F2G16

SAW Bandpass Filter F2G16 Features RF bandpass filter for GSM Usable Bandwidth 45MHz No matching single-ended operation Ceramic Surface Mounted Device Package ( 3.0 mm × 3.0 mm ) RoHS Compliant Package Dimension 1 6 6 1 2 I 2G16 5 5 2 3 4 4 3 Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating Pin Configurations 2 5 1, 3, 4, 6 Input Output Case ground Maximum Ratings Parameters Operating Temperature Range Storage Temperature Range Power Handling Capability Electrostatics Sensitive Device (ESD) Unit ℃ ℃ dBm Minimum -30 -40 Typical 25 Maximum 85 95 13 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 1/7 SAW Bandpass Filter F2G16 Specifications Fo = 2132.5 MHz Minimum Center Frequency ( Fc ) Insertion Loss (In Fc ± 22.5 MHz) Amplitude Ripple (In Fc ± 22.5 MHz) VSWR (In Fc ± 22.5 MHz) - Typical 2132.5 2.5 1.0 1.6 Maximum 3.7 2.0 2.5 Unit MHz dB dB Relative Attenuation dB 1800.0MHz ~ 2070.0MHz 2195.0MHz ~ 2400.0MHz 25 25 34 40 - Input/Output Impedance 50 Ohm Notes : 1) 2) 3) All specifications are based on the matching schematic shown below All specifications are measured by Agilent Network analyzer and full 2 port calibration at room temperature All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 2/7 SAW Bandpass Filter F2G16 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration 1) I2) 2G163) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 3/7 SAW Bandpass Filter F2G16 Typical Performance ( at +25℃ ) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 4/7 SAW Bandpass Filter F2G16 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 5/7 SAW Bandpass Filter F2G16 Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Top cover tape Direction of pull 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g Carrier tape I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 6/7 SAW Bandpass Filter F2G16 Carrier Tape Dimensions [unit : mm] A B C D E F 3.40 ± 0.1 3.40 ± 0.1 7.25 ± 0.1 1.70 ± 0.1 12.00 ± 0.1 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F2G16 2009-08-17 NC9010-AS01 7/7