INTERMATEABLE WITH SOURIAU CONNECTORS
ITT Cannon Trident connectors are a family of cost-effective, reliable circular connectors
that include the Trident Ringlock, Trident Neptune and TNM series. All three series
of ITT Cannon Trident connectors are fully-sealed to IP67. The Trident Ringlock and
Trident Neptune series are UL94-V0 circular plastic connectors with a metal coupling
nut and bayonet retention mechanisms, providing the cost and weight benefits of a
plastic connector with the durability of a metal connector. Trident Ringlock connectors
are intermateable with SOURIAU/Burndy Trim-Trio (UTG). Trident Neptune uses
the same contacts as Ringlock, but is a unique product perfect as a transportation
connector or in harsh environments where full-sealing and a mix of power and signal
contacts are required. ITT Cannon’s TNM series is an all-metal version similar to
MIL-DTL-26482, but lower cost and not intermateable. For full details on the ITT
Cannon Trident connector family, see the product specifications below.
APPLICATIONS
Industrial and vehicular connections to and from electronic cabinets and boxes. Any power and signal
application requiring total moisture sealing.
• Trucks & buses
• Industrial machinery
• Off-road vehicles
• Control cables
• Rail and mass transit
• Probes
• Marine
• Hand controllers
• Process control
• Remote sensors
• Inter-system connections
FEATURES
STRONG, LIGHT-WEIGHT & LOW-COST
Superior to plastic circular connectors and less
costly than metal connectors, Trident’s metal bayonet
coupling nut and locking mechanism provide
strength and life comparable to an all-metal connector.
Bodies are composed of durable UL94V0
thermoplastic with high-strength nickel-plated metal
coupling nuts and bayonet ring. Molded rubber and
silicone seals guarantee water-tightness.
ATTRACTIVE APPEARANCE
Trident connectors are aesthetically-pleasing, making
them perfect for front panel mounting.
SUBMERSIBLE OR
WATERJET-PROOF VERSIONS
Neptune uses a rear individual wire sealing grommet
and is fully submersible to IP67. Ringlock is protected
against submersion to IP67 using gland seal
cable clamp.
WIDE TEMPERATURE RANGE
Trident will operate in temperatures from -55ºC to
+120ºC (-67º to +248ºF) under conditions of high
humidity, severe vibration, ice and mud.
WIDE RANGE OF WIRE GAUGES AND
CURRENT CARRYING CAPABILITY
Up to 30 amps per contact with wire sizes from 28
AWG up to 12 AWG wire. TNM 700-volt handles up
to 40 amp power for up to 8 AWG wire.
STANDARD AND REVERSE
CONNECTOR HOUSINGS
In the STANDARD configuration, the receptacles use
socket contacts and the plugs use
pin contacts. A REVERSED version is also available
for safety and/or polarization. Standard and reversed
connectors will not intermate. ‘Keying Pins’ are
also available to polarize connectors with the same
orientation and layout used on the same panel
to prevent mis-mating.
WIDE RANGE OF CONTACT STYLES
Contacts are available in crimp, PC, coax, wire wrap
or first mate/last break for ground connections.
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
ITT Cannon Trident Connectors:
Trident Ringlock, Trident Neptune & TNM
FIELD SERVICEABLE
The use of removable crimp contacts allows
connections to be changed or modified in the field
if necessary. Contacts are copper alloy with a range
of gold or tin platings.
AGENCY APPROVALS
• UL and CSA (Trident Ringlock)
• IP67 Submersible
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
39
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
TECH SPECS
MATERIALS & FINISHES
Shell
Plating
UL94V0 thermoplastic with nickel-plated copper alloy coupling nut
and bayonet lock ring
High-reliability copper alloy available in two versions: stamped and
formed or machined
Tin, gold flash, gold (1 micron), heavy gold (4 microns)
Seals
Rubber, silicone
Contacts
ELECTRICAL DATA
Operating Voltage
Contact Resistance
Up to 250 Vac rms degree of pollution permitting per IEC664
(TNM 700-volt power version)
2000 Vac rms test potential
30 Amps (Neptune Power contacts), 13 Amps (Signal contacts).
16 Amp contacts available. TNM 40 amp power.
28 - 14 AWG (stamped contacts), 28 - 16 AWG (machined),
18 - 12 AWG (Power Neptune) 16 - 8 AWG (Power TNM)
5 Milliohms Initial
Insulation Resistance
5000 Megaohms at 500Vdc
Crimp Contacts
Semi-automatic, hand-crimpable or fully-automatic
Wire Size
20 - 16 AWG
Wire Insulation Sealing Range
1.98 mm (.078 in) to 3.30 mm (.130 in) diameter
Contact Insertion
No tool required. Suitable for automation.
Contact Extraction
Rear removable
Contact Retention
20 lbs. minimum per contact
Wire Strip Length
5.59 mm (.220 in) to 5.33 mm (.210 in)
Test Voltage
Current rating
Wire Range Sizes
MECHANICAL DATA
Sealing
Up to IP67
Wire Sealing Range
Insulation Strip Lengths
Mating Life
See column 9 on contact chart, a page 49.
See column 8 on contact chart, a page 49.
500 cycles (machined contacts); 200 cycles (stamped)
Salt Spray
To MIL-STD-1344 Method 1001 (48 hrs. no corrosion)
Heat
Vibration
Damp Heat to BS 2011 Pt2 Ca, 21 days exposure +105°C to -50°C
(5 cycles) remains within specifications
Connectors show no damage when exposed to fluids used in industrial/
vehicle applications.
5 to 55 Hz (1 minute) No discontinuities longer than 1-microsecond
Shock
50g 11ms MIL-STD-202 Method 213 condition A
Contact Type
Crimp, PC, first mate/last break, co-ax, wire wrap
Number of Circuits
4 to 48
Contact Insertion
From rear. No insertion tool needed. Removable with proper extraction
tool (front release).
Chemical Resistance
CONTACT
40
FORCE (MIN)
LBS.
NEWTONS
Machined
25
110
Stamped
15
65
Polarization
Standard or reversed sex shells and/or keying pins
Agency Listing
UL (E102053), CSA (LR68300), TNM: UL, C-UL, E151413
Color
Silver (TNM) or Black with silver coupling nut and ring
(Ringlock and Neptune)
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
NEPTUNE
PLUG
FLANGED
RECEPTACLE
FLANGED
PLUG
RECEPTACLE
INTERNAL
O-RING
(NOT VISIBLE)
INDIVIDUAL
WIRE SEALING
GROMMET
STANDARD
ENDBELL
(INCLUDED)
SHELL
JAM NUT
RECEPTACLE
JAM NUT
SHELL
METAL
BAYONET LOCK
METAL
COUPLING
NUT
JAM NUT
RECEPTACLE
INTERNAL
O-RING
(NOT VISIBLE)
STANDARD
ENDBELL
(INCLUDED)
INDIVIDUAL
WIRE SEALING
GROMMET
SHELL
METAL
BAYONET LOCK
STANDARD
ENDBELL
(INCLUDED)
INDIVIDUAL
WIRE SEALING
GROMMET
RINGLOCK
FLANGED
FLANGED
FLANGED
RECEPTACLE
RECEPTACLE
RECEPTACLE
PLUG
PLUG PLUG
ENDBELL ENDBELL
INTERNALINTERNAL
(VARIOUS(VARIOUS
OPTIONALOPTIONAL
O-RING O-RING
(NOT
VISIBLE)
STYLES) STYLES)
(NOT VISIBLE)
ENDBELL ENDBELL
(VARIOUS(VARIOUS
OPTIONALOPTIONAL
STYLES) STYLES)
SHELL
SHELL
METAL METAL
COUPLING
NUT
COUPLING
NUT
SHELL
SHELL
METAL METAL
LOCK
BAYONETBAYONET
LOCK
TNM
PLUG
PLUG
PLUG
FLANGED
FLANGED
RECEPTACLE
RECEPTACLE
FLANGED
RECEPTACLE
NICKEL
STANDARD
NICKEL PLATED
STANDARDENDBELL
INTERNAL
CONDUCTIVE
PLATED
(INCLUDED WITH
ENDBELL
INTERNAL O-RING
CAST ZINC
(NOTCONDUCTIVE
VISIBLE)
SEALED
(INCLUDED
WITH VERSION)
O-RING
CAST ZINC SHELL
