R39501

SAW Resonator R39501 Features 1-port Resonator Quartz Frequency Stabilization For transmitters or Local Oscillators Package Dimension – S5050 2.08±0.15 0.6±0.15 1 2 3 5.00±0.15 8 1.2±0.15 8 5.00±0.15 1 2 3 7 6 5 7 6 5 1.35±0.15 1.27±0.05 4 4 Pin Configuration 2 6 1, 3, 4, 5, 7, 8 Input Output Ground Package Dimension – TO-39 Pin Configuration 1 2 3 Input Output Case ground I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 1/6 SAW Resonator R39501 Package Dimension – F-11 Pin Configuration 1 4 2, 3 Input Output Case ground Marking Configuration ITF1) 395012) 1) Manufacturer name 2) Marking Number * Ink or Laser Marking available * Front 4 digits for S5050 Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Power Handling Capability Electrostatics Sensitive Device (ESD) Unit °C °C dBm Minimum -10 -40 Typical 25 0 Maximum 60 85 - I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 2/6 SAW Resonator R39501 Electrical Specification FR = 395.0MHz Terminating source impedance Terminating load impedance : 50Ω and matching network : 50Ω and matching network Minimum Resonance Frequency ( FR ) Insertion Loss 50 ohm Loaded Q Unloaded Q Trun-over Temperature Temperature Coefficient of Frequency °C ppm/°C2 10 MHz dB 394.925 - Typical 395.000 1.5 2,000 12,800 25 -0.032 Maximum 395.075 2.5 40 - Notes : 1) 2) All specifications are based on the matching schematic shown below All specifications are measured by Agilent Network analyzer and full 2 port calibration at room temperature Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 3/6 SAW Resonator R39501 Frequency Response 0 -5 Insertion Loss ( dB ) -10 -15 -20 -25 -30 Frequency I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 4/6 SAW Resonator R39501 Packing Specification 1. Reeling Quantity : 1000 pcs / reel 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Top cover tape Direction of pull 3. Top cover tape adhesion 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g Carrier tape 0~15 degree I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 5/6 SAW Resonator R39501 Carrier Tape Dimensions [unit : mm] A B C D E F 5.50 ± 0.1 5.50 ± 0.1 7.25 ± 0.1 1.95 ± 0.1 12.00 ± 0.1 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. Rev. Date Rev. R39501 2004-04-20 NS3116-AS01 6/6