020 0.026 0.032 0.007 0.013 1.120 1.130 0.435 0.445 0.395 0.405 0.370 BSC 0.050 BSC Inches Min Max ® Millimeters Inches Symbol Min Max Min Max No. Leads (N) 40 A 3.25 3.75 0.128 0.148 A1 0.64 — 0.025 — A2 2.08 — 0.082 — B 0.38 0.51 0.015 0.020 b 0.66 0.81 0.026 0.032 C 0.18 0.33 0.007 0.013 D 25.91 26.16 1.020 1.030 E 11.05 11.30 0.435 0.445 E1 10.03 10.29 0.395 0.405 E2 9.40 BSC 0.370 BSC e 1.27 BSC 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 10/29/03 PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) ISSI Notes: 1. Controlling dimension: millimieters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. ® N N/2+1 E1 E 1 D N/2 SEATING PLANE ZD A . e b L A1 α C Symbol Ref. Std. No. Leads A A1 b C D E1 E e L ZD α Millimeters Min Max Inches Min Max Plastic TSOP (T - Type II) Millimeters Inches Min Max Min Max 44 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.45 0.012 0.018 0.12 0.21 0.005 0.008 18.31 18.52 0.721 0.729 10.03 10.29 0.395 0.405 11.56 11.96 0.455 0.471 0.80 BSC 0.032 BSC 0.41 0.60 0.016 0.024 0.81 REF 0.032 REF 0° 5° 0° 5° Millimeters Min Max 50 — 1.20 0.05 0.15 0.30 0.45 0.12 0.21 20.82 21.08 10.03 10.29 11.56 11.96 0.80 BSC 0.40 0.60 0.88 REF 0° 5° Inches Min Max (N) 32 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.52 0.012 0.020 0.12 0.21 0.005 0.008 20.82 21.08 0.820 0.830 10.03 10.29 0.391 0.400 11.56 11.96 0.451 0.466 1.27 BSC 0.050 BSC 0.40 0.60 0.016 0.024 0.95 REF 0.037 REF 0° 5° 0° 5° — 0.047 0.002 0.006 0.012 0.018 0.005 0.008 0.820 0.830 0.395 0.405 0.455 0.471 0.031 BSC 0.016 0.024 0.035 REF 0° 5° Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 06/18/03