(NOT VISIBLE)
SEALED
VERSION)
SHELL
INDIVIDUAL
WIRE SEALING
INDIVIDUAL
GROMMET
WIRE SEALING
(INCLUDED WITH
GROMMET
SEALED
(INCLUDED
WITHVERSION)
SEALED VERSION)
STANDARD
NICKEL
METAL
ENDBELL
STANDARD
NICKEL PLATED
(INCLUDED
METAL COUPLING
ENDBELL
CONDUCTIVE
PLATED
NUT
(INCLUDED WITH
CASTCOUPLING
ZINC
CONDUCTIVE
NUT
WITH SEALED
CAST ZINC SHELL
SHELL
SEALED VERSION)
VERSION)
LIGHT ROPE
INDIVIDUAL
METAL
WIRE SEALING
INDIVIDUAL
BAYONET LOCK
GROMMET
METAL
WIRE SEALING
BAYONET LOCK
(INCLUDED WITH
GROMMET
SEALED
(INCLUDED WITH VERSION)
SEALED VERSION)
HIGH POWER
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
EXPLODED VIEW
700 VOLT HIGH POWER
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
41
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
SELECT PAR T NUMBER - STANDARD SEX
INDEX
CONNECTORS
Plug (Pins)
Neptune
(Shaded)
Jam Nut
Receptacle
(Sockets)
(Neptune version pictured)
Mates With
192991-0625 192991-0615
Special High Power
2 Combo-D Contacts
12 Signal Contacts
Ringlock
Flanged
Receptacle
(Sockets)
GLAND NUT
SECURING
RUBBER SEAL
# OF
CIRCUITS
# OF
POWER
CONTACTS
# OF
SIGNAL
CONTACTS
SHELL
SIZE
PLUGS (PINS)
PLUG (PINS)
PLASTIC
COUPLING NUT
FLANGED
RECEPTACLE
(SOCKETS)
JAM NUT
RECEPTACLE
(SOCKETS)
4
0
4
10
192922-1250
-
192990-1660
-
7
0
7
18
192990-1330
-
192990-1700
-
8
0
8
12
192922-1260
-
192990-1670
-
12
0
12
14
192922-1270
-
192990-1680
-
12
0
12
14
192900-0303
-
192900-0308
192900-0313
15
2
13
16
192900-0507
192900-0561
192900-0509
192900-0508
19
0
19
16
192922-1280#
-
192990-1690#
-
19
0
19
16
192900-0017
192900-0557
192900-0039
192900-0490
23
0
23
18
192990-1320
-
192990-1710
-
24
4
20
24
192900-0014
192900-0537
192900-0030
192900-0032
28
0
28
20
192922-1290
-
192990-1720
-
31
12
19
24
192900-0016
192900-0538
192900-0036
192900-0038
32
4
28
24
192900-0015
192900-0549
192900-0033
192900-0035
35
0
35
22
192922-1300
-
192990-1730
-
48
0
48
24
192990-1340
192990-0553
192990-1740
-
48
0
48
24
192900-0469
192991-0628 (L)
192900-0539
192991-0660 (L)
192900-0475
192991-0640 (L)
192900-0481
192991-0644 (L)
Mating face of plug for Standard Sex is shown. Reverse Sex has mirror image cavity identification. Shaded columns = Neptune Version - Supplied with individual wire seal.
+2 COAX / Power +12 signal. Ringlock version contact us for details.
42
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
INDEX
CONNECTORS
Plug (Pins)
Neptune
(Shaded)
Jam Nut
Receptacle
(Sockets)
(Neptune version pictured)
Mates With
192991-0625 192991-0615
Special High Power
2 Combo-D Contacts
12 Signal Contacts
Ringlock
Flanged
Receptacle
(Sockets)
GLAND NUT
SECURING
RUBBER SEAL
# OF
CIRCUITS
# OF
POWER
CONTACTS
# OF
SIGNAL
CONTACTS
SHELL
SIZE
PLUG (SOCKETS)
PLUG (SOCKETS)
PLASTIC
COUPLING NUT
FLANGED
RECEPTACLE
(PINS)
JAM NUT
RECEPTACLE
(PINS)
4
0
4
10
192926-0500
-
192990-1760
-
7
0
7
18
192990-1390
-
192990-1800
-
8
0
8
12
192926-0510
-
192990-1770
-
12
0
12
14
192926-0520
-
192990-1780
-
12
0
12
14
192900-0236
-
192900-0256
192900-0266
15
2
13
16
192900-0581
192900-0562
192900-0582
192900-0583
19
0
19
16
192926-0530#
-
192990-1790#
-
19
0
19
16
192900-0057
192900-0558
192900-0078
192900-0353
23
0
23
18
192990-1380
-
192990-1810
-
24
4
20
24
192900-0054
192900-0540
192900-0069
192900-0071
28
0
28
20
192926-0540
-
192990-1820
-
31
12
19
24
192900-0056
192900-0541
192900-0075
192900-0077
32
4
28
24
192900-0055
192900-0550
192900-0072
192900-0074
35
0
35
22
192926-0550
-
192990-1830
-
48
0
48
24
192990-1400
192900-0554
192990-1840
-
48
0
48
24
192900-0425
192991-0648 (L)
192900-0542
192991-0664 (L)
192900-0431
192991-0652 (L)
192900-0437
192991-0656 (L)
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
SELECT PAR T NUMBER - REVERSE SEX
Shaded columns = Neptune Version - Supplied with individual wire seal.
# Mates with TNM, but not with Neptune version
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
43
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
SELECT PAR T NUMBER - ACCESSORIES
** For Jam Nut
* For Flanged
SEAL
GASKETS
# OF
CIRCUITS
SHELL
SIZE
NEPTUNE WIRE
SEALING RANGE
INCHES (MM) MIN OD
MAX OD
FOR JAM NUT**
FOR FLANGED*
RINGLOCK
EXTERNALLY
GROOVED FOR HEAT
SHRINK
NEPTUNE HEAT
SHRINK BOOT OR
FLEX TUBING†
WATERPROOF
GLAND SEAL
ENDBELL •
4
10
N/A
075-8543-011
192990-1430
-
192990-1530
7
18
N/A
075-8543-015
192990-1470
-
192990-1570
8
12
N/A
075-8543-012
192990-1440
-
192990-1540
12
14
N/A
075-8543-013
192990-1450
-
192990-1550
12
14
.067 (1.7) .106 (2.7)
192900-0565*
192900-0457**
-
-
192900-0496
15
16
Signal: .067 (1.7) .106 (2.7)
Power: .106 (2.7) .157 (4.0)
192900-0566*
192900-0402**
-
192991-0015
192900-0497
19
16
N/A
075-8543-014
192990-1460
-
192990-1560
19
16
.067 (1.7) .106 (2.7)
192900-0566*
192900-0402**
-
192991-0015
192900-0497
23
18
N/A
075-8543-015
192990-1470
-
192990-1570
24
24
Signal: .067 (1.7) .106 (2.7)
Power: .106 (2.7) .157 (4.0)
192900-0567*
192900-0458**
-
192991-0013
192900-0498
28
20
N/A
075-8543-016
192990-1480
-
192990-1580
31
24
Signal: .067 (1.7) .106 (2.7)
Power: .106 (2.7) .157 (4.0)
192900-0567*
192900-0458**
-
192991-0013
192900-0498
32
24
Signal: .067 (1.7) .106 (2.7)
Power: .106 (2.7) .157 (4.0)
192900-0567*
192900-0458**
-
192991-0013
192900-0498
35
22
N/A
075-8543-017
192990-1490
-
192990-1590
48
24
N/A
075-8543-018
192990-1500
-
192990-1600
48
24
.063 (1.6) .087 (2.2)
.090 (2.3) .126 (3.2)
192900-0567
192900-0458**
192900-0498
192900-0344
192991-0581
Shaded rows = Neptune Version - Supplied with individual wire seal.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
44
ENDBELLS
• See a page 57 for cable sealing range.
† See Accessories a pages 196-201 for heat shrink boots and tubing.
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
ENDBELLS
# OF CIRCUITS SHELL SIZE
DUST CAPS (ALSO FITS KPT/KPSE SERIES)
STANDARD STRAIN
RELIEF (UNSEALED)
LOW PROFILE 90°
RECEPTACLE
METAL DUST CAP
RECEPTACLE
PLASTIC DUST CAP
PLUG PLASTIC
DUST CAP ‡
4
10
192922-1310
-
192922-1480
192900-0666
192900-0385r
7
18
192990-1510
-
192990-1410
192900-0670
192900-0389r
8
12
192922-1320
-
192922-1490
192900-0667
192900-0386r
12
14
192922-1330
-
192922-1500
192900-0668
192900-0387r
12
14
192900-0286
192991-0579
192922-1500
192900-0378
192991-0673
15
16
192900-0343
192991-0580
192922-1510
192900-0379
192900-0388
19
16
192922-1340
-
192922-1510
192900-0669
192900-0388
19
16
192900-0343
192991-0580
192922-1510
192900-0379
192900-0388
23
18
192990-1510
-
192990-1410
192900-0670
192900-0389r
24
24
192900-0344
192991-0581
192900-1420
192900-0383
192900-0392
28
20
192922-1350
-
192922-1520
192900-0671
192900-0390r
31
24
192900-0344
192991-0581
192990-1420
192900-0383
192900-0392
32
24
192900-0344
192991-0581
192990-1420
192900-0383
192900-0392
35
22
192922-1360
-
192922-1530
192900-0672
192900-0391r
48
24
192990-1520
-
192990-1420
192900-0673
192900-0392
48
24
192900-0344
192991-0581
192990-1420
192900-0383
192900-0392
Shaded rows = Neptune Version - Supplied with individual wire seal.
