F9533

SAW Bandpass Filter F9533 Features RF bandpass filter for RF-ID System Usable bandwidth 2 MHz (952.0 MHz ~ 954.0 MHz) single-ended operation Ceramic Surface Mounted Device Package ( 3.8 mm × 3.8 mm ) RoHS Compliant Package Dimensions 3.80±0.15 1.00±0.15 0.44 1.90±0.15 0.64±0.05 1 0.44 5 5 2 3 1.27±0.05 1 6 6 2 ITF 9533 8H1 3.80±0.15 Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 1.40±0.15 3 4 4 Pin Configurations 2 5 1, 3, 4, 6 Input Output Case ground Maximum Ratings Parameters Operating Temperature Range Storage Temperature Range Power Handling Capability Electrostatics Sensitive Device (ESD) Unit °C °C dBm Minimum -30 -40 Typical 25 Maximum 85 85 20 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 1/7 SAW Bandpass Filter F9533 Specifications Minimum Center Frequency ( Fc ) Insertion Loss (In Fc ±1.0 MHz) Amplitude Ripple (In Fc ±1.0 MHz) VSWR (In Fc ±1.0 MHz) Typical 953.0 4.5 1.0 2.0 Maximum 5.5 2.0 3.0 Unit MHz dB dB Relative Attenuation 830.0 MHz ~ 940.0 MHz ~ 945.0 MHz ~ 948.0 MHz ~ 956.0 MHz ~ 840.0 MHz 945.0 MHz 948.0 MHz 950.0 MHz 958.0 MHz 30 20 15 12 25 35 25 20 16 30 dB Input/Output Impedance 50 Ohm Notes : 1) All specifications are based on the matching schematic shown below, measured by Agilent Network analyzer and full 2 port calibration. 2) Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances 3) All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 2/7 SAW Bandpass Filter F9533 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω L2 L3 Output 50Ω L1 L4 L1 = 3.9nH, L2 = L3 =4.7nH, L4 = 3.3nH Marking Configuration 1) ITF2) 95333) 8H14) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number 4) Lot Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 3/7 SAW Bandpass Filter F9533 Typical Performance ( at 25℃ ) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 4/7 SAW Bandpass Filter F9533 Input / Output VSWR Charts Input / Output Smith Charts I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 5/7 SAW Bandpass Filter F9533 Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Top cover tape Direction of pull 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g Carrier tape I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 6/7 SAW Bandpass Filter F9533 Carrier Tape Dimensions [unit : mm] A B C D E F 3.40 ± 0.1 3.40 ± 0.1 7.25 ± 0.1 1.70 ± 0.1 12.00 ± 0.1 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. F9533 2008-08-07 NR8006-AS01 7/7