217-8516-002

Seite 1 von 14 Assembly instruction CAS25022E APD 6-/7-way Assembly instruction APD 6-/7-way Fixed connector Jam nut receptacle Free connector Fixed connector Flange receptacle APD-1AP6, 6-way for stamped contacts APD-1AP6-EP 6-way for press in contacts APD-1AP7-EP 7-way for press in contacts APD-1AP7, 7-way for stamped contacts No endbell mountable Front panel mounting possible Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 2 von 14 Assembly instruction CAS25022E APD 6-/7-way Content I.) APD 6-/7-way with stamped crimp contacts ..................................................... 3! 1.)! Connector Types ............................................................................................ 3! 2.)! Stamped Crimp Contacts................................................................................ 4! 3.)! Single Wire Seal ............................................................................................. 4! 4.)! Crimp with Hand Crimp Tool........................................................................... 5! 5.)! Crimp with Crimp Machine.............................................................................. 5! 6.)! Insertion and Extraction of Stamped Contacts................................................ 6! II.) Assembly instruction with Press-in Contacts (pin contacts only)................. 7! 1.)! Connector Types ............................................................................................ 7! 2.)! Press-In Contacts (1,6mm)............................................................................. 7! 3.)! Stripping the Cable ......................................................................................... 8! 4.)! Crimp instruction for Press-in Contacts .......................................................... 8! 5.)! Insertion of Press-in Contacts......................................................................... 9! III.) Mounting Cut-out and Accessory .................................................................. 10! 1.)! Mounting Cut-out .......................................................................................... 10! 2.)! Flange Sealing.............................................................................................. 10! 3.)! Metal Flange Support ................................................................................... 10! 4.)! Blanking Plug (Blind seal, wire filler)............................................................. 11! 5.)! Mounting of Jam Nut Receptacle.................................................................. 11! 6.)! Tools for Tighten the Jam Nut ...................................................................... 12! IV.) Product safety and warranty .......................................................................... 13! Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 3 von 14 Assembly instruction CAS25022E APD 6-/7-way I.) APD 6-/7-way with stamped crimp contacts 1.) Connector Types Fixed connector Flange receptacle packaging unit 100 pieces Order number 6-way 7-way Fixed connector Jam nut receptacle Order name. Code Colour 120110-0083 APD-1AP6 1 black (1. contact cavity closed) 121583-0020 APD-1AP7 1 black packaging unit 100 pieces Order number Order name. Code Contact cavity closed Colour 6-way 121583-0061 APD-1CP6 1 black (1. contact cavity closed) 7-way 121583-0019 APD-1CP7 1 black Colour black (1. contact cavity closed) Free connector packaging unit 100 pieces Order number Order name. Code 120110-0024 APD-1BS6 1 121583-0018 APD-1BS7 1 Contact cavity closed 6-way 6-polig 7-way black Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 4 von 14 Assembly instruction CAS25022E APD 6-/7-way 2.) Stamped Crimp Contacts The pin and socket contacts are built of high conductive material. Socket contact, size 1,6mm Order number.: 192900-0001 Crimp diameter: 0,75-1,5mm² Standard plating: tinned 3000 contacts per reel Single contact, order number 192900-0003 Pin contact, size 1,6mm Order number.: 192900-0000 Crimp diameter: 0,75-1,5mm² Standard plating: tinned 3000 contacts per reel Single contact, order number 192900-0002 The contacts get crimped with insulation crimp. The crimping measurements are the same for pin and socket contacts in uncrimped condition. 3.) Single Wire Seal Before skinning the cable, push single wire seal in direction of arrow onto the cable.. (optional) Bestell-Bez. Bestell-Nr. 10GR3940 121667-0022 ∅ 1,4 – 2,0mm grau 10YE3940 121667-0023 ∅ 1,9 – 2,1mm gelb 10RD3940 121667-0024 ∅ 1,2 − 1,6mm rot The single wire sealing is not going to be crimped Single wire seal push to cable Strip end Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 5 von 14 Assembly instruction CAS25022E APD 6-/7-way 4.) Crimp with Hand Crimp Tool Single contacts are going to be crimped with hand crimp tool.. Wire size 16-18 AWG; 0,75–1,5mm² Order number. CHT-Trident 121586-5237 During the processing the crimping specification CAS25047 is to be considered 5.) Crimp with Crimp Machine For high volume production, crimp machinery with interchangeable crimp tool as the Mecal-TT and WWZ-Mecal-EVS (mini applicator) are used. Crimp machine Mecal-TT Press Order name: Mecal-TT Order number: 121586-5225 Order name: WWZ-Mecal-EVS Order number: 121586-5217 Crimp tool (mini applicator) WWZ-Mecal-EVS During the processing the crimping specification CAS25046 is to be considered Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 6 von 14 Assembly instruction CAS25022E APD 6-/7-way 6.) Insertion and Extraction of Stamped Contacts There is no need of insertion tools. A.) The stamped contacts get mounted from the rear panel of the connector into the contact cavity by hand until it snaps in. To the front, the contact is bounded by the shoulder at the contact. B.) Single Wire Seal push into connector housing. (Optional) Extraction The extraction of stamped contacts, pin and socket from the housing occurs from the front with the extraction tool. The extraction tool gets inserted into the contact cavity on the mating face. See picture 1. Eventually the snap springs get clamped and the cable can be pulled out from the cable face. See picture 2. Extraction tool Order number: 192922-1450 Extraction tool picture 1 picture 2 Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 7 von 14 Assembly instruction CAS25022E APD 6-/7-way II.) Assembly instruction with Press-in Contacts (pin contacts only) In addition to the standard contacts also press-in contacts may be used for the APD 6-/ 7-way fixed connector. The pressed-in contacts cannot be exchanged anymore. 1.) Connector Types Fixed connector Flange receptacle Packaging unit: 100 pieces 6-way 7-qay Bestell-Nr. Bestell-Bez. Code Farbe 120110-0020 APD-1AP6-EP 1 black (1. contact cavity closed) 121583-0205 APD-1AP7-EP 1 black Fixed connector Jam nut receptacle Packaging unit: 100 pieces Bestell-Nr. Bestell-Bez. Code Farbe 6-polig Auf Anfrage APD-1CP6-EP 1 black (1. contact cavity closed) 7-polig 121583-0028 APD-1CP7-EP 1 black 2.) Press-In Contacts (1,6mm) Order number: 330-8672-021 (tinned), (0,75-1,5mm²) 330-8672-019 (tinned), (0,35-0,75mm²) With plating, flash plated, on request Packaging unit: 100 pieces Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 8 von 14 Assembly instruction CAS25022E APD 6-/7-way 3.) Stripping the Cable Hand crimp tool The crimping process occurs with a hand crimp tool: tool M22520-1-01 locator CT 120090-163 The crimp adjustment should be read of and adjusted at the locator. Pin contact 330-8672-021 330-8672-019 Hand crimp tool M22520-1-01 Order no.: 995-0001-585 Locator for hand crimp tool CT120090-163 120090-0163 4.) Crimp instruction for Press-in Contacts The stripping length for the press-in contact is 6,0+/0,3mm. Strip it with the proper stripping clamp or stripping machine. The stranded wires must not be damaged during this process. 1.) Strip to the proper length 2.) Add the right locator (turret) to the hand crimp tool 3.) Adjust the crimp diameter with the rotatable scale (see note Turret) 4. Place the contact in the locator and insert the stripped cable into the contact 5.) Press the clamp until reopening is possible 6.) Remove and check the contact crimp. Check the accurate position of the stranded wires through the visual holes. Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 9 von 14 Assembly instruction CAS25022E APD 6-/7-way Crimp error All right! Cable insulation Stranded wire Contact Visual hole Wrong Loose stranded The minimum retention force are fixed in the standard DIN EN 60352-2-2006 These depend to consider on the cable diameter. 5.) Insertion of Press-in Contacts After having crimped, the press-in contact gets inserted into the insulator from the cable face (contact cavity). With the insertion tool CIT-APD-16 TIP that is integrated in the hand gear press, the press-in contact gets pressed-in until catch (control measurement 4,1mm). The insertion tool has to press on the shoulder of the contact during process Order name: Hand gear press CHPZ-240 Insertion tool CIT-APD-16 TIP Order umber: 121586-0081 317-8648-008 Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 10 von 14 Assembly instruction CAS25022E APD 6-/7-way III.) Mounting Cut-out and Accessory 1.) Mounting Cut-out Mounting cut-out for all APD 6-/7-way fixed connectors, Flange receptacles. The thread in the bulkhead conforms with the max. torque for M3 screws. or M3 Mounting cut-out for all APD 6-/7-way fixed connectors, Jam nut receptacle. 2.) Flange Sealing Order number.: 075-8503-000 Seal O-Ring groove Rear panel mounting Flange sealing, rubber, for sealing the flange receptacle. The sealing gets mounted from the mating face. Front panel mounting An O-Ring is used for front panel mounting. O-Ring Inappropriate for 121583-0020 APD-1AP7 (for Trident contacts). 3.) Metal Flange Support Order number.: 066-8516-005 Flange support for all fixed connectors, flange receptacles. The flange gets inserted from the mating face with its plane surface (rear panel) pressing the flange of the receptacle (front panel mounting). Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 11 von 14 Assembly instruction CAS25022E APD 6-/7-way 4.) Blanking Plug (Blind seal, wire filler) For empty contact cavities, there are blanking plugs for sealing. Insert the blanking plug as shown in the draft final position. final position blanking plug Contact cavity backside Order name: 10WH3940 Order number: 121667-0025 5.) Mounting of Jam Nut Receptacle Jam nut receptacle housing Jam nut Standard: 217-8516-002 Special: 217-8516-001 Torque: 6 +1 Nm O-Ring Schottwanddicke Standard: 1,0 – 4,0mm Special: 2,0 – 5,0mm HNBR, ∅31,5 x 3 Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 12 von 14 Assembly instruction CAS25022E APD 6-/7-way 6.) Tools for Tighten the Jam Nut Order number: 317-8649-034 Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 13 von 14 Assembly instruction CAS25022E APD 6-/7-way IV.) Product safety and warranty THIS NOTE MUST BE READ IN CONJUNCTION WITH THE PRODUCT DATA SHEET/CATALOG. Failure to observe the advice in this information sheet and the operating conditions specified in the Product Data Sheet/Catalog could result in hazardous situations. MATERIAL CONTENT AND PHYSICAL FORM Electrical connectors do not usually contain hazardous materials. They contain conducting and non-conducting materials and can be divided into two groups. a) Printed circuit types and low cost audio types which employ all plastic insulators and casings. b) Rugged, Fire Barrier and High Reliability types with metal casings and either natural rubber, synthetic rubber, plastic or glass insulating materials. Contact materials vary with type of connector and also application and are usually manufactured from either: Copper, copper alloys, nickel, alumel, chromel or steel. In special applications, other alloys may be specified. FIRE CHARACTERISTICS AND ELECTRIC SHOCK HAZARD There is no fire hazard when the connector is correctly wired and used within the specified parameters. Incorrect wiring or assembly of the connector or careless use of metal tools or conductive fluids, or transit damage to any of the component parts may cause electric shock or burns. Live circuits must not be broken by separating mated connectors as this may cause arcing, ionisation and burning. Heat dissipation is greater at maximum resistance in a circuit. Hot spots may occur when resistance is raised locally by damage, e.g. cracked or deformed contacts, broken strands of wire. Local overheating may also result from the use of the incorrect application tools or from poor quality soldering or slack screw terminals. Overheating may occur if the ratings in the product Data Sheet/Catalog are exceeded and can cause breakdown of insulation and hence electric shock. If heating is allowed to continue it intensifies by further increasing the local resistance through loss of temper of spring contacts, formation of oxide film on contacts and wires and leakage currents through carbonisation of insulation and tracking paths. Fire can then result in the presence of combustible materials and this may release noxious fumes. Overheating may not be visually apparent. Burns may result from touching overheated components. HANDLING Care must be taken to avoid damage to any component parts of electrical connectors during installation and use. Although there are normally no sharp edges, care must be taken when handling certain components to avoid injury to fingers. Electrical connectors may be damaged in transit to the customers, and damage may result in creation of hazards. Products should therefore be examined prior to installation/use and rejected if found to be damaged. DISPOSAL Incineration of certain materials may release noxious or even toxic fumes. APPLICATION Connectors with exposed contacts should not be selected for use on the current supply side of an electrical circuit, because an electric shock could result from touching exposed contacts on an unmated connector. Voltages in excess of 30 V ac. or 42.5 V dc are potentially hazardous and care should be taken to ensure that such voltages cannot be transmitted in any way to exposed metal parts of the connector body. The connector and wiring should be checked, before making live, to have no damage to metal parts or insulators, no solder blobs, loose strands, conducting lubricants, swarf, or any other undesired conducting particles. Insulation resistance should be checked to make certain that no low resistance joints or spurious conducting paths are existing between contacts and exposed metal parts of the connector body. Further, the contact resistance of the connectors should be measured within the electrical circuit in order to identify high resistances, which result in excessive connector heating. Always use the correct application tools as specified in the Data Sheet/Catalogue. Do not permit untrained personnel to wire, assemble or tamper with connectors. For operation voltage please see appropriate national regulations. IMPORTANT GENERAL INFORMATION (i) Air and creepage paths/Operating voltage The admissible operating voltages depend on the individual applications and the valid national and other applicable safety regulations. Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c....... Seite 14 von 14 Assembly instruction CAS25022E APD 6-/7-way For this reason the air and creepage path data are only reference values. Observe reduction of air and creepage paths due to PC board and/or harnessing. (ii) Temperature All information given are temperature limits. The operation temperature depends on the individual application. (iii) Other important information ITT Industries continuously endeavours to improve their products. Therefore, ITT Industries products may deviate from the description, technical data and shape as shown in this catalog and data sheets. (iv) Harnessing and Assembly Instructions If applicable, our special harnessing and/or assembly instruction has to be adhered to. This is provided on request. ITT Industries Cannon GmbH Cannonstrasse 1 D-71384 Weinstadt Tel. +49 (0) 7151 699-0 Fax. +49 (0) 7151 699-217 info@de.itt.com www.ittcannon.com Bearbeitet: Geprüft: Norm: Änd.-Stand: Änd.-Datum: AKU / WD NK HES -4263W 11.06.2012 ITT Cannon GmbH, D-71384 Weinstadt file: t:\c...\c.......