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
SELECT PAR T NUMBER - ACCESSORIES
‡
Plug cap can be panel mounted and used as a dummy receptacle. Contact us for instructions
r Large minimums may apply to these caps
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
45
Find Parts Fast with
Parametric Search
Shop Online
+1 800.675.1214 (North America)
+44 (0) 23 8062 1260 (Europe)
Track Your Orders
+86 756 7683 088 (Asia)
in Real-Time
+1 631.475.5050
(Rest
of World)
For assistance
in North America: +1
800.675.1214
• www.peigenesis.com • sales@peigenesis.com
Upload Your BOM
View Invoice
History & More
30
POWER
CONTACTS
25
Curves apply to single contacts in isolation. Use of smaller wire gauges
or more than one contact in a connector requires derating.
Contact us for additional derating information.
LIMIT OF SIGNAL
CONTACTS
20
Operating Current (A)
Derating Curve
Temperature rise vs. current
for maximum wire sizes
STAMPED
(TIN)
15
STAMPED
(GOLD)
10
MACHINED
5
30° C TEMPERATURE
RISE
70
90
80
100
110
120
125
Ambient Temperature (C°)
HOW TO SELECT TRIDENT CONNECTORS ( a SEE PAGES 42-45)
STEP 1.
STEP 2.
STEP 3.
Determine number of circuits required per connector (4 to 48). Note that some Neptune layouts (shaded rows) have
a mixture of power and signal contacts.
Choose Trident Ringlock (waterjet-proof) or Neptune (submersible). Neptune part numbers are shaded in chart.
Select connector sex: STANDARD or REVERSED. Standard plugs have pin contacts, receptacles have sockets.
Reversed plugs have socket contacts, receptacles have pins.
STEP 4.
Choose shell style: PLUG, FLANGED RECEPTACLE, or JAM NUT.
STEP 5.
Find part number on chart (shaded part numbers are NEPTUNE).
STEP 6.
Select endbell, if needed. Neptune comes with low profile wire seal endbell; however, all endbells shown can be
optionally used with Neptune connectors.
STEP 7.
Choose dust cap, if required.
STEP 8.
Select contacts and tooling below.
HOW TO SELECT TRIDENT CONTACTS ( a SEE PAGES 48-49)
STEP 1. Choose stamped or machined contacts.
STEP 2. Choose contact type: crimp, PC, power, first mate/last break.
STEP 3. Find your desired wire gauge in COLUMN 2.
STEP 4. Choose contact plating in COLUMN 3.
STEP 5. Select part number from COLUMNS 4, 5, 6, or 7.
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
CURRENT RATING (BY AMBIENT TEMPERATURE)
STEP 6. Select wire hole filler plugs (if needed) from COLUMN 10. Hole filler plugs are for Neptune version only (gray shaded
connectors). Hole fillers are only used to re-seal unused grommet cavities that were punched out, but will not be filled
with a wire.
STEP 7. Select Keying pins (if needed) from COLUMN 11.
STEP 8. Choose proper crimp tool for your contact from COLUMNS 12 thru 14.
STEP 9. Choose proper extraction tool from COLUMN 15 (insertion tool not needed).
STEP 10. Wire strip lengths and insulation dimensions are in COLUMNS 8 and 9.
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
47
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
CONTACTS (1)
COLUMN 1
COLUMN 2
COLUMN 3
COLUMN 4
COLUMN 5
COLUMN 6
COLUMN 7
TRIDENT CONTACTS
A.W.G. WIRE SIZE
PLATING
LOOSE PINS
3K REEL PIN
LOOSE
SOCKETS
3K REEL
SOCKETS
24-26
Tin
Gold flash
Gold
192990-0020
192990-0080
192900-0448
192990-2510
192990-2650
192900-0406
192990-0030
192990-0090
192900-0452
192990-2550
192990-2690
192900-0410
20-22
Tin
Gold flash
Gold
192990-0040
192922-1460
192900-0447
192990-2500
192990-2640
192900-0405
192990-0050
192922-1470
192900-0451
192990-2540
192990-2680
192900-0409
Contact us for high-conductivity contacts (16A)
16-18
Tin
Gold flash
Gold
192990-0060
192990-0100
192900-0446
192990-2490
192990-2630
192900-0404
192990-0070
192990-0110
192900-0450
192990-2530
192990-2670
192900-0408
Non-insulation support
14
Tin
Gold flash
Gold
192990-1240
192990-1220
192900-0445
192990-2480
192990-2620
192900-0403
192990-1250
192990-1230
192900-0449
192990-2520
192990-2660
192900-0407
24-28
Gold flash
Gold
Heavy Gold
192991-0099
192991-0100
192991-0101
-
192991-0036
192991-0042
192991-0054
-
24
Gold flash
Gold
Heavy Gold
192991-0091
192991-0092
192991-0093
-
192991-0037
192991-0043
192991-0055
-
22
Gold flash
Gold
Heavy Gold
192991-0095
192991-0096
192991-0097
-
192991-0038
192991-0044
192990-0056
-
20
Gold flash
Gold
Heavy Gold
192991-0127
192991-0128
192991-0129
-
192991-0039
192991-0045
192991-0057
-
20
20 Thick Wire
Gold flash
Gold
Heavy Gold
192991-0087
192991-0088
192991-0089
-
192991-0040
192991-0046
192991-0058
-
16-18
Gold flash
Gold
Heavy Gold
192991-0083
192991-0084
192991-0085
-
192991-0041
192991-0047
192991-0059
-
20
Tin
Gold flash
Gold
192991-0166
192991-0163
192991-0164
-
192991-0211
192991-0078
192991-0207
-
16
Tin
Gold flash
Gold
192991-0162
192991-0159
192991-0160
-
192991-0212
192991-0079
192991-0208
-
.043 (1.10)
.043 (1.10)
.03 (.76)
.03 (.76)
.028 (.71)
.028 (.71)
.059 (1.50)
Tin
Gold
Tin
Gold
Tin Signal
Gold Signal
Tin Power
192991-0198
192991-0195
192991-0122
192991-0119
192900-0465
192900-0356
192991-0617
-
192991-0204
192991-0067
192991-0203
192991-0066
-
-
16-18
14-16
12-14
Tin
Tin
Tin
031-8717-020
031-8717-021
031-8717-022
121668-0000
121668-0001
121668-0002
031-8717-120
031-8717-121
031-8717-122
121668-0100
121668-0101
121668-0102
192945-4930
192945-4380
-
STAMPED CRIMP
13 Amp-200 insertions
MACHINED CRIMP
13 Amp-500 insertions
MACHINED SOLDER FOR PROTOTYPING
28-14 AWG WIRE
Pin
Socket
Tin
192900-0632
192900-0634
Gold
192900-0633
192900-0635
FIRST MATE/LAST BREAK MACHINED CRIMP
13 Amp-500 insertions
PRINTED CIRCUIT BOARD CONTACTS
13 Amp-500 insertions
PC post dia. inches(mm)
Stamped PC pin contacts available,
please contact us
POWER STAMPED 30 Amp-200 insertions
COAX/TWISTED PAIR Used only in signal contact cavities
Outer Female Contact Assembly
Outer Male Contact Assembly
Twisted Pair (B)
Coaxial (A)
Gold
192945-4530
192945-4390
-
Shaded rows = Neptune Version - Supplied with individual wire seal.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
(1) Loose or 3K Reel
Stamped contacts are available loose piece or on
continuous reels of 3,000 for use with semi-automated
crimping systems. Contact us for information.
48
(2) Wire Hole Fillers (Neptune only)
The rear Neptune wire seal has individual wire seals
that are punched out when inserting the contact. If a
seal is accidentally pierced, the seal can be repaired by
inserting a wire hole filler.
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
(3) Keying Pins
A plastic pin which can be snapped into an unused
signal or power contact hole. This will only allow
another connector to mate if there is an empty hole
opposite the keying pin. Used to polarize similar
connectors to avoid mis-mating.
