8321SHABE22

C&K 8020 Series Snap-acting Momentary Pushbutton Switches Features/Benefits • Positive tactile feel • Multi-positions available • Wide variety of termination options • Epoxy terminal seal compatible with bottom wash cleaning Typical Applications • Instrumentation • Computer peripherals • Telecommunications equipment A Pushbutton • RoHS complient models available Models Available Specifications CONTACT RATING: B contact material (8X25 Models): 0.4 VA max. @ 20 V AC or DC maximum. G contact material (8X21, U8X1 Models): 1 AMP @ 120 V AC or 28 V DC or 0.4 VA max. @ 20 V AC or DC max. Note: Break-before-makecontacts. Multi-pole contacts do not make and break simultaneously. See page A-41 for additional ratings. ELECTRICAL LIFE: 60,000 make-and-break cycles at full load. CONTACT RESISTANCE: Below 50 mΩ typ. initial @ 2-4 V DC, 100 mA, for both silver and gold plated contacts. INSULATION RESISTANCE: 109Ω min. DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level. OPERATING TEMPERATURE: 8X2X MODELS: –30ºC to 75ºC. U8X1 MODELS: –30ºC to 65ºC. CAP INSTALLATION FORCE: 10 lbs. max. permissible. SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). NOTE: Any models supplied with B, P, R, or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. Materials CASE: Glass filled nylon 6/6 or diallyl phthalate (DAP), flame retardant (UL 94V-0). PLUNGER: Glass filled nylon or glass filled polyester (PBT) (UL 94V-0). CAP & FRAME: Nylon, black, standard. BUSHING: Brass or zinc, nickel plated. HOUSING: Stainless steel. SWITCH SUPPORT: Brass or steel, matte-tin plated. N.O. & N.C. CONTACTS: 8X21, U8X1 MODELS: G contact material: Coin silver, with gold plate over nickel plate. See page A-41 for additional contact materials. 8X25 MODELS: B contact material: Copper alloy, with gold plate over nickel plate. See page A-41 for additional contact materials. COMMON CONTACT & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. TERMINAL SEAL: Epoxy. Refer to slodering and cleaning Technical Data Chapter. HARDWARE: Nut & Locking Ring: Brass, nickel plated; Lockwasher: Steel, nickel plated. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages A-28 thru A-43. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function 8121 SPDT On-Mom. 1 Amp 8125 SPDT On-Mom. 0.4VA 8221 DPDT On-Mom. 1 Amp 8225 DPDT On-Mom. 0.4VA 8321 3PDT On-Mom. 1 Amp 8325 3PDT On-Mom. 0.4VA 8421 4PDT On-Mom. 1 Amp 8425 4PDT On-Mom. 0.4VA Note: UL/CSA models available, see page A-28 and A-29. Actuator or Plunger S Plunger NONE Snap-in J80 Snap-in J81 Snap-in w/frame J82 Snap-in w/frame for LED J83 Snap-in w/frame & flush cap J84 Snap-in w/frame for LED, flush cap J85 Snap-in w/frame & LED J95 PC w/V-bracket & LED L Plunger M Snap-fitting plunger Bushing D9 .280" high, keyway H .250" high, flat NONE No bushing choice required D .280" high, keyway D2 .288" high, flat D3 .180" high D8 .288" high, flat H9 .250" high, flat, hi torque Y .350" high, keyway Y3 6.35mm high, keyway, hi torque Y4 .378" high, flat, hi torque Y9 .350" high, keyway Terminations A Right angle, PC thru-hole AV2 Vertical right angle, PC thru-hole C PC Thru-hole Z Solder lug A2 Right angle, PC thru-hole A3 Right angle, snap-in, PC thru-hole Contact Material B Gold K Gold, tin-lead P Gold, matte-tin G Gold over silver L Gold over silver, tin-lead R Gold over silver, matte-tin Seal E Epoxy I Epoxy potted base Cap Color 2 Black NONE Models without caps 1 White 3 Red V2 V3 V4 V6 V7 V8 V9 .555" high, V-bracket .460" high, V-bracket .630" high, V-bracket .460" high, V-bracket .630" high, V-bracket .953" high, V-bracket 1.150" high, V-bracket Frame Color 2 Black NONE Models without frame 1 White 3 Red 5 Yellow 6 Green 9 Gray LED Color 3 Red NONE Models without LED 5 Yellow 6 Green 4 5 6 7 9 Orange Yellow Green Blue Gray A4 Right angle, PC thru-hole, reversed terminals A6 Right angle, PC thru-hole AV Vertical right angle, PC thru-hole AV1 Vertical right angle, PC thru-hole AV3 Vertical right angle, snap-in, PC thru-hole R Right angle with PCB R2 Right angle with PCB, reversed terminals V31 .460" high, snap-in V-bracket V61 .460" high, snap-in V-bracket W .750" long, wire wrap W1 .964" long, wire wrap W3 .425" long, wire wrap W4 1.062" long, wire wrap Z3 Quick connect Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–27 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton SWITCH FUNCTION SWITCH FUNCTION POS. 1 POS. 2 UL/CSA* MODEL NO. CONNECTED TERMINALS POS. 1 POS. 2 NO. POLES MODEL NO. C&K marking on opposite side C&K marking on opposite side SCHEMATIC 8121 SP U811 ON ON MOM. 1-3 1-2 SPDT MOM. 8125 SPDT Part number shown: 8121SHZGE Terminal Nos. For Reference Only ON ON MOM. 1-3,4-6 1-2,4-5 DPDT MOM. 8221 DP U821 8225 DPDT Part number shown: 8221SHZGE Terminal Nos. For Reference Only ON ON MOM. 1-3,4-6,7-9 1-2,4-5,7-8 3PDT MOM. 8321 3P U831 8325 3PDT Part number shown: 8321SHZGE MOM. = Momentary *U811 thru U841 model numbers with all options (except R, R2 terminations) when ordered with G ,L or R contact material. Terminal Nos. For Reference Only 8X25 models must be ordered with B, K or P contact material. 8X21 and U8X1 models must be ordered with G, L or R contact material. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–28 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches SWITCH FUNCTION SWITCH FUNCTION POS. 1 POS. 2 UL/CSA* MODEL NO. CONNECTED TERMINALS POS. 1 POS. 2 A Pushbutton NO. POLES MODEL NO. C&K marking on opposite side C&K marking on opposite side SCHEMATIC 8421 4P U841 ON ON MOM. 1-3,4-6,7-9,10-12 1-2,4-5,7-8,10-11 4PDT MOM. 8425 4PDT Part number shown: 8421SHZGE MOM. = Momentary * U811 thru U841 model numbers when ordered with G, L or R contact material. with all options (except R, R2 terminations) Terminal Nos. For Reference Only 8X25 models must be ordered with B, K or P contact material. 8X21 and U8X1 models must be ordered with G, L or K contact material. CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER FRAME COLOR J80 SNAP-IN PANEL MOUNTING OPTION CODE ** CAP AND FRAME COLOR BLACK No Frame Color (J80 option) WHITE RED ORANGE YELLOW GREEN BLUE GRAY PANEL MOUNTING NOTE: No frame color choice required. ** Increase this dim. to .620/.625 (15,75/15,88) for .091/.125 (2,31/3,18) thk. panels. 2 NONE 1 3 4 5 6 7 9 J81 SNAP-IN WITH FRAME Other colors available, consult Customer Service Center. Cap and Frame Finish: matte. NOTE: Caps and frames available separately, see pages A-42 and A-43. ** NOTE: Available with C, W-W4, Z or Z3 terminations and SPDT and DPDT models only. ** Increase this dim. to .620/.625 (15,75/15,88) for .091/.125 (2,31/3,18) thk. panels. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–29 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches CAP COLOR A Pushbutton J83 ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER FRAME COLOR SNAP-IN WITH FRAME AND FLUSH CAP PANEL MOUNTING ** J82 SNAP-IN WITH FRAME FOR LED LED not included. For LED information, see page A-43. J84 SNAP-IN WITH FRAME FOR LED, FLUSH CAP LED not included. For LED information, see page A-43. OPTION CODE CAP AND FRAME COLOR BLACK WHITE RED ORANGE YELLOW GREEN BLUE GRAY Other colors available, consult Customer Service Center. Cap and Frame Finish: matte. Available with C, W-W4, Z or Z3 terminations and SPDT and DPDT models only. NOTE: Caps and frames available separately, see pages A-42 and A-43. 