F2202

SAW Bandpass Filter F2202 Features RF bandpass filter Usable bandwidth 0.6MHz No matching single-ended operation Ceramic Surface Mounted Device Package ( 5.0 mm × 5.0 mm ) Package Dimensions 2.08±0.15 0.6±0.15 1 2 3 5.00±0.15 8 1.2±0.15 8 5.00±0.15 1 2 3 7 7 6 5 ITF 2202 4 6 5 1.35±0.15 1.27±0.05 4 Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating Pin Configurations 2 6 1, 3, 4, 5, 7, 8 Input Output Ground Maximum Ratings Parameters Operating Temperature Range Storage Temperature Range Power Handling Capability Electrostatics Sensitive Device (ESD) Unit °C °C dBm Minimum -30 -40 Typical 25 Maximum 85 85 10 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 1/7 SAW Bandpass Filter F2202 Preliminary Specifications Minimum Center Frequency ( Fc ) Insertion Loss Pass Bandwidth Amplitude Ripple (Fc ± 0.3MHz) VSWR (Fc ± 0.3MHz) 0.6 Typical 220.0 2.5 2.0 0.5 1.5 1.5 2.0 Maximum 3.5 Unit MHz dB MHz dB Attenuation ~ Fc -10.7MHz Fc + 10.7MHz ~ 37 25 - - dB Temperature Range (Operational) Input/Output Impedance -30 25 50 85 ℃ Ohms Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 2/7 SAW Bandpass Filter F2202 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration ITF 1) 2202 2) 1) Manufacturer name 2) Marking Number I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 3/7 SAW Bandpass Filter F2202 Frequency Response I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 4/7 SAW Bandpass Filter F2202 Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 5/7 SAW Bandpass Filter F2202 Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Top cover tape Direction of pull 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g Carrier tape I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 6/7 SAW Bandpass Filter F2202 Carrier Tape Dimensions [unit : mm] A B C D E F 5.50 ± 0.1 5.50 ± 0.1 7.25 ± 0.1 1.95 ± 0.1 12.00 ± 0.1 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] G = 2G = 12.40 mm I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2202 2008/07/11 NR8001-AS03 7/7