IS61C3216-15KI

OS-CON DATA SHEET OS-CON 6SVP470M Frequency (kHz) Impedance (ohm) ESR (ohm) 0.12 2.824 0.084 0.5 0.691 0.044 1 0.353 0.037 10 0.046 0.017 100 0.010 0.009 500 0.013 0.009 1000 0.024 0.009 5000 0.103 0.022 10000 0.230 0.024 No.OS02N-DFSVP051 Frequency characteristics 1000 100 Impedance (ohm) ESR (ohm) ESR, Impedance (ohm) 10 1 0.1 0.01 0.001 0.1 1 10 100 1000 10000 Frequency (kHz) Measureing equipment: HP4194A Test fixture: HP16047C Measuring position: root of leads OS Engineering Department, OS-CON Control Department Saga SANYO Industries Co., Ltd. n = 3p.(Ave.) Room temperature OS-CON DATA SHEET SVP series Test item Endurance (After V.P.S test) Test temperature 105 deg.C Applied voltage 6.3V Model 6SVP470M Lot No. 130106406 Change in capacitance (120Hz) 20 10 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 Tangent of loss angle (120Hz) 0 -10 -20 -30 -40 0 2000 Tangent of loss angle Percent delta [%] 0 2000 Time[h] Time[h] ESR (100kHz) 100 90 80 70 60 50 40 30 20 10 0 10000 Leakage current (6.3V 60s) Leakage current(µA) 1000 100 10 1 0.1 0.01 ESR(mohm) 0 2000 0 2000 Time[h] Time[h] Note: n =30p. V.P.S test conditions : 230deg.C×75s×2times (V.P.S=Vapor Phase Soldering method) Start on September 10, 2001 Executed by R. Kawachino End on December 2, 2001 Drawn by S. Yoshino No.OS02D-DESVP051 OS Engineering Departmaent, OS-CON Control Department, Saga SANYO Industries Co., Ltd. OS-CON DATA SHEET SVP series Test item Damp heat (Steady state) (After V.P.S test) Test temperature 60 deg.C Test humidity 90% RH Model 6SVP470M Lot No. 060202471 Change in capacitance (120Hz) 20 10 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 Tangent of loss angle (120Hz) Tangent of loss angle Percent delta [%] 0 -10 -20 -30 -40 0 1000 0 1000 Time[h] Time[h] ESR (100kHz) 100 90 80 70 60 50 40 30 20 10 0 10000 Leakage current (6.3V 60s) Leakage current(µA) 0 1000 1000 100 10 1 0.1 0.01 ESR(mohm) 0 1000 Time[h] Time[h] Note: n =20p. V.P.S test conditions : 230deg.C×75s×2times (V.P.S = Vapor Phase Soldering method) Start on November 7, 2001 Executed by R. Kawachino End on December 20, 2001 Drawn by M. Kimura No.OS02D-DHSVP051 OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.