2 1 3 4 5 6 7 9 Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–30 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches CAP COLOR LED COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER FRAME COLOR A Pushbutton J85 SNAP-IN WITH FRAME AND LED PANEL MOUNTING * * Increase this dim. to .620/.625 (15,75/15,88) for .091/.125 (2,31/3,18) thk. panels. 8121J85ZGE223 SPST Available with C, W-W4, Z or Z3 terminations and SPDT models only. For LED information see page A-43. NOTE: Caps & frames available separately, see pages A-42 and A-43. OPTION CODE CAP AND FRAME COLOR BLACK WHITE RED ORANGE YELLOW GREEN BLUE GRAY OPTION CODE LED COLOR RED YELLOW GREEN 2 1 3 4 5 6 7 9 3 5 6 For LED information see page A-43. CAP COLOR ACTUATOR—PC MOUNT ACTUATOR OR PLUNGER LED COLOR J95 PC WITH V-BRACKET AND LED PC MOUNTING OPTION CODE CAP AND FRAME COLOR BLACK WHITE RED ORANGE YELLOW GREEN BLUE GRAY OPTION CODE LED COLOR RED YELLOW GREEN 2 1 3 4 5 6 7 9 NOTE: Caps available separately, see page A-42. Available with V3 terminations and SPDT models only. 3 5 6 8121J95V3GE23 SPST For LED information see page A-43. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–31 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton S PLUNGER AVAILABLE BUSHINGS D, D9 H, H9 Y, Y9 Y3 DIM. ‘A’ FOR C, W-W4, Z & Z3 TERMINATIONS .244 (6,20) .218 (5,54) .203 (5,16) (5,54) .185 (4,70) N/A N/A PLUNGER ACTUATOR OR PLUNGER DIM. ‘A’ FOR A, A2, A3, A4, A6, AV-A 3, R & R2 TERMINATIONS .228 (5,79) .202 (5,13) .187 (4,75) (5,13) .169 (4,29) .232 (5,89) .162 (4,11) DIM. ‘A’ FOR V3-V61 TERMINATIONS .224 (5,69) .198 (5,03) .183 (4,65) (5,03) .165 (4,19) .228 (5,79) .158 (4,01) NONE Y4 NO PLUNGER CHOICE REQUIRED (JXX ACTUATORS) D2, D8 D3 L PLUNGER AVAILABLE BUSHINGS Y, Y9 Y4 DIM. ‘B’ FOR C, W-W4, Z & Z3 TERMINATIONS .178 (4,52) .090 (2,29) DIM. ‘B’ FOR A, A2, A3, A4, A6, AV-A 3, R & R2 TERMINATIONS .162 (4,11) .074 (1,88) DIM. ‘B’ FOR V3-V61 TERMINATIONS .158 (4,01) .070 (1,78) AVAILABLE BUSHINGS DIM. ‘C’ FOR C, W-W4, Z & Z3 TERMINATIONS .297 (7,54) .267 (6,78) .259 (6,58) (6,78) .259 (6,58) N/A N/A DIM. ‘C’ FOR A, A2, A3, A4, A6, AV-A 3, R & R2 TERMINATIONS .281 (7,14) .251 (6,38) .243 (6,17) (6,37) .243 (6,17) .273 (6,93) .361 (9,17) DIM. ‘C’ FOR V3-V61 TERMINATIONS .277 (7,04) .247 (6,27) .239 (6,07) (6,27) .239 (6,07) .269 (6,83) .357 (9,07) M SNAP-FITTING PLUNGER D, D9 H, H9 Y, Y9 Y3 Y4 D2, D8 D3 N/A = NOT AVAILABLE NOTE: When selecting plunger option, bushing selection must also be made, see next page. No plunger option is required when any JXX actuator option is selected. Additional plunger lengths are available on SPDT and DPDT models, consult Customer Service Center. Not all plunger lengths sufficient for use with caps, see page A-42. BUSHING NONE NO BUSHING CHOICE REQUIRED (JXX ACTUATORS) D .280" HIGH THREADED, KEYWAY D9 .280" HIGH UNTHREADED, KEYWAY H .250" HIGH THREADED, FLAT H9 .250" HIGH UNTHREADED, FLAT Y .350" HIGH THREADED, KEYWAY Y9 .350" HIGH UNTHREADED, KEYWAY 1/4-40 UNS-2A D9 bushing standard with A-A6, R, R2 AV-AV3 terminations. H bushing standard with C, W-W4, Z or Z3 terminations. H, H9 bushings not available on single pole models with A3-A6, R, R2 terminations. Will withstand 12 in./lbs. of torque with no distortion. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–32 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches BUSHING Y3 6.35mm THREADED, KEYWAY A D2 D8 .288" HIGH THREADED, FLAT .288" HIGH UNTHREADED, FLAT Y4 .378" HIGH THREADED, FLAT D3 .180" HIGH UNTHREADED Pushbutton 1/4-40 UNS-2A Y3 & Y4 bushings not available on single pole models with A3-A6, R, R2 terminations. Will withstand 12 in./lbs. of torque with no distortion. D2, D8 bushings not available with C, W-W4, Z, Z3 terminations. D3 bushing available with A, A2, A3, AV, AV2, AV3 and V2-V61 terminations only. NOTE: No bushing option choice required when JXX actuator option is selected. When selecting bushing option, plunger selection must also be made, see previous page. Plunger lengths vary with bushing and termination options selected. NOTE: Two mounting nuts, locking ring and lockwasher supplied standard with threaded bushings. Optional mounting nut and locking ring styles available, see section “Technical Data and Additional Hardware”. TERMINATIONS Z SOLDER LUG C PC THRU-HOLE PC MOUNTING SPDT thru 4PDT Not available with J95 actuator, K, L, P or R contact material. SPDT thru 4PDT Not available with J95 actuator option. Z3 QUICK CONNECT W W1, W3, W4 WIRE WRAP OPTION CODE DIM ‘A’ .750 (19,05) .964 (24,49) .425 (10,80) 1.062 (26,97) W DIM `A' W1 W3 W4 SPDT thru 4PDT Not available with J95 actuator, K, L, P or R contact material. Mating quick connector available,order part number 530100000, page A-42. Not available with J95 actuator option. SPDT thru 4PDT Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–33 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton A RIGHT ANGLE, PC THRU-HOLE TERMINATIONS 8121SD9AGE SPDT .138 (3,51) A3 RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING Not available with JXX actuators and I seal. Terminal bend radii and lead-in manufacturing option. A RIGHT ANGLE, PC THRU-HOLE 8221SD9AGE DPDT SECTION A-A A3 RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING Not available with JXX actuators and I seal option. Terminal bend radii and lead-in manufacturing option. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–34 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches TERMINATIONS A RIGHT ANGLE, PC THRU-HOLE A Pushbutton PC MOUNTING 8321SD9AGE 3PDT SECTION A-A Not available with JXX actuators and I seal option. Terminal bend radii and lead-in manufacturing option. A2 RIGHT ANGLE, PC THRU-HOLE PC MOUNTING 8121SD9A2GE SPDT Not available with JXX actuators, I seal option. Terminal bend radii and lead-in manufacturing option. A4 RIGHT ANGLE, PC THRU-HOLE, REVERSED TERMINALS 8121SD9A4GE SPDT Not available with JXX actuators, D3, H, H9, Y3, Y4 bushings and I seal. Terminal bend radii and lead-in manufacturing option. The A4 and R2 termination options are functionally identical and fit the same PC mounting pattern. The switches, however, are shifted relative to the mounting holes. The PC pattern must clear the switch support legs. Unlike the R2, the A4 option is available with UL/CSA. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–35 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton A6 RIGHT ANGLE, PC THRU-HOLE TERMINATIONS PC MOUNTING 8121SD9A6GE SPDT The A6 and R termination options are functionally identical and fit the same PC mounting pattern, The switches, however, are shifted relative to the mounting holes. The PC pattern must clear the switch support legs. Unlike the R, the A6 option is available with UL/CSA. Not available with JXX actuators, D3, H, H9, Y3, Y4 bushings and I seal. Terminal bend radii and lead-in manufacturing option. R RIGHT ANGLE WITH PCB PC MOUNTING 8121SD9RGE SPDT Not available with JXX actuators, D3, H, H9, Y3, Y4 bushings, I seal option. R termination not UL/CSA approved. R2 RIGHT ANGLE WITH PCB, REVERSED TERMINALS PC MOUNTING 8121SD9R2GE SPDT Not available with JXX actuators, D3, H, H9, Y3, Y4 bushings, I seal option. R2 termination not UL/CSA approved. Reversed terminals AV VERTICAL RIGHT ANGLE, PC THRU-HOLE, .100" PITCH PC MOUNTING 8121SD9AVGE SPDT Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–36 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches TERMINATIONS AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150" PITCH A Pushbutton 8121SD9AV2GE SPDT AV3 VERTICAL RIGHT ANGLE, SNAP-IN,, PC THRU-HOLE, .150" PITCH AV1 VERTICAL RIGHT ANGLE, EXTENDED, PC THRU-HOLE, .150" PITCH PC MOUNTING Not available with JXX actuators and I seal. Terminal bend radii and lead-in manufacturing option. AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150" PITCH 8221SD9AV2GE DPDT AV3 VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, .150" PITCH AV1 VERTICAL RIGHT ANGLE, EXTENDED, PC THRU-HOLE, .150" PITCH PC MOUNTING .15 (3,8) Not available with JXX actuators and I seal. Terminal bend radii and lead-in manufacturing option. .33 TYP. (8,4) Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–37 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton AV2 TERMINATIONS VERTICAL RIGHT ANGLE, PC THRU-HOLE, 150" PITCH 8321SD9AV2GE 3PDT AV1 VERTICAL RIGHT ANGLE, EXTENDED, PC THRU-HOLE, .150" PITCH PC MOUNTING AV3 VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, .150" PITCH .15 (3,8) Not available with JXX actuators and I seal. Terminal bend radii and lead-in manufacturing option. .33 TYP. (8,4) AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE, 150" PITCH 8421SD9AV2GE 4PDT AV1 VERTICAL RIGHT ANGLE, EXTENDED, PC THRU-HOLE, .150" PITCH PC MOUNTING AV3 VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, .150" PITCH Not available with JXX actuators and I seal. Terminal bend radii and lead-in manufacturing option. V2, V6, V7, V8 VERTICAL MOUNT, V-BRACKET V61 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING OPTION CODE DIM ‘A’ .555 (14,10) .460 (11,68) .630 (16,00) .953 (24,21) Third Angle Projection V2 V6, V61 V7 8121SD3__GE SPDT Not available with JXX actuators and I seal. V8 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–38 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches TERMINATIONS V2, V6, V7, V8 VERTICAL MOUNT, V-BRACKET V61 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING A Pushbutton 8221SD3__GE DPDT OPTION CODE DIM ‘A’ .555 (14,10) .460 (11,68) .630 (16,00) .953 (24,21) V2 V6, V61 V7 Not available with JXX actuators and I seal. V8 V2, V7, V8 VERTICAL MOUNT, V-BRACKET PC MOUNTING 8321SD3__GE 3PDT OPTION CODE DIM ‘A’ .555 (14,10) .630 (16,00) .953 (24,21) V2 V7 Not available with JXX actuators and I seal. V8 V2, V7, V8 VERTICAL MOUNT, V-BRACKET PC MOUNTING 8421SD3__GE 4PDT OPTION CODE Not available with JXX actuators and I seal. DIM ‘A’ .555 (14,10) .630 (16,00) .953 (24,21) Third Angle Projection V2 V7 V8 Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–39 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton TERMINATIONS V3, V4, V9 VERTICAL MOUNT, V-BRACKET V31 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8121SD3__GE SPDT OPTION CODE DIM ‘A’ .460 (11,68) .630 (16,00) 1.150 (29,21) V3, V31 V4 Not available with J8X actuators and I seal. V9 