F2201

SAW Bandpass Filter F2201 Features RF bandpass filter High attenuation Usable bandwidth 1MHz No matching 50Ω single-ended operation Ceramic Surface Mounted Device (SMD) Package 2.08±0.15 Package Dimensions 5.00±0.15 8 1.2±0.15 8 5.00±0.15 1 2 3 7 7 6 5 1 2 3 ITF 2201 4 6 5 1.35±0.15 1.27±0.05 4 Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating Pin Configuration 2 6 1, 3, 4, 5, 7, 8 Input Output Case ground Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Power Handling Capability Electrostatics Sensitive Device (ESD) Unit °C °C dBm Minimum -30 -40 Typical 25 Maximum 85 85 - I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. 0.6±0.15 F2201 2008.10.07. NR6001-AS03 1/7 SAW Bandpass Filter F2201 Specifications Fc = 220.0MHz Terminating source impedance Terminating load impedance : 50Ω and matching network : 50Ω and matching network Minimum Center Frequency ( Fc ) Insertion Loss (Fc +/- 0.5 MHz) Amplitude Ripple (Fc +/- 0.5 MHz) Absolute Group Delay at Fc Group Delay Variation (Fc +/- 0.5 MHz) VSWR (Fc +/- 0.5 MHz) Relative Attenuation … ~ Fc - 10 MHz Fc + 20 MHz ~ … Temperature Coefficient of Frequency MHz dB dB nsec nsec - Typical 220.0 2.5 1.0 250 250 1.5 Maximum 3.5 1.5 - dB 40 40 - 45 45 -32 - ppm/°C - Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 2/7 SAW Bandpass Filter F2201 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration ITF1) 22012) 1) Manufacturer name 2) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 3/7 SAW Bandpass Filter F2201 Frequency Response I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 4/7 SAW Bandpass Filter F2201 Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 5/7 SAW Bandpass Filter F2201 Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Top cover tape Direction of pull 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g Carrier tape I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 6/7 SAW Bandpass Filter F2201 Carrier Tape Dimensions [unit : mm] A B C D E F 5.50 ± 0.1 5.50 ± 0.1 7.25 ± 0.1 1.95 ± 0.1 12.00 ± 0.1 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2201 2008.10.07. NR6001-AS03 7/7