COLUMN 8
ACCESSORIES
COLUMN 9
COLUMN 10
TOOLS
COLUMN 11
WIRE STRIP
WIRE INSULATION
WIRE HOLE
LENGTHS INCHES
DIAMETER
FILLERS
KEYING PINS(3)
(MM) +.02 +.01
INCHES (MM)
NEPTUNE ONLY(2)
COLUMN 12
COLUMN 13
AUTOMATIC CRIMP
TOOLING a PAGE 59
COLUMN 14
COLUMN 15
ECONOMY NONEXTRACTION
RATCHETING HAND
TOOL(6)
CRIMP TOOL(5)
HAND CRIMP TOOL(4)
.035 - .0627
(.89 - 1.58)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
.16 (4.0)
.046 - .081
(1.17 - 2.08)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
.16 (4.0)
.078 - .118
(2.00 - 3.00)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
121586-5237
(16-18 AWG)
.22 (5.6)
N/A
No insulation grip
192991-0018
192991-0018
192991-0018
192991-0018
192991-0018
192991-0018
121586-5238
(14-16 AWG)
.20 (5.0)
.035 - .055
(.90 - 1.40)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.20 (5.0)
.041 - .062
(1.05 - 1.60)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.20 (5.0)
.062 - .084
(1.60 - 2.15)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.20 (5.0)
.051 - .070
(1.30 - 1.80)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.20 (5.0)
.062 - .082
(1.60 - 2.10)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.28 (7.1)
N/A
No insulation grip
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.20 (5.0)
.062 - .082
(1.60 - 2.10)
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
.28 (7.1)
N/A
No insulation grip
192991-0018
192991-0018
192991-0018
192990-0000
192990-0000
192990-0000
AF8
AF8
AF8
TH499
TH499
TH499
-
192922-1450
192922-1450
192922-1450
-
-
-
192922-1450
192922-1450
192922-1450
192922-1450
-
.16 (4.0)
192922-1450
192922-1450
192922-1450
121586-5236
(20-26 AWG)
192922-1440
192922-1450
192922-1450
192922-1450
192922-1450
192922-1450
192922-1450
192922-1450
192922-1450
192922-1450
LOCATOR(4)
N/A
N/A
.20 (5.0)
.055-.079 (1.4 - 2.0)
.079-.114 (2.0 - 2.9)
.114-.142 (2.9 - 3.6)
-
192990-0010 pin
192990-7650 skt
HAND CRIMP TOOL (4)
192991-0019
192991-0019
192991-0019
Contact us for data sheet containing wire preparation information,
tooling, and cable types.
(4) Hand Crimp Tool & Locator
Hand crimp tools produce consistent, high quality
crimps by using a ratchet mechanism which will only
release the contact when the crimp is completed.
Stamped contacts use a tool with integrated
dies. Machined contacts use a military style tool
(MIL-C-22520/1) which also requires the appropriate
locator to form a complete crimping system.
192990-0189
192990-0189
192990-0189
112108-0012
112108-0012
112108-0011
HAND CRIMP TOOL (4)
LOCATOR(4)
Inner Conductor AFM8
K151
Outer Conductor GS100-1
(5) Economy Crimp Tool (stamp contacts only)
This is a pliers-style tool for prototype or service use. It
has no ratchet and the completed crimp requires two
separate operations, one to crimp the conductor and
a second crimp to secure the insulation support. The
economy tool covers wire gauges 16, 20 and 24 AWG
and is for use with stamped contacts only.
192922-1440
192922-1440
-
192900-0176
192900-0176
192900-0176
-
192922-1450
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
WIRE RANGE
GP295
(6) Extraction Tool
Contacts can be easily removed by placing the
extraction tool over the contact in the front of the
connector and pushing. The contact is ejected from
the rear of the connector. No insertion tool is needed
for any Trident contacts.
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
49
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
TRIDENT NEPTUNE METAL (TNM)
192993-0105
Plug (sockets)
no ground
192993-0106
Receptacle (pin)
192993-0109
Plug (sockets)
ground used with
031-8625-011
031-2048-000
Special socket and ground screw
TNM 700 Volt Power Connector System Shell Size 16
The TNM range of connectors is an extension of the long-established Neptune and Trident Ringlock connector series but with a number of
additional features. These include RF shielding and moisture sealing to IP67.
The connectors feature strong nickel-plated zinc alloy shells with a metal coupling ring for high reliability and durability. When used with the new
low cost shielded endbells, the connector system provides RF shielding from cable to equipment or cable to cable that satisfy EMC requirements.
The signal contacts are from the standard Trident contact range a See page 48-49. The recommended contacts are the stamped
and formed Two Part, available with either tin or gold-plated finish. If a higher performance is required, the Trident Three Part machined contacts
can be used. All signal contacts have a current rating of 13 Amps and wires with conductors 14 - 28AWG (2.50 mm2 -.08 mm2) can be
accommodated. Note if more than 4 contacts per connector are designed to run at, or near, their full rated current for sustained periods,
a derating factor must be applied. For further details, please contact us.
LAYOUTS
TYPE
0-4
0-8
0-12
Solder
Crimp 8-10Awg
Crimp 12-14Awg
Crimp 16-18Awg
0-19
Mating face of plug for standard sex is shown. Reverse sex
has mirror image cavity identification.
Sealed Plug
STANDARD SEX
4
4†
8
8†
12
12†
19
19†
10
10
12
12
14
14
16
16
192993-0011
192993-0001
192993-0012
192993-0002
192993-0013
192993-0003
192993-0014
192993-0004
DM53745-28
DM130338-1
DM130339-1
DM130340-1
Unsealed Plug †
Unsealed Flanged Receptacle †
FLANGED
RECEPTACLE
(SOCKETS)
192993-0031
192993-0021
192993-0032
192993-0022
192993-0033
192993-0023
192993-0034
192993-0024
REVERSE SEX
PLUG (SOCKETS)
192993-0051
192993-0041
192993-0052
192993-0042
192993-0053
192993-0043
192993-0054
192993-0044
FLANGED
RECEPTACLE
(PINS)
192993-0071
192993-0061
192993-0072
192993-0062
192993-0073
192993-0063
192993-0074
192993-0064
WIRE SEALING
RANGE FOR
SEALED VERSIONS
INCHES (MM)
GASKETS
STANDARD
PLASTIC
UNSEALED
ENDBELL
.055 (1.4) - .086 (2.2)
No Wire Seal
.055 (1.4) - .086 (2.2)
No Wire Seal
.055 (1.4) - .086 (2.2)
No Wire Seal
.055 (1.4) - .086 (2.2)
No Wire Seal
075-8543-011
075-8543-011
075-8543-012
075-8543-012
192900-0565
192900-0565
192900-0566
192900-0566
192900-0639
192900-0639
192900-0640
192900-0640
192900-0286
192900-0286
192900-0343
192900-0343
† Without wire seal but waterproof to IP67 when used with waterproof endbell.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
50
40
40
20
10
MATES
WITH
MATES
WITH
PLUG (PINS)
DM53744-21
DM130341-1
DM130342-1
DM130343-1
See Technical Specifications a See page 40-41.
Sealed Flanged Receptacle
NUMBER OF SHELL
CONTACTS
SIZE
POWER CONTACT TNM 700 VOLTS ONLY
SOCKETS
PINS
AMP MAX.
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
192993-009_
192993-008_
Low Cost Shielded Gland Seal Endbell
In order to meet EMC requirements, it is necessary to fit a shielded endbell to the TNM connector. The TNM Shielded Gland Seal Endbell
provides for a simple and effective way to terminate, shield and properly seal round jacketed cables. Contact us for right angle extenders
S4810 or for dimensional drawings.
SHELL SIZE
10
12
14
16
PART NUMBER
192993-0081
192993-0082
192993-0083
192993-0084
A
B
2.228 (56.6)
2.232 (56.7)
2.244 (57.0)
2.260 (57.4)
.315 (8.0)
.394 (10.0)
.449 (11.3)
.535 (13.6)
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
STEP 1: Slide O ring over connector body and
it will fit into a grove just past the accessory
threading.
STEP 2: Slide clamp nut, cable clamp (note:
cable clamp compression fingers point toward
the connector body), gland seal, (use isopropyl
alcohol to slide rubber gland), metal endbell
body, metal shielding cone and plastic retention
clip, in that order, over your jacketed cable.
STEP 3: Strip back cable jacket as shown.
1.50 inch
(37 mm)
1 inch
(25 mm)
PLASTIC
WATERPROOF
GLAND SEAL
ENDBELL
192900-0637
192900-0637
192900-0496
192900-0496
192900-0497
192900-0497
.50 inch
(12 mm)
C
.512 (13.0)
.630 (16.0)
.748 (19.0)
.866 (22.0)
STEP 4: Terminate and insert contacts per
assembly instructions a on page 58-60.
E (STD.)
3.484 (88.5)
3.484 (88.5)
3.484 (88.5)
3.484 (88.5)
E (REV.)
3.150 (80.0)
3.150 (80.0)
3.150 (80.0)
3.150 (80.0)
STEP 9: Slide the metal endbell body
down the cable and tighten by hand.
STEP 5: Slide plastic retention clip onto
the connector body.