V3, V4, V9 VERTICAL MOUNT, V-BRACKET V31 VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8221SD3__GE DPDT OPTION CODE DIM ‘A’ .460 (11,68) .630 (16,00) 1.150 (29,21) V3, V31 V4 V9 Not available with J8X actuators and I seal. V4, V9 VERTICAL MOUNT, V-BRACKET PC MOUNTING .630 (16,00) 8321SD3V4GE 3PDT Not available with JXX actuators and I seal. OPTION CODE DIM ‘A’ .630 (16,00) 1.150 (29,21) V4 V9 Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–40 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches TERMINATIONS V4, V9 VERTICAL MOUNT, V-BRACKET A Pushbutton PC MOUNTING .630 (16,00) 8421SD3V4GE 4PDT OPTION CODE DIM ‘A’ .630 (16,00) 1.150 (29,21) V4 V9 Not available with JXX actuators and I seal. CONTACT MATERIAL OPTION CODE RoHS COMPLIANT * YES NO YES YES NO YES RoHS COMPATIBLE * YES YES YES YES YES YES GOLD OVER SILVER 2,3 GOLD 1 CONTACT MATERIAL TERMINAL PLATING GOLD 1 TIN-LEAD 4 MATTE-TIN GOLD 3 5 RATINGS B K P G L R LOW LEVEL/DRY CIRCUIT 8x25 MODELS ONLY: 0.4 MAX. @ 20 V AC OR DC MAX. 8X21, U8X1 MODELS ONLY: 0.4 VA MAX @ 20 V AC OR DC MAX. OR 1 AMP @ 120 V AC OR 28 V DC. TIN-LEAD 4 MATTE-TIN 5 LOW LEVEL/DRY CIRCUIT OR POWER * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 2 3 4 5 ALL CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. N.O. AND N.C. CONTACTS: Coin silver, with gold plate over nickel plate. COMMON CONTACTS & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. TERMINALS: Copper alloy, with tin-lead alloy over nickel plate. TERMINALS: Copper alloy, with matte-tin over nickel plate. NOTE: Any models supplied with B, P, R or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. U811-U841 models with all options (except R, R2 terminations) when ordered with mandatory G, R or L contact material. B, P or K contact material must be ordered with 8X25 models. G, R or L contact material must be ordered with 8X21, U8X1 models. P, R, K or L contact material not available with Z, Z3 terminations. SEAL E EPOXY SEAL I EPOXY POTTED BASE NO. POLES SP DP 3P 4P DIM ‘A’ .410 (10,41) .440 (11,18) .505 (12,83) .505 (12,83) NOTE: Available with C, W-W4, Z, Z3 terminations only. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–41 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches A Pushbutton Cap AVAILABLE HARDWARE Cap Cap PART NO. PART NO. WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY PART NO. WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY 708901000 708902000 708903000 708904000 708905000 708906000 708907000 708909000 Material: Nylon Finish: Gloss 752701000 752702000 752703000 752704000 752705000 752706000 752707000 752709000 Material: Nylon Finish: Gloss 801801000 801802000 801803000 801804000 801805000 801806000 801807000 801809000 Material: Nylon Finish: Gloss WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY Cap, Snap-fitting plunger Cap, Snap-fitting plunger Cap, J80, J81, J82, J83 & J84 options only PART NO. PART NO. WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY PART NO. WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY PART NO. WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY 894001000 894002000 894003000 894004000 894005000 894006000 894007000 894009000 Material: Nylon Finish: Gloss Frame 894101000 894102000 894103000 894104000 894105000 894106000 894107000 894109000 Material: Nylon Finish: Gloss Frame 484601000 484602000 484603000 484604000 484605000 484606000 484607000 484609000 Material: Nylon Finish: Gloss 798201000 798202263 798203000 798204000 798205000 798206000 798207000 798209000 Material: Nylon Finish: Matte WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY Cap, J85 & J95 options only PART NO. PART NO. PART NO. WHITE BLACK RED YELLOW GREEN GRAY PART NO. 615601000 615602263 615603000 615605000 615606000 615609000 Material: Nylon Finish: Matte 613301000 613302263 613303000 613305000 613306000 613309000 Material: Nylon Finish: Matte WHITE BLACK RED YELLOW GREEN GRAY 459701000 459702000 459703000 459704000 459705000 459706000 459707000 459709000 Material: Nylon Finish: Gloss 459701000 459702000 459703000 459704000 459705000 459706000 459707000 459709000 Material: Nylon Finish: Matte WHITE BLACK RED ORANGE YELLOW GREEN BLUE GRAY Fits Z3 Termination female connector NOTE: Additional nuts, locking rings and lockwashers available separately, see section “Technical Data and Additional Hardware”. Other cap & frame colors available, consult Customer Service Center. PART NO. 530100000 Available in loose pieces. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–42 www.ittcannon.com C&K 8020 Series Snap-acting Momentary Pushbutton Switches AVAILABLE HARDWARE Frames snap into panel opening and are independent from switch mounting. Accurate positioning of the PC mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. Available in two basic styles and four panel thicknesses .047-.125 in. Material: Nylon. Finish: Matte. TYPICAL APPLICATION A Pushbutton .047" (1,19) PANEL THK. PART NO. .062" (1,57) PANEL THK. PART NO. .090" (2,29) PANEL THK. PART NO. .125" (3,18) PANEL THK. PART NO. 432501000 432502263 432503000 432505000 432506000 432509000 432601000 432602263 432603000 432605000 432606000 432609000 432701000 432702263 432703000 432705000 432706000 432709000 432801000 432802263 432803000 432805000 432806000 432809000 WHITE BLACK RED YELLOW GREEN GRAY Panel Inserts Above frames (part nos. 432XXXXXX) are also available with insert which accepts LED for indicator light assembly. Order insert separately from frame. Blank insert panel (without hole for LED) also available. LED not included. PANEL INSERT WITH HOLE FOR LED PART NO. BLANK PANEL INSERT WITHOUT HOLE FOR LED PART NO. 894901000 894902000 894903000 894905000 894906000 894909000 476601000 476602000 476603000 476605000 476606000 476609000 WHITE BLACK RED YELLOW GREEN GRAY Special colors, custom markings available, consult Customer Service Center. LED INFORMATION SWITCHES WITH LED SUPPLIED: J85, J95 OPTIONS: Rectangular LEDs are supplied on 8020 Series pushbutton switches with J85 and J95 options. These LEDs are factory installed and are not replaceable. The following specifications apply: TYP. FORWARD VOLTAGE TYP. FORWARD CURRENT 20 mA 2.1 V 10 mA 20 mA 2.5 V MAX RATINGS AT 25ºC AMBIENT TEMPERATURE FORWARD VOLTAGE CONTINUOUS FORWARD CURRENT 50 mA 30 mA 50 mA POWER DISSIPATION 125 mW 75 mW 125 mW .230 DIA. (5,84˘) .030 (0,76) .340 (8,64) Suggested LED for J82 & J84 options. Dimensions for reference only. .750 (19,05) Flat denotes cathode. .200 DIA. (5,08˘) .025 SQ. TYP. (0,63) OPTION CODE 6 3 5 COLOR Green Red* Yellow TYP. INTENSITY 1.0 mcd 0.5 mcd 4.0 mcd Process Information: Soldering to LED leads must be completed within 5 seconds at 500ºF (260ºC) maximum. Caution: Circuit elements must limit forward current of LED to 50mA max. continuous. * Extra-bright red LED available (typ. intensity 4.5 mcd), consult Customer Service Center. LEDs are not supplied with J82, J84 options. LED snaps into switch frame surrounding actuator and is wired externally. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–43 www.ittcannon.com