STEP 10: Slide gland seal and cable clamp
down into the back of the metal endbell.
STEP 6: Pull braided cable shield over plastic (Note: isopropyl alcohol will assist in sliding
rubber gland seal on cable).
retention clip.
STEP 11: Tighten endbell with appropriate
STEP 7: Slide metal shielding cone down
wrench and endbell assembly tools.
until it snaps on to the plastic retention clip.
STEP 12: Push the cable grip up against
the gland seal, then thread clamp nut onto
endbell body and tighten to 10Nm
STEP 8: Fold remaining braided cable shield +/-1Nm (88.50 inch/pounds).
back over the metal shielding cone.
The braided cable shield should now be
captured between the plastic retention clip
and metal shielding cone.
CABLE JACKET
SHIELDED METAL
CABLE JACKET
SEALING RANGE FOR
WATERPROOF
SEALING RANGE FOR
PLASTIC ENDBELL
GLAND SEAL
METAL SHIELDED
INCHES (MM)
ENDBELL
ENDBELL INCHES (MM)
.224 (5.7)-.366 (9.3)
.224 (5.7)-.366 (9.3)
.256 (6.5)-.488 (12.4)
.256 (6.5)-.488 (12.4)
.256 (6.5)-.630 (16.0)
.256 (6.5)-.630 (16.0)
D
.705 (17.9)
.827 (21.0)
.945 (24.0)
1.079 (27.4)
192993-0082
192993-0092
192993-0083
192993-0093
192993-0084
192993-0094
.252 (6.4)-.374 (9.5)
.236 (6.0)-.472 (12.0)
.272 (6.9)-.402 (10.2)
.275 (7.0)-.551 (14.0)
.311 (7.9)-.496 (12.6)
.314 (8.0)-.629 (16.0)
RECEPTACLE
METAL DUST CAP
RECEPTACLE
PLASTIC DUST CAP
METAL PLUG
DUST CAP
192990-1490
192990-1490
192922-1500
192922-1500
192922-1510
192922-1510
192900-0377
192900-0377
192900-0378
192900-0378
192900-0379
192900-0379
MS3180-12CA
MS3180-12CA
MS3180-14CA
MS3180-14CA
MS3180-16CA
MS3180-16CA
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
TRIDENT NEPTUNE METAL (TNM)
† Without wire seal but waterproof to IP67 when used with waterproof endbell.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
51
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
52
DIMENSIONS
TNM STANDARD PLUG
GLAND NUT SECURING
RUBBER SEAL
NUMBER OF CONTACTS
SHELL SIZE
PART NUMBER
A
B
C
D
4
10
192993-0011
1.673 (42.5)
.580 (14.7)
.689 (17.5)
.850 (21.6)
4†
10
192993-0001
1.500 (38.1)
.580 (14.7)
.543 (13.8)
.850 (21.6)
8
12
192993-0012
1.673 (42.5)
.580 (14.7)
.811 (20.6)
.976 (24.8)
8†
12
192993-0002
1.500 (38.1)
.580 (14.7)
.665 (16.9)
.976 (24.8)
12
14
192993-0013
1.673 (42.5)
.580 (14.7)
.957 (24.3)
1.102 (28.0)
12†
14
192993-0003
1.500 (38.1)
.580 (14.7)
.791 (20.1)
1.102 (28.0)
19
16
192993-0014
1.673 (42.5)
.580 (14.7)
1.063 (27.0)
1.229 (31.2)
19†
16
192993-0004
1.500 (38.1)
† Dimensions without wire seal and standard wire seal endbell.
.580 (14.7)
.917 (23.3)
1.229 (31.2)
TNM STANDARD FLANGED RECEPTACLES
GLAND NUT
SECURING
RUBBER SEAL
NUMBER OF
SHELL SIZE
CONTACTS
Dim. J-flange in front of panel
Dim. K-flange at rear of panel
INTERFACE
SEAL
PART
NUMBER
A
C
D
F
G
H
J
K
.937 (23.79)
.719 (18.26)
.126 (3.2)
.594 (15.1)
.681 (17.3)
4
10
192993-0031
1.366 (34.7)
.689 (17.5)
.587 (14.92)
4†
10
192993-0021
1.193 (30.3)
.563 (14.3)
.587 (14.92)
.937 (23.79)
.719 (18.26)
.126 (3.2)
.594 (15.1)
.681 (17.3)
8
12
192993-0032
1.366 (34.7)
.811 (20.6)
.747 (18.98)
1.030 (26.15)
.812 (20.62)
.126 (3.2)
.717 (18.2)
.858 (21.8)
8†
12
192993-0022
1.193 (30.3)
.685 (17.4)
.747 (18.98)
1.030 (26.15)
.812 (20.62)
.126 (3.2)
.717 (18.2)
.858 (21.8)
12
14
192993-0033
1.366 (34.7)
.957 (24.3)
.872 (22.16)
1.124 (28.54)
.898 (22.80)
.138 (3.5)
.843 (21.4)
.984 (25.0)
12†
14
192993-0023
1.193 (30.3)
.811 (20.6)
.872 (22.16)
1.124 (28.54)
.898 (22.80)
.138 (3.5)
.843 (21.4)
.984 (25.0)
19
16
192993-0034
1.366 (34.7)
1.063 (27.0)
.997 (25.33)
1.216 (30.89)
.969 (24.61)
.138 (3.5)
.969 (24.6)
1.106 (28.1)
19†
16
192993-0024 1.193 (30.3)
.937 (23.8)
.997 (25.33) 1.216 (30.89) .969 (24.61)
† Dimensions without wire seal and standard wire seal endbell.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
.138 (3.5)
.969 (24.6)
1.106 (28.1)
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
TNM REVERSED PLUG
D
GLAND NUT
SECURING
RUBBER SEAL
NUMBER OF CONTACTS
SHELL SIZE
PART NUMBER
A
B
C
D
4
10
192993-0051
1.346 (34.2)
.580 (14.7)
.689 (17.5)
.850 (21.6)
4†
10
192993-0041
1.173 (29.8)
.580 (14.7)
.543 (13.8)
.850 (21.6)
8
12
192993-0052
1.346 (34.2)
.580 (14.7)
.811 (20.6)
.976 (24.8)
8†
12
192993-0042
1.173 (29.8)
.580 (14.7)
.665 (16.9)
.976 (24.8)
12
14
192993-0053
1.346 (34.2)
.580 (14.7)
.957 (24.3)
1.102 (28.0)
12†
14
192993-0043
1.173 (29.8)
.580 (14.7)
.791 (20.1)
1.102 (28.0)
19
16
192993-0054
1.346 (34.2)
.580 (14.7)
1.063 (27.0)
1.229 (31.2)
19†
16
192993-0044
1.173 (29.8)
† Dimensions without wire seal and standard wire seal endbell.
.580 (14.7)
.917 (23.3)
1.229 (31.2)
TNM REVERSED FLANGED RECEPTACLES
GLAND NUT
SECURING
RUBBER SEAL
NUMBER OF
SHELL SIZE
CONTACTS
Dim. J-flange in front of panel
Dim. K-flange at rear of panel
INTERFACE
SEAL
PART
NUMBER
A
C
D
F
G
H
J
K
.937 (23.79)
.719 (18.26)
.126 (3.2)
.594 (15.1)
.681 (17.3)
4
10
192993-0071
1.693 (43.0)
.689 (17.5)
.587 (14.92)
4†
10
192993-0061
1.520 (38.6)
.563 (14.3)
.587 (14.92)
.937 (23.79)
.719 (18.26)
.126 (3.2)
.594 (15.1)
.681 (17.3)
8
12
192993-0072
1.693 (43.0)
.811 (20.6)
.747 (18.98)
1.030 (26.15)
.812 (20.62)
.126 (3.2)
.717 (18.2)
.858 (21.8)
8†
12
192993-0062
1.520 (38.6)
.685 (17.4)
.747 (18.98)
1.030 (26.15)
.812 (20.62)
.126 (3.2)
.717 (18.2)
.858 (21.8)
12
14
192993-0073
1.693 (43.0)
.957 (24.3)
.872 (22.16)
1.124 (28.54)
.898 (22.80)
.138 (3.5)
.843 (21.4)
.984 (25.0)
12†
14
192993-0063
1.520 (38.6)
.811 (20.6)
.872 (22.16)
1.124 (28.54)
.898 (22.80)
.138 (3.5)
.843 (21.4)
.984 (25.0)
19
16
192993-0074
1.693 (43.0)
1.063 (27.0)
.997 (25.33)
1.216 (30.89)
.969 (24.61)
.138 (3.5)
.969 (24.6)
1.106 (28.1)
19†
16
192993-0064 1.520 (38.6)
.937 (23.8)
.997 (25.33) 1.216 (30.89) .969 (24.61)
† Dimensions without wire seal and standard wire seal endbell.
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
.138 (3.5)
.969 (24.6)
1.106 (28.1)
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
DIMENSIONS
53
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
54
DIMENSIONS
STANDARD PLUG
RINGLOCK
NEPTUNE
A
A
D
B
D
B
C
C
LAYOUT
SHELL SIZE
STANDARD PLUG
A
0-4
10
192922-1250
0-7
18
192922-1330
0-8
12
192922-1260
0-12
14
192922-1270
0-12
14
192900-0303
2-13
16
192900-0507
0-19
16
192922-1280
0-19
16
192900-0017
0-23
18
192990-1320
4-20
24
192900-0014
0-28
20
192922-1290
12-19
24
192900-0016
4-28
24
192900-0015
0-35
22
192922-1300
0-48
24
192990-1340
0-48
24
192900-0469
0-48 (L)
24
192991-0628
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
B
1.252
1.299
1.252
1.252
1.527
1.566
1.252
1.566
1.252
1.566
1.252
1.566
1.566
1.252
1.252
1.566
2.000
C
0.756
0.756
0.756
0.756
0.756
0.751
0.751
0.756
0.756
0.580
0.751
0.756
0.756
0.580
0.756
0.756
0.756
D
0.429
0.885
0.543
0.669
0.956
1.063
0.783
1.063
0.881
1.594
1.007
1.594
1.594
1.122
1.248
1.594
1.594
0.850
1.350
0.976
1.102
1.102
1.189
1.228
1.189
1.350
1.732
1.476
1.732
1.732
1.602
1.728
1.732
1.732
STANDARD FLANGED RECEPTACLE
RINGLOCK
NEPTUNE
A
E
C
B
E
D dia.
A
NUMBER OF
SHELL SIZE
CONTACTS
F
G
B
C
D
G
Dim. J-flange in front of panel
Dim. K-flange at rear of panel
STANDARD
FLANGED
RECEPTACLE
A
B
0-4
10
192990-1660
1.016
0.439
0-7
8
192990-1700
1.280
0.716
0-8
12
192990-1670
1.016
0.447
0-12
14
192990-1680
1.016
0.447
0-12
14
192900-0308
1.563
0.448
2-13
16
192900-0509
1.566
0.448
0-19
16
192990-1690
1.016
0.447
0-19
16
192900-0039
1.566
0.448
0-23
18
192990-1710
1.016
0.447
4-20
24
192900-0030
1.645
0.606
0-28
20
192990-1720
1.311
0.571
12-19
24
192900-0036
1.645
0.606
4-28
24
192900-0033
1.645
0.606
0-35
22
192990-1730
1.311
0.571
0-48
24
192990-1740
1.311
0.602
0-48
24
192900-0475
1.645
0.606
0-48 (L)
24
192991-0640
2.075
0.606
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
C
D
E
F
G
H
J
K
0.433
0.886
0.547
0.673
0.956
1.063
0.787
1.063
0.886
1.578
1.012
1.578
1.578
1.126
1.252
1.578
1.578
0.591
1.122
0.748
0.874
0.874
1.000
1.000
1.000
1.122
1.500
1.248
1.500
1.500
1.374
1.500
1.500
1.500
0.091
0.098
0.091
0.091
0.091
0.091
0.091
0.091
0.098
0.138
0.098
0.138
0.138
0.138
0.138
0.138
0.138
0.925
1.311
1.031
1.108
1.122
1.220
1.200
1.220
1.311
2.000
1.437
2.000
2.000
1.563
1.689
2.000
2.000
0.709
1.063
0.807
0.890
0.901
0.964
0.953
0.964
1.059
1.563
1.150
1.563
1.563
1.244
1.356
1.563
1.563
0.128
0.128
0.128
0.128
0.126
0.126
0.128
0.126
0.128
0.165
0.128
0.165
0.165
0.128
0.154
0.165
0.165
0.594
1.094
0.717
0.842
0.968
1.106
0.968
1.106
1.094
1.614
1.216
1.614
1.614
1.342
1.468
1.614
1.614
0.681
1.232
0.858
0.984
0.968
1.106
1.106
1.106
1.232
1.614
1.358
1.614
1.614
1.484
1.610
1.614
1.614
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
F
STANDARD JAM NUT RECEPTACLE
NEPTUNE ONLY
A
F
B
E
H
C
D
G
J
SHELL
SIZE
STANDARD JAM
NUT RECEPTACLE
A
B
C
D
E
F
G
H
J
192900-0313
1.563
0.870
0.956
0.874
0.138
1.410
1.267
0.988
1.075
0-19
16
192900-0490
1.565
0.905
1.063
1.000
0.090
1.566
1.511
1.102
1.200
2-13
16
192900-0508
1.565
0.905
1.063
1.000
0.090
1.566
1.511
1.102
1.200
4-20
24
192900-0032
1.646
0.921
1.579
1.500
0.138
2.008
1.870
1.634
1.701
12-19
24
192900-0038
1.646
0.921
1.579
1.500
0.138
2.008
1.870
1.634
1.701
4-28
24
192900-0035
1.646
0.921
1.579
1.500
0.138
2.008
1.870
1.634
1.701
0-48 (L)
24
192991-0644
2.075
0.921
1.579
1.500
0.138
2.008
1.870
1.634
1.701
0-48
24
192900-0481
1.646
0.921
1.579
1.500
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
0.138
2.008
1.870
1.634
1.701
LAYOUT
0-12
14
REVERSE PLUG
RINGLOCK
NEPTUNE
A
A
B
A
B
C
C
LAYOUT
SHELL SIZE
REVERSE PLUG
A
B
C
D
0-4
10
192926-0500
1.027
0.752
0.433
0.850
0-8
12
192926-0510
1.008
0.752
0.547
0.976
0-12
14
192926-0520
1.055
0.752
0.673
1.102
0-12
14
192900-0236
1.244
0.752
0.957
1.102
0-19
16
192926-0530
1.087
0.752
0.787
1.228
0-19
16
192900-0057
1.248
0.752
1.063
1.189
2-13
16
192900-0581
1.248
0.752
1.063
1.189
0-7
18
192990-1390
1.240
0.752
0.885
1.350
0-23
18
192990-1380
1.008
0.752
0.885
1.350
0-28
20
192926-0540
1.232
0.752
1.011
1.476
0-35
22
192926-0550
1.232
0.752
1.126
1.602
4-20
24
192900-0054
1.275
0.580
1.594
1.732
12-19
24
192900-0056
1.275
0.580
1.594
1.732
4-28
24
192900-0055
1.275
0.580
1.594
1.732
0-48 (L)
24
192991-0648
1.693
0.580
1.594
1.732
0-48
24
192900-0425
1.275
0.580
1.594
1.732
1.232
0.580
1.225
1.728
0-48
24
192990-1400
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
DIMENSIONS
55
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
DIMENSIONS
REVERSE FLANGED RECEPTACLE
RINGLOCK
NEPTUNE
G
B
E
C
D
G
F
Dim. J-flange in front of panel
Dim. K-flange at rear of panel
LAYOUT
REVERSE
FLANGED
RECEPTACLE
SHELL SIZE
A
B
C
D
0-4
10
192990-1760
1.24
0.447
0.433
0.591
0-7
18
192990-1800
1.346
0.700
0.886
1.122
0-8
12
192990-1770
1.240
0.447
0.547
0.748
0-12
14
192990-1780
1.240
0.447
0.673
0.874
0-12
14
192900-0256
1.563
0.448
0.956
0.874
2-13
16
192900-0582
1.566
0.448
1.063
1.000
0-19
16
192990-1790
1.240
0.447
0.787
1.000
0-19
16
192900-0078
1.566
0.448
1.063
1.000
0-23
18
192990-1810
1.240
0.447
0.886
1.122
4-20
24
192900-0069
1.646
0.606
1.578
1.500
0-28
20
192990-1820
1.299
0.573
1.012
1.248
12-19
24
192900-0075
1.646
0.606
1.578
1.500
4-28
24
192900-0072
1.646
0.606
1.578
1.500
0-35
22
192990-1830
1.299
0.573
1.126
1.374
0-48
24
192990-1840
1.370
0.604
1.252
1.498
0-48
24
192900-0431
1.646
0.606
1.578
1.500
0-48 (L)
24
192991-0652
2.075
0.606
1.578
1.500
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
E
F
G
H
J
K
0.091
0.091
0.091
0.091
0.090
0.090
0.091
0.090
0.098
0.137
0.098
0.137
0.137
0.138
0.138
0.137
0.137
0.925
1.311
1.031
1.108
1.122
1.220
1.200
1.220
1.311
2.000
1.437
2.000
2.000
1.563
1.689
2.000
2.000
0.709
1.063
0.807
0.890
0.901
0.964
0.953
0.964
1.059
1.563
1.150
1.563
1.563
1.244
1.356
1.563
1.563
0.128
0.128
0.128
0.128
0.126
0.126
0.128
0.126
0.128
0.165
0.128
0.165
0.165
0.128
0.154
0.165
0.165
0.594
1.094
0.717
0.843
0.968
1.106
0.969
1.106
1.094
1.614
1.217
1.614
1.614
1.343
1.469
1.614
1.614
0.681
1.232
0.858
0.984
0.968
1.106
1.106
1.106
1.232
1.614
1.358
1.614
1.614
1.484
1.610
1.614
1.614
REVERSE JAM NUT RECEPTACLE
NEPTUNE ONLY
A
E
F
B
H
C
D
G
J
LAYOUT
SHELL SIZE
REVERSE JAM NUT
RECEPTACLE
A
B
C
0-12
14
192900-0266
1.563
0.870
0.956
2-13
16
192900-0583
1.566
0.905
1.063
0-19
16
192900-0353
1.566
0.905
1.063
4-20
24
192900-0071
1.645
0.921
1.578
12-19
24
192900-0077
1.645
0.921
1.578
4-28
24
192900-0074
1.645
0.921
1.578
0-48
24
192900-0437
1.646
0.921
1.578
0-48 (L)
24
192991-0656
2.075
0.921
1.578
All dimensions are in inches.
Shaded rows = Neptune Version - Supplied with individual wire seal
56
F
A
D
E
F
G
H
J
0.874
1.000
1.000
1.500
1.500
1.500
1.500
1.500
0.137
0.090
0.090
0.137
0.137
0.137
0.137
0.137
1.409
1.212
1.212
2.007
2.007
2.007
2.007
2.007
1.267
1.503
1.503
1.870
1.870
1.870
1.870
1.870
0.988
1.102
1.102
1.633
1.633
1.633
1.633
1.633
1.075
1.200
1.200
1.700
1.700
1.700
1.700
1.700
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
SEALED CABLE CLAMPS FOR USE WITH JACKETED CABLES
Cable
Clamp
* For disassembly add .354 (9.0) for Shell Sizes
10-16 & .417 (10.6) for Shell Sizes 18-24
Rubber gland seal perforated for
entire insulation range
Body
B
dia.
C
A/F
Metal washers
A (assembled)
SHELL SIZE
PART #
*D (to panel)
DIMENSIONS
A MAX
B MAX
C+ .007 (.20)
WIRE SEALING DIAMETER INCHES (MM)
D MAX
10
192990-1530
2.165 (55.0)
.437 (11.1)
.740 (18.8)
3.011 (76.5)
12
192990-1540
2.283 (58.0)
.535 (13.6)
.818 (20.8)
3.063 (77.8)
14
192990-1550
2.559 (65.0)
.574 (14.6)
.897 (22.8)
3.366 (85.5)
14
192900-0496
2.559 (65.0)
.574 (14.6)
.897 (22.8)
3.366 (85.5)
16
192990-1560
2.716 (69.0)
.653 (16.6)
.972 (24.7)
3.535 (89.8)
16
192900-0497
2.716 (69.0)
.653 (16.6)
.972 (24.7)
3.535 (89.8)
18
192990-1570
2.874 (73.0)
.653 (16.6)
.972 (24.7)
3.661 (93.0)
20
192990-1580
3.267 (83.0)
.870 (22.1)
1.252 (31.8)
4.232 (107.5)
22
192990-1590
3.543 (90.0)
.870 (22.1)
1.252 (31.8)
4.507 (114.5)
24
192990-1600
4.133 (105.0)
1.165 (29.6)
1.645 (41.8)
5.059 (128.5)
24
192900-0498
4.133 (105.0)
1.165 (29.6)
1.645 (41.8)
5.059 (128.5)
Shaded rows = Neptune Version - Supplied with individual wire seal
MAX.
MIN.
.354 (9.0)
.366 (9.3)
.488 (12.4)
.488 (12.4)
.488 (12.4)
.488 (12.4)
.630 (16.0)
.748 (19.0)
.748 (19.0)
1.040 (26.5)
1.040 (26.5)
.165 (4.2)
.224 (5.7)
.256 (6.5)
.256 (6.5)
.256 (6.5)
.256 (6.5)
.256 (6.5)
.362 (9.2)
.362 (9.2)
.670 (17.0)
.670 (17.0)
REAR THREAD
PG 9
PG 11
PG 13.5
PG 13.5
PG 16
PG 16
PG 16
PG 21
PG 21
PG 29
PG 29
UNSEALED CABLE CLAMPS - STRAIN RELIEF AND WIRE PROTECTION
* For disassembly add .354 (9.0) for Shell Sizes
10-16 & .417 (10.6) for Shell Sizes 18-24
B
C
SHELL SIZE
A
PART #
D
E dia.
3 clamps for full
range of cable
dimensions
* F (to panel)
DIMENSIONS
A+ .005 (.15)
B MAX
C+ .005 (.15)
10
192922-1310
1.570 (39.9)
.846 (21.5)
.251 (6.4)
12
192922-1320
1.574 (40.0)
.980 (24.9)
.251 (6.4)
14
192922-1330
1.811 (46.0)
1.063 (27.0)
.251 (6.4)
14
192900-0286
1.811 (46.0)
1.063 (27.0)
.251 (6.4)
16
192922-1340
1.811 (46.0)
1.185 (30.1)
.251 (6.4)
16
192900-0343
1.811 (46.0)
1.185 (30.1)
.251 (6.4)
18
192990-1510
1.968 (50.0)
1.259 (32.0)
.275 (7.0)
20
192922-1350
2.165 (55.0)
1.350 (34.3)
.275 (7.0)
22
192922-1360
2.362 (60.0)
1.460 (37.1)
.322 (8.2)
24
192990-1520
2.559 (65.0)
1.645 (41.8)
.322 (8.2)
24
192900-0344
2.559 (65.0)
1.645 (41.8)
.322 (8.2)
Shaded rows = Neptune Version - Supplied with individual wire seal
D MAX
.342 (8.7)
.503 (12.8)
.543 (13.8)
.543 (13.8)
.669 (17.0)
.669 (17.0)
.783 (19.9)
.826 (21.0)
.905 (23.0)
1.063 (27.0)
1.102 (28.0)
E+ .005 (.15)
.826 (21.0)
.944 (24.0)
1.063 (27.0)
1.063 (27.0)
1.189 (30.2)
1.189 (30.2)
1.307 (33.2)
1.433 (36.4)
1.559 (39.6)
1.685 (42.8)
1.673 (42.5)
F MAX
2.413 (61.3)
2.413 (61.3)
2.641 (67.1)
2.641 (67.1)
2.641 (67.1)
2.641 (67.1)
2.787 (70.8)
3.122 (79.3)
3.358 (85.3)
3.574 (90.8)
3.574 (90.8)
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
DIMENSIONS
RINGLOCK ADAPTERS FOR HEAT SHRINK BOOTS OR SLEEVING
SHELL
SIZE
PART #
A
DIMENSIONS (MAX)
B
C
H THREAD
10
192990-1430
.827 (21.0)
.712 (18.1)
.755 (19.2)
9/16-24UNEF-2B
12
192990-1440
.944 (24.0)
.921 (23.4)
.755 (19.2)
11/16-24UNEF-2B
14
192990-1450
1.063 (27.0)
.952 (24.2)
.755 (19.2)
13/16-20UNEF-2B
16
192990-1460
1.189 (30.2)
1.165 (29.6)
.846 (21.5)
15/16-20UNEF-2B
18
192990-1470
1.311 (33.3)
1.248 (31.7)
.846 (21.5)
1-1/16-18UNEF-2B
20
192990-1480
1.437 (36.5)
1.409 (35.8)
.897 (22.8)
1-3/16-18UNEF-2B
22
192990-1490
1.563 (39.7)
1.503 (38.2)
.897 (22.8)
1-5/16-18UNEF-2B
24
192990-1500
1.689 (42.9)
1.626 (41.3)
.862 (21.9)
1-7/16-18UNEF-2B
All dimensions in inches (millimeters in parentheses) unless otherwise stated.
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
57
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
ASSEMBLY INSTRUCTIONS
CRIMP TOOL OPERATION
There are five different crimp tools used with Trident contacts. Find the appropriate tool on the Contact Selection Chart and follow the
instructions for that tool below.
HAND CRIMP TOOL FOR STAMPED CONTACTS
(192990-3140 for 16-28 AWG contacts and 192900-0175 for 14 AWG contacts)
STEP 1: Strip wires to length (See strip
length in Column 8 of contact chart
a on page 49)
STEP 2: Open the tool and select the proper
crimp cavity for the wire gauge.
STEP 3: Hold tool in your right hand with the
die cavity identification facing away from you.
STEP 6: Turn the tool over in your right hand
and insert the stripped wire into the contact
until it bottoms.
STEP 7: Cycle the tool. The tool will not
open until the contact has been completely
crimped.
STEP 8: Inspect the crimp. A contact crimp
verification tool is available. Please contact us.
CONTACT CRIMP TOOL
(121586-5236) (121586-5237) (121586-5238)
STEP 1: Strip wires to length (see strip length
in Column 8 of contact chart a on page 49)
STEP 2: Open the tool and select the proper
crimp cavity for the wire gauge.
STEP 3: Now hold the tool so that the cavity
identification is away from you (the back side).
STEP 4: Surrounding the lower die is a
holding frame; push up on the tab to fully
raise the frame.
STEP 5: While holding the frame open, insert
the power contact wire side first, until the lip
on the contact hits against the ledge of the
lower die. The U-shaped wire crimps should
be upright in the die.
STEP 6: Release the tab. The frame should
now be holding the contact in the proper
cavity, ready to crimp.
STEP 7: Close the tool just enough to grip
the contact.
STEP 8: Insert the stripped wire into the
contact from the wire side.
STEP 9: Cycle the tool. The tool will not
open until the contact has been completely
crimped. An escape lever is located on the
ratchet mechanism to release the tool if
necessary.
STEP 10: Inspect the crimp. See “Stamped
Contacts” in Crimp Inspection section
a on page 60.
ECONOMY TOOL FOR STAMPED CONTACTS
(192922-1440)
STEP 1: Strip wires to length (See strip length
in Column 8 of contact chart a on page 49)
STEP 2: Select the proper crimp cavity for
the wire gauge.
STEP 3: The contact itself has two U-shaped
crimp areas, each requiring a separate crimp
operation. The larger, rear U-shaped area
crimps over the wire insulation and provides
strain relief. The smaller, longer, U-shaped
area crimps over the bare wire and provides
the electrical connection.
58
STEP 4: Pick up the contact by the mating
end. Slip the contact into the appropriate die
cavity so that the notch just behind the “gold”
portion of the contact fits over the sliding
plate on the lower half of the die.
STEP 5: Squeeze the handle just enough to
hold the contact in the die cavity.
STEP 4: Insert the contact into the tool so
that the smaller wire crimp U is upright and
centered in the proper die (the open portion
of the U facing the cavity identification on
the tool).
STEP 5: Close the tool just enough to
firmly grip the contact.
STEP 6: Insert the stripped wire into the
contact until it bottoms.
STEP 7: Cycle the tool.
STEP 8: Remove the crimped contact.
Now you must crimp the insulation grip.
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
STEP 9: Place the insulation U upright in the
die cavity marked INS. Crimp the Insulation
U over the wire insulation in the same manner
as the wire crimp.
STEP 10: Inspect the two crimps. See
“Stamped Contacts” in Crimp Inspection
section a on page 60. A contact crimp
verification tool is available. Please contact us.
CRIMP TOOL FOR MACHINED CONTACTS
There are five different crimp tools used with Trident contacts. Find the appropriate tool on the Contact Selection Chart and follow the
instructions for that tool below.
LOCATOR
LATCH
CRIMP
TOOL
LOCATOR
DIAL
LATCH
LOCK PIN
LOCATOR
COLOR CODE
INDEX
MARK
STEP 1: Strip the wires to length.
STEP 2: Open the crimp tool
by squeezing the handles. Push
the latch on turret to pop up the
locator. Attach the turret to the
crimp tool using the two captive
hex bolts in the turret.
STEP 3: Select the proper
locator position for your contact
by rotating the locator until the
proper color is aligned with the
index mark. Push locator back
down until it snaps into position.
CONTACT TYPE
PINS
SOCKETS
FIRST-MATE
STEP 5: Cycle the tool before
inserting the contact to be sure
the tool is in the open position.
Drop the contact, mating end
first, into the crimp cavity of the
tool. Squeeze the tool handle
just enough to grip the contact
without actually crimping it.
STEP 6: Insert the stripped wire
into the contact with a slight
twisting motion. Be sure all wire
strands are inside the contact.
Squeeze the handle to cycle the
tool. The handle will not release
until the contact is completely
crimped.
TURRET
STEP 4: Adjust dial for proper
wire gauge. To change the dial
setting, remove the lock pin
and lift center of dial. Turn to
the desired wire gauge. Replace
lock pin on dial.
LOCATOR
COLOR
BLUE
GREEN
RED
STEP 7: Remove the crimped
contact. Pull on the wire slightly
to be sure it is properly crimped.
Be sure the contact is not bent
or damaged in any way.
STEP 8: Visually inspect the
crimp. See “machined contacts”
drawing in Visual Check section
on next page.
NEW TRIDENT AUTOMATIC CRIMP TOOLS FOR REELED STAMPED CONTACTS
Mini Applicators modules are used in industry-standard crimp presses. This allows for fast change-over for crimping different contacts.
Using the same crimp press saves valuable factory floor space over multiple presses.
CONTACT
TYPE
20-26
16-18
14-16
Signal
Signal
Signal
MINI APPLICATOR PART NUMBER
METCAL
SCHAFER
121586-5239
121586-5217
121586-5240
121586-5142
121586-5141
Contact us for details
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
ASSEMBLY INSTRUCTIONS
Adjustment fixture for signal applicators 317-8675-133
CONTACT
16-18
14-16
12-14
TYPE
Power
Power
Power
MINI APPLICATOR PART NUMBER
193800-0031
193800-0024
193800-0023
Contact us for detailed crimp specifications.
For assistance in Europe and China, please see the back cover for a complete listing of our branch offices and contact numbers.
Specifications subject to change.
59
single strand
ITT CANNON TRIDENT CONNECTORS: TRIDENT RINGLOCK, TRIDENT NEPTUNE & TNM
ASSEMBLY INSTRUCTIONS
3
2
CRIMP INSPECTION (MICRO SECTIONS)
Enlargement of micro section allows for final judgment of crimp quality. This test is recommended whenever new tools or new types of wire are used.
FOR STAMPED CONTACTS
single strand
1
1
Correct Crimp
4
FOR MACHINED CONTACTS
single strand
5
1
1
1
22
strands not visible
3
2
2
strands extend
too far into contact
1
2
44
strands extend
too far into contact
33
3
1 - Insulation
2 - Strands
3 - Contact
Incorrect Crimp
strands not visible
Incorrect
crimp strand
single
1
single strand 2
2
2
5
44
33
3
1 - Insulation
2 - Strands
3 - Contact
4 - Wire inspection hole
5 - Shoulder
strands must be visible
strands must be visible
through wire inspection
hole (4)
single strand
3
strands must be visible
1
1
Correct
Crimp
Incorrect
crimp
2
3
Incorrect Crimp
Incorrect Crimp
1
2
4
3
not visible
INSERTION
OFstrands
CONTACTS
1
2
No insertion tool is required.
3
STEP 1: Strip wires to length (See strip length in Column 8 of contact chart a on page 49.)
STEP 2: When using Neptune connectors with the rear wire sealing grommet, put the grommet in place on the connector and push the
contact directly through the grommet into the cavity. Start at the center of the layout and work concentrically to the outside edge to eliminate
the possibility of the grommet shifting or bunching during loading.
Wire needles may be used as an assembly aid for use with high density layouts, maximum size wire insulation, or when adding to already
terminated connectors.
For socket contact order: 192900-0606 - signal
For pin contact order: 192900-0605 - signal
For socket contact order: 192900-0608 - power
For pin contact order: 192900-0607 - power
To use, push the point of the needle through the selected hole and check that it has passed through to the correct contact cavity by looking at
the mating face of the connector. Once verified, attach the contact to the non-pointed end of the needle. Holding the point of the contact, push
the contact into the connector body until the contact locks into place. Note: The wiring needle is used as a guide and will not pull the contact
into the connector body. Be sure to inspect the mating face (see 3 below) as the grommet mutes the “feel” of the contact locking into place.
STEP 3: Inspect by looking at the mating side of the connector. Be sure that all of the contacts are on the same plane (fully inserted). If not, use
the extraction tool to remove the contact and re-insert.
EXTRACTION OF CONTACTS
Contacts can be removed from the housings using the appropriate extraction tool. The tool is placed over the mating end of the contact and
the sleeve is rotated slightly as it is pushed into the connector.
IMPORTANT: Make sure the depth indicating line on the tool is even with the mating face of the connector before depressing the plunger to
avoid damage to connector and contact. Light pressure on the plunger then ejects the contact from the rear of the connector.
STEP 1:
Contact in connector
STEP 2:
Extraction tool compresses tines
STEP 3:
Plunger pushes contact out rear of connector
depth
indicating
line
depth indicating lines
plunger
60
1
strands extend
too far into contact
For assistance in North America: +1 800.675.1214 • www.peigenesis.com • sales@peigenesis.